Vaxcel T0130 Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0130 / T0134
Back Plate
Ball Nut (G)
Bulb Type A Max.60W
(not included)
Rubber Pad (H)
Parts:
141029
Mounting Screw (B) Green Grounding
Screw (C)
Lock Nut (F)
Wire Nut (E)
Cross Bar (A) Ball Nut (G)
Frame
Headless Screw (D) Rubber Pad (H)
Photocell
Rubber Pad
Fixture
Finial
Glass Panel
Cross Bar (A)
House Grounding Wire
Green Grounding Screw (C)
Fixture Grounding Wire
Wire Nut (E)
Outlet Box
Fixture Wire
Mounting Screw (B)
Lock Nut (F)
Headless Screw (D)
IMPORTANT:
The sensor has an excellent photocell function to
enable the light to turn on at dusk and off at dawn
automaticlly.
Turn off the power at the main fuse or circuit breaker box.
1. Thread two headless screws through the cross bar, then secure them with four lock nuts ( two on each side of the
cross bar). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level.
2. Attach the cross bar to the outlet box by using two mounting screws.
3. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follow:
---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Installation Steps

141029
--- Attach the fixture grounding wire (usually green insulation or bare wire) to the cross bar with the green grounding
screw. Then connect it to the house grounding wire with the wire nut.
Carefully put the wires back into the outlet box.
4. Attach the back plate to the cross bar by inserting the screws, then secure it with two rubber pads and ball nuts.
CAUTION: With silicone caulking compound, caulk completely around where the back side of the fixture
meets with the wall surface to prevent water from seeping into the outlet box.
5. Secure the finial onto the fixture tightly.
6. Install bulb (not included). See relamping label at socket area or packaging for maximum allowed wattage.
1. Turn off the power at the main fuse or circuit breaker box before starting installation.
2. Loosen the wire nuts connected with the wires from photocell. (See Fig.1)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire nuts: (See Fig.2)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
Photocell
White Wires From Photocell
Wire Nuts
Wires From Fixture
Wires From Fixture
Wires From
Main Power
Wire Nut
White Pigtail
Pigtail
Red Wires From Photocell
Black Wires From Photocell
Operation the Unit Without Photocell
Fig.1 Fig.2
Turn on the power at the main fuse or circuit breaker box.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Glass Panel
9652C
Mounting Screw (B) Green Grounding
Screw (C)
Lock Nut (F)
Wire Nut (E)
Cross Bar (A)
Ball Nut (G)
Headless Screw (D)
Rubber Pad (H)
Assembly Kit
5189MM (1 SET) for T0130
5190MM (1 SET) for T0134

141029
A: 12"
B: 6-1/2"
C: 6-1/4"