Vaxcel T0389 Instruction manual

Green Grounding
Screw (C)
Headless
screw (H)
Mounting Screw (B) Wire Connector (E)
Lock Nut (D)
Mounting Plate (A) Ball Nut (F)
Back Plate
Ball Nut (F)
Rubber Pad (G)
Rubber Pad (G)
Hardware Package (included):
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0389
180404
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Warning: LED electronics can be damaged by electro static discharge (ESD)shock. Before
installation, discharge yourself by touching a grounded bare metal surface to remove this
hazard. To avoid damage, do not touch the LED module.
Green Grounding Screw (C)
Outlet Box
Wire Connector (E)
Headless Screw (H)
Mounting Plate (A)
Lock Nut
(D)
House Grounding Wire
Fixture Grounding Wire
Fixture Wire
Glass
Glass Holder
Headless screw
Ball Nut
Mounting Screw (B)
1. Thread two headless screws (H) through the mounting plate (A),
then secure them with four lock nuts (D) ( two on each side
of the mounting plate (A) ). Adjust the length of the headless screws (H) if necessary ).
Note: Make sure that the headless screws (H) are lined up horizontally, to ensure that
the fixture will be level.
2. Attach the mounting plate (A) to the outlet box by using two mounting screws (B).
Turn off the power at fuse or circuit box
Installation Steps

180404
Turn on the power at fuse or circuit box.
4. Pull out the outlet wires and house grounding wire from the outlet box. Make wire connections (E) using the
wire connectors (E):
---Connect the black wire from the fixture to the black wire from the power source.
---Connect the white wire from the fixture to the white wire from the power source.
---Attach the fixture grounding wire to the cross bar with the green grounding screw (C). Then connect it to the
house grounding wire with a wire connector (E).
Carefully put the wires back into the outlet box.
5. Attach the fixture to the cross bar (A) by inserting the headless screw (H), then secure it with two rubber pads (G)
and two ball nuts (F).
6. Attach the glass holder to back plate, use ball nut secure glass holder to fix glass.
Function and Operation
MODES OF OPERATION
Choose a mode by sliding the switch on the back of the sensor. when power is first applied, the light
will turn on immediately. Wait for 100 seconds to allow the sensor to warm up.
1. TEST MODE (daytime and nighttime operation)
● The light will turn to low-level brightness (0%~50% brightness). The light will turn to high-level brightness (100%
brightness) when motion is detected, and stay on as long as the motion is continuing. The light will revert to
low-level brightness about 5 seconds after motion is no longer detected.
2. 3H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 3 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set.
● Light will turn off automatically at dawn, and return to 3 H mode at dusk.
3. 6H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 6 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set
● Light will turn off automatically at dawn, and return to 6 H mode at dusk.
4. 0 MODE (nighttime operation only)
● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness
(100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no
longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to
low level brightness you set.
● Light will turn off automatically at dawn, and return to 0 H mode at dusk.
5.Manual Override MODE (nighttime operation only; on at dusk,off at dawn)
● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again,
the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous
settings, turn off the wall switch in 3 seconds and then turn it on again. (See Fig.1)
● The lights will turn off automatically at dawn.
FIG.2
On the back of the sensor
Time Low Level Sens
Test 3H 6H 0
AUTO Mode Manual
Override
Mode
Manual Override Operation Diagram
Turn wall switch OFF-ON
in 3 Seconds
Turn wall switch OFF-ON
in 3 Seconds again
FIG.1

180404
CUSTOMIZATION OPTIONS:
Shut-off Delay
The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to
be detected.This Shut-off delay can be set when operation is in 3, 6 or 0 Mode by using the “TIME” knob
located on the left side of the panel at the back of the sensor lens (See Fig.2) . To increase the shut-off delay,
turn the knob clockwise. To decrease shut off delay, turn the knob counterclockwise. The delay may be
adjusted from a minimum of 5 seconds to a maximum of 3 minutes. The light will stay on as long as motion is
detected continuously and will automatically turn to low-level brightness when no more motion is detected
after the delay time has passed.
Sensitivity of Motion Sensor
The sensitivity of the motion sensor can be adjusted by using the “Sens” knob located on the right side of the panel at
the back of sensor lens (See Fig.2). To increase sensitivity, turn the knob clockwise. To decrease sensitivity, turn the
knob counterclockwise. The sensitivity may be adjusted from a minimum of 5 feet to a maximum of 40 feet.
Troubleshooting
---The light does not come on at all:
1. Make sure the wall switch and circuit breaker are on.
2. Make sure the wiring is correct.
3. Cover the sensor with your palm to verify that the ambient light level is not too high.
----In Test Mode, the light stays on full brightness
1. If during daytime, make sure the slide switch is at the TEST position.
2. Whether the motion is detected at all time.
NOTE:
1. The sensitivity of the motion sensor will increase as the
environmental temperature gets cooler. For best performance,
gently clean the lens with a soft cloth every 1 or 2 months to
assure maximum sensitivity.
2. For best performance, install fixture at least 6 feet above
the ground. At such a height, the fixture will provide a
detection distance of up to 40 feet at 77 degrees
Fahrenheit. (See Fig.3)
3.The sensor detects across a detection range of 180 degrees.
(See Fig.4)
4. The sensor will be more sensitive to motion across its
detection path than motion directly towards it. (See Fig.5)
5. To reduce possible nuisances, do not mount the fixture
near a heat source like an air conditioner, vent or furnace
exhaust, or in a direction facing any reflecting object or
other light source.
5`
6`
10`
40`
Where you install your lantern is important:
Be sure the light is mounted straight on the wall;
otherwise, the detection distance may be limited.
Fig. 3 Fig. 4
180˚
Motion
Least sensitive
Motion
Most sensitive
Sensor
Fig. 5
---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours
after dusk, respectively:
1. Make sure no motion could be picked up by the sensor.
2. Make sure that mode entry is not in manual override.
---After performing 3H or 6H Mode, the light stays onfull brightness after 3 minutes:
1. Make sure there is no movement that could be picked up by the sensor.
2. Adjust the time knob counterclockwise to reduce the delay shut-off time.

180404
A
B
C
A: 18-1/4
"
B: 6-1/2 "
C: 6 "
Spare Parts List:
Mounting Hardware
5828MM(1 SET)
Glass 9953CS
The following parts are available for re-order if damaged or missing.
Green Grounding
Screw (C)
Headless Screw (H)
Mounting Screw (B)
Wire Connector (E)
Lock Nut (D)
Mounting Plate (A)
Ball Nut (F) Rubber Pad (G)
----In 3H or 6H Mode, the light turns off completely, instead of low level brightness, after 3 minutes:
Make sure the low level is not at the 0% position.
-- The light blinks:
1. Make sure the light is not mounted near a barbecue, air conditioner or other heat source.
2. Adjust the sensitivity knob counterclockwise to avoid unnecessary triggering like a passing car or
reflecting objects.
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of
purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective
item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item (s)
is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item (s) is / are defective
as noted above. This warranty dose not cover labor costs, consequential damages, nor dose it apply to any item(s) that
have been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or emplyee(s).
Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance
deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale
or use of our products.We make no warranty, express or implied, and disclaim any warranty of merchantability or fitness
for a particular purpose.