VAT 292 Series Assembly instructions

Installation, Operating &
Maintenance Instructions
603585EA
Edition
2015
-
05
-
18
Angle valve with soft-pump function
with single acting pneumatic actuator and closing spring (NC)
Series 292
DN 100 – 160 mm (I. D. 4” – 6”)
This manual is valid for the following product ordering numbers:
292 .. - …. - ….
Sample picture

Series 29
2
2
/
31
Edition
2015
-
05
-
18
603585EA
Imprint
Manufacturer
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Website:
Phone:
Fax:
Email:
www.vatvalve.com
[phone]
[phone]
[email protected]
Publisher VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Editor VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Print VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Copyright © VAT Vakuumventile AG 2015
No part of these instructions may be reproduced in any way (photo-
copies, microfilms or any other reproduction processes) nor may it be
manipulated with electronic systems, duplicated or distributed without
written permission from VAT. Offenders are liable to pay damages.
The original VAT firmware and updated state of the art versions of the
VAT firmware are intended for use with VAT products. The VAT firmware
contains a limited, time unlimited user license. The VAT firmware may not
be used for purposes other than those intended nor is it permitted to
make copies of the VAT firmware. In particular, it is strictly forbidden to
give copies of the VAT firmware to other people.
The use of trade names, brand names, trademarks, etc. in these
Instructions does not entitle third parties to consider these names to be
unprotected and to use them freely. This is in accordance with the
meaning of the laws and acts covering brand names and trademarks.

Series 292
603585EA
Edition
2015
-
05
-
18
3
/
31
Contents
1 Description of product........................................................................5
1.1 Identification of product.......................................................................................5
1.2 Use of product.....................................................................................................5
1.3 Related documents.............................................................................................5
1.4 Important information..........................................................................................5
1.5 Technical data.....................................................................................................5
2 Safety ...................................................................................................6
2.1 Compulsory reading material..............................................................................6
2.2 Danger levels......................................................................................................6
2.3 Personnel qualifications......................................................................................7
2.4 Safety labels........................................................................................................7
3 Design and Function...........................................................................8
3.1 Design.................................................................................................................8
3.2 Function ..............................................................................................................8
4 Installation...........................................................................................9
4.1 Unpacking ...........................................................................................................9
4.2 Installation into the system................................................................................10
4.2.1 Admissible forces and bending moments.............................................11
4.3 Compressed air connection ..............................................................................12
4.4 Electrical connection.........................................................................................12
5 Operation...........................................................................................13
5.1 Normal operation...............................................................................................13
5.2 Operation under increased temperature...........................................................13
5.3 Behavior in case of compressed air pressure drop ..........................................13
5.4 Behavior in case of power failure......................................................................13
5.5 Trouble shooting ...............................................................................................14
6 Maintenance ......................................................................................15
6.1 Maintenance intervals.......................................................................................16
6.2 Required tools...................................................................................................16
6.3 Replacement of vacuum seals..........................................................................17
6.3.1 Preparatory steps..................................................................................18
6.3.2 Replacement of vacuum seals – soft-pump valve The item numbers in
brackets refer to the drawing on page ..............................................................18
6.3.3 Dismount actuator / plate assembly – main valve ................................20
6.3.4 Mount actuator / plate assembly...........................................................23
7 Repairs...............................................................................................25
8 Dismounting and Storage.................................................................26
8.1 Dismounting ......................................................................................................27
8.2 Storage..............................................................................................................27
9 Packaging and Transport.................................................................28
9.1 Packaging .........................................................................................................29
9.2 Transport...........................................................................................................29

Series 29
2
4
/
31
Edition
2015
-
05
-
18
603585EA
10 Disposal............................................................................................. 30
11 Spare parts........................................................................................ 31

Series 292 DESCRIPTION OF PRODUCT
603585EA
Edition
2015
-
05
-
18
5
/
31
1 Description of product
1.1 Identification of product
The fabrication number and order number are fixed on the product directly or by means of
an identification plate.
made in Switzerland
Fabrication No.:
292 . .- . . . .- . . . ./ . . . .
A - . . . . . .


Fabrication number
Order number
1.2 Use of product
Use product for clean and dry vacuum applications only. Other applications are only allowed
with the written permission of VAT.
1.3 Related documents
•Product data sheet
•Dimensional drawing
1.4 Important information
This symbol points to a very important statement that requires particular
attention.
Example
:
VAT disclaims any liability for damages resulting from inappropriate packaging.
1.5 Technical data
See product data sheet and dimensional drawing.

SAFETY Series 29
2
6
/
31
Edition
2015
-
05
-
18
603585EA
2 Safety
2.1 Compulsory reading material
Read this chapter prior to performing any work with or on the product. It contains important
information that is significant for your own personal safety. This chapter must have been
read and understood by all persons who perform any kind of work with or on the product
during any stage of its serviceable life.
NOTICE
Lack of knowledge
Failing to read this manual may result in property damage.
Firstly, read manual.
These Installation, Operating & Maintenance Instructions are an integral part
of a comprehensive documentation belonging to a complete technical
system. They must be stored together with the other documentation and
accessible for anybody who is authorized to work with the system at any
time.
2.2 Danger levels
DANGER
High risk
Indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
Medium risk
Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION
Low risk
Indicates a hazardous situation which, if not avoided, may result in minor or
moderate injury.
NOTICE
Command
Indicates a hazardous situation which, if not avoided, may result in property
damage.

Series 292 SAFETY
603585EA
Edition
2015
-
05
-
18
7
/
31
2.3 Personnel qualifications
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
2.4 Safety labels
Label Part No. Location on valve
DN 100: T-9001-155
DN 160: T-9001-156 On protective foil covering
the valve opening
253198 On valve body or actuators
Table 2-1

DESIGN AND FUNCTION Series 29
2
8
/
31
Edition
2015
-
05
-
18
603585EA
3 Design and Function
3.1 Design
1 Plate seal
(soft-pump valve)
2 Plate seal
(main valve)
3 Bellows
4 Closing spring
5 Bonnet seal
(soft-pump valve)
6 Bonnet seal
(main valve)
7 Setting of the
orifice opening
8 Shaft feedthrough
Valve seat side
Figure 3-1
3.2 Function
Main and bypass valve are closing by a spring (NC) and opening pneumatically.

Series 292 INSTALLATION
603585EA
Edition
2015
-
05
-
18
9
/
31
4 Installation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
4.1 Unpacking
•Make sure that the supplied products are in accordance with your order.
•Inspect the quality of the supplied products visually. If it does not meet
your requirements, please contact VAT immediately.
•Store the original packaging material. It may be useful if products must be
returned to VAT.
The protective covers may only be removed immediately before the valve is
mounted into the system. Unprotected sealing surfaces must be treated with
care and keep clean.

INSTALLATION Series 29
2
10
/
31
Edition
2015
-
05
-
18
603585EA
4.2 Installation into the system
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Do not connect or supply electrical power and compressed air before the
product is completely mounted in the system.
CAUTION
Hot surfaces
Risk of burning when touching hot surfaces.
Take safety measures in order that the valve cannot be touched during
operation. Ensure air circulation of coil.
NOTICE
Contamination
Product may get contaminated.
Always wear cleanroom gloves when handling the product.
NOTICE
Inappropriate tools
Sealing surfaces may get damaged.
Do not use sharp-edged tools.
1. Check and carefully clean sealing surfaces of valve flanges and counter flanges.
2. Install valve with connection components appropriate for ISO-K flanges according the
specification of «Table 4-1» on page 11 into account.

Series 292 INSTALLATION
603585EA
Edition
2015
-
05
-
18
11
/
31
4.2.1 Admissible forces and bending moments
DN (nom. I. D.) Axial tensile or
compressive force «F
A
» Bending moment «M»
mm inch N lbf Nm lbf · ft
100 4 250 56 27 20
160 6 300 68 42 31
A combination of both forces «F
A
» and «M» is not allowed. Please contact VAT.
Angle valve
Table 4-1

INSTALLATION Series 29
2
12
/
31
Edition
2015
-
05
-
18
603585EA
4.3 Compressed air connection
WARNING
Valve in open position
Risk of injury when compressed air is connected to the valve.
Connect compressed air only when:
– valve is installed in the vacuum system
– moving parts cannot be touched
Use clean, dry or slightly oiled air only.
Admissible air pressure range, see product data sheet.
1. Connect compressed air according to the product data sheet and dimensional drawing.
4.4 Electrical connection
DANGER
Electric shock
Parts being under voltage will result in serious injury or death.
Do not touch parts being under voltage.
NOTICE
Wrong voltage
Electrical components may get damaged.
Supply electrical components with the correct voltage.
1. Connect solenoid valve according to the product data sheet and dimensional drawing.
2. Connect position indicator according to the product data sheet and dimensional
drawing.
3. Connect heater (option) according to the wiring diagram in the product data sheet and
dimensional drawing.

Series 292 OPERATION
603585EA
Edition
2015
-
05
-
18
13
/
31
5 Operation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Do not operate before product is installed completely into the vacuum system.
CAUTION
Hot surfaces
Risk of burning at valve with heater.
Do not touch hot surfaces.
5.1 Normal operation
Main and bypass valve are closing by a spring (NC) and opening pneumatically.
5.2 Operation under increased temperature
Maximum allowed temperature, see product data sheet.
5.3 Behavior in case of compressed air pressure drop
See product data sheet.
5.4 Behavior in case of power failure
See product data sheet.

OPERATION Series 29
2
14
/
31
Edition
2015
-
05
-
18
603585EA
5.5 Trouble shooting
Failure Check Action See
Valve does not
close / open Compressed air connected correctly? Check air pressure Product data sheet
Solenoid valve
connected correctly?
Check electrical
power supply and
wiring Product data sheet
No or wrong
position indicator
signal
Position indicator
connected correctly?
Check electrical
power supply and
wiring Product data sheet
Leak at plate or
body Contamination? Clean or replace seals
Chapter «6.3
Replacement of
vacuum seals»
Table 5-1
If you need any further information, please contact one of our service centers. You will find
the addresses on our website www.vatvalve.com.

Series 292 MAINTENANCE
603585EA
Edition
2015
-
05
-
18
15
/
31
6 Maintenance
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
WARNING
Hazardous components
Human body parts may get jammed and severely injured.
Before starting maintenance:
– disconnect compressed air supply
– disconnect electrical power supply
CAUTION
Hot surfaces
Risk of burning at valve with heater.
Touch hot surfaces only if the valve has cooled down.
NOTICE
Contamination
Product may get contaminated.
Always wear cleanroom gloves when handling the product.
NOTICE
Inappropriate tools
Sealing surfaces and valve plate may get damaged.
Do not use sharp-edged tools.

MAINTENANCE Series 29
2
16
/
31
Edition
2015
-
05
-
18
603585EA
6.1 Maintenance intervals
Under clean operating conditions the valve does not require any maintenance during the
specified cycles.
For more information or a general overhaul please contact one of our service centers. You
will find the addresses on our website www.vatvalve.com.
Contamination resulting from the process may impair the function of the
valve and require more frequent maintenance.
6.2 Required tools
•Allen wrench depending on valve size
•Torque wrench 1 Nm / 20 Nm / 35 Nm
•Cross screwdriver
•Slotted screwdriver
•Open-end wrench 19 / 22
•Cleanroom wiper soaked with alcohol (2% methyl ethyl ketone)
•O-Ring removal tool; see «Table 11-1» on page 31
Figure 6-1

Series 292 MAINTENANCE
603585EA
Edition
2015
-
05
-
18
17
/
31
6.3 Replacement of vacuum seals
Figure 6-2

MAINTENANCE Series 29
2
18
/
31
Edition
2015
-
05
-
18
603585EA
6.3.1 Preparatory steps
1. Detach the soft-pump valve from the main valve by removing the 2 screws (6).
2. Remove O-rings (7) and (9) and discard them. The item number in brackets refers to
«Figure 6-3».
Figure 6-3
6.3.2 Replacement of vacuum seals – soft-pump valve
The following item numbers in brackets refer to «Figure 6-2» on page 17.
1. Remove 4 screws (59) uniformly and crosswise.
Attention: Loaded spring!
2. Withdraw "actuator/plate assembly" carefully from valve body.
3. Remove bonnet seal (O-ring, 64) from groove and discard it.
4. Pull plate seal (O-ring, 63) out of groove by picking it with a needle and discard it.
Do not damage the sealing surface!
5. Remove setscrew (4) and clean it with alcohol.
6. Remove circlip (5) and take out the setting piece (3) by pushing it from the vacuum side.
7. Remove O-rings (8, 10) and discard them.
8. Make sure that all sealing surfaces are undamaged and clean them with alcohol.

Series 292 MAINTENANCE
603585EA
Edition
2015
-
05
-
18
19
/
31
9. Lubricate new O-rings (8, 10) slightly with VAT high vacuum grease.
10. Mount lubricated O-rings (8, 10) to the setting piece (3).
11. Insert setting piece (3) and circlip (5).
Do not damage O-rings while inserting setting piece (3).
12. Mount setscrew (4) by using Loctite 222.
The dimension of 2.40 ±0.2 must be met!
13. Put new plate seal (O-ring, 63) on groove and press it crosswise into groove at 4 points.
14. Press entire plate seal (O-ring, 63) uniformly into groove.
15. Mount new bonnet seal (O-ring, 64) into groove.
16. Insert "actuator/plate" assembly carefully into the valve body.
Do not cant!
17. Mount 4 screws (59) uniformly and crosswise in 2 to 3 steps. Torque screws with
2.3Nm.
18. Mount new O-Rings (7) and (9)
19. Attach the soft-pump valve to the main valve by mounting the 2 screws (6) and torque
the screws with 2.3 Nm

MAINTENANCE Series 29
2
20
/
31
Edition
2015
-
05
-
18
603585EA
6.3.3 Dismount actuator / plate assembly – main valve
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Keep human body parts away from movable parts.
The follow item numbers in brackets refer to «Figure 6-2» on page 17.
Open the valve by means of
compressed air and hold the position
with a nonreturn valve.
If a solenoid valves is assembled to the
actuator you may use the emergency
operation knob on the solenoid valve to
remain the valve opened
Loosen and remove screws (60)
uniformly and in crosswise order
Withdraw actuator / plate assembly
carefully from body and vent the
compressed air
Remove bonnet seal (62) from groove
by using an O-ring removal tool
Remove the plate seal (61) from groove
by using O-ring removal tool
Loosen screws (42) and remove
position indicator
Loosen and remove switching cam
(41)
Turn coil spring (40) with a screwdriver
approx. 20° counter-clockwise and pull
it out of the groove
Remove solenoid valve (in case it’s
available)