Variquest Perfecta 2400STP User manual

Assembly Instructions
Perfecta® 2400STP
Poster Design System
Assembly Instructions
Perfecta® 2400STP
Poster Design System

Page 2Perfecta® 2400STP Assembly Instructions
Package Contents
The following items are included in the shipping container:
Notes:
•A4/Letter sheet paper (not included) is needed for printhead
alignment during set-up.
•LAN not included (needed if LAN connection required).
Installation Notes
• To unpack the printer, you need at least 6.5 feet at the side. The
crate size is:
- Length: 52 inches
- Width: 22.4 inches
- Height: 25 inches
• Tools required: Screwdriver (included)
• Two people are required to perform some tasks.
• Time required to assemble the printer is approximately 100
minutes.
Unpack Printer Stand
1. Cut the straps and open the box.
Important
To avoid scratches, install a blanket on the floor.
2. Remove the documentation and carton tray on top of the printer.
3. Remove the stand accessories from the tray:
4. Locate and remove the packaged multi-sheet tray inside one of the
legs.
5. Remove the foam piece (keep it for use in the following steps) and
unpack the multi-sheet tray.
1 - Printer 8- Stand Pieces:
2 - Multi-sheet Tray - Metal Stoppers
3 - Documentation: - Right Leg
- Assy Instructions - Right Foot
- Quick Start Guide - Basket Frame
- Crossbrace
- Left Foot
4 - Screwdriver
5 - Black Knobs
6 - Power Cords - Left Leg
7 - Cartridges 9 - Re-feed Preventers
- Metal stoppers [1]
- Right Leg [2]
- Right Foot [3]
- Basket Frame [4]
- Screwdriver [5]
- Crossbrace [6]
- Left Foot [7]
- Left Leg [8]
1
2
3
12
6
4
5
7
8

Perfecta® 2400STP Assembly Instructions Page 3
Assemble Printer Stand
1. Fix one foot to a leg with 4 screws.
2. Repeat the process for the other foot and leg.
3. Place the foam removed previously on the floor and place cross
brace on top, making sure the yellow plastic parts are facedown.
4. Place leg into slot on cross brace with long side of foot as shown.
5. Attach leg to cross brace with 3 screws at the inside of leg.
Important
Do not fully tighten the screws.
6. Slide foam to the opposite side and place the other leg into the slot
on the cross brace.
Important
Make sure the 2 basket supports are on the same side.
7. Attach the leg to the cross brace with 3 screws on the inside of the
leg.
Important
Do not fully tighten the screws.
8. Turn the stand upright.

Page 4Perfecta® 2400STP Assembly Instructions
9. Attach the outside of leg to the cross-brace with 2 screws. Repeat
with the other leg.
Important
Do not omit this step or the printer will not be stabilized correctly.
10. Fully tighten all of the screws on the stand.
11. Lock the 4 wheels to finish the stand assembly.
12. Locate the 2 metal stoppers and install on both ends of the cross
brace with screws provided.
Note: There is only one position possible for each stopper.
13. Locate and unpack the basket frame.
14. Remove tape and unfold the fabric.
15. Insert basket frame into the fabric. See image for correct
installation.
16. Clip basket frame to the feet.

Perfecta® 2400STP Assembly Instructions Page 5
Remove Printer Packaging
1. Open the printer box.
2. Remove tape from film, then remove tray and box.
3. Remove tape from the endcaps and remove the packing pieces.
4. Remove any tape from the endcaps.
5. Tear plastic bag away from top and sides of printer. Leave printer
sitting on packaging box.
Attach Printer to Stand
1. Make sure the stand and printer are in the correct position for
assembly.
2. Look for the marks on the printer for correct installation.
3. Locate the yellow locator parts on the stand for installing the
printer.
Note: Review steps 4, 5, and 6 before connecting the printer
onto the stand.

Page 6Perfecta® 2400STP Assembly Instructions
4. Check metal stoppers on back of the stand to ensure printer is in
the correct position.
5. Check alignment of lateral marks on printer for correct positioning.
6. Install printer onto the yellow locator parts.
7. Locate the 4 screw-in black knobs.
8. Attach the printer to the stand from underneath with the 4 screw-in
black knobs.
9. The assembled printer should appear as shown.

Perfecta® 2400STP Assembly Instructions Page 7
Install the Re-feed Preventer
1. Slide re-feed preventer into the bracket slot of the scanner input
platen. Repeat the process on the other side of the input platen.
Note: Use the mark on the scanner input platen for use as a
reference position.
1.Remove the orange tapes from the top and rear of the printer.
Remove all the protective film from the front panel and surface of
the printer.
2.Remove all transparent tape from the printer.
3.Remove the desiccant bag.
4.Open the roll cover.
5.Remove the 2 spindle tapes and retainers.
Remove Shipping Tape & Prepare Machine

Page 8Perfecta® 2400STP Assembly Instructions
6. Open printhead cover and remove protective foam.
Important
Do not touch the printhead or blue latch. No printhead installation
is required.
7. Close printhead door.
8.Install the multi-sheet tray that was previously unpacked.
9. Open the front window.
10. Rotate and remove the 2 pins.

Perfecta® 2400STP Assembly Instructions Page 9
11. If all protective foams are removed, close all open covers and
windows.
12.Connect power cable to the printer and an outlet.
13.If connecting by LAN, connect Ethernet cable to printer. If not, you
can connect via WiFi using the front panel instructions.
14.After all cables are connected, power on the printer.
15.Select and confirm your Language and Country/Region.

Page 10 Perfecta® 2400STP Assembly Instructions
16. At the prompt to add ink cartridges, open the ink cartridge cover
and insert the 4 ink cartridges, clicking them into place. When
done, close the cover.
17.Follow the instructions to load paper when prompted to align the
printhead.
18.Extend the input and output trays.
19.When prompted, load an A4/Letter sheet into the multi-sheet tray
(1) and adjust tray (2).
20.Press OK. Printhead alignment will be initialized.
21.If the printer is connected via LAN; connection will be automatic. If
you prefer to connect via WiFi, follow the instructions on the front
panel to connect to a network.

Perfecta® 2400STP Assembly Instructions Page 11
Load Paper Roll
1. Load the paper roll onto the spindle. Be sure paper winds over (in
front of) the roll.
2. Load spindle with paper roll into the printer.
3. Insert edge of paper into printer until printer detects it.
Technical Support
For technical assistance, please contact your authorized VariQuest
dealer or the VariQuest Technical Support team:
•Email: [e-mail]
•Phone: [phone]
Y2900702 Rev A 01/18
©2018 Varitronics, LLC. All rights reserved.

Y2900702 Rev A 01/18
©2018 Varitronics, LLC. All rights reserved.
Y2900702 Rev A 01/18
©2018 Varitronics, LLC. All rights reserved.