Vega VEGAPULS 62 User manual

Rhein Tech Laboratories, Inc. Client: VEGA Grieshaber KG
360 Herndon Parkway Models: VEGAPULS 61 / 62 / 63
Suite 1400 FCC ID: O6QPS60XK1
Herndon, VA 20170 Standard: FCC 15.209
http://www.rheintech.com Report Number: 2009282
Page 54 of 57
Appendix H: User Manual
Please refer to the following pages.

Operating Instructions
VEGAPULS 62
4…20 mA/HART two-wire
Document ID:
36503
Radar

Contents
1About this document
1.1Function.................................. 4
1.2Target group .............................. 4
1.3Symbolism used............................ 4
2For your safety
2.1Authorised personnel ........................ 5
2.2Appropriate use ............................ 5
2.3Warning about misuse ....................... 5
2.4General safety instructions . . . . . . . . . . . . . . . . . . . . 5
2.5CE conformity ............................. 6
2.6Fulfillment of NAMUR recommendations . . . . . . . . . . 6
2.7Radio approval for Europe . . . . . . . . . . . . . . . . . . . . 6
2.8Radio approval for USA/Canada . . . . . . . . . . . . . . . . 6
2.9Environmental instructions..................... 6
3Product description
3.1Configuration .............................. 7
3.2Principle of operation ........................ 8
3.3Packaging,transport and storage ............... 8
3.4Accessories and replacement parts . . . . . . . . . . . . . . 9
4Mounting
4.1General instructions ......................... 11
4.2Mounting preparations -Horn antenna . . . . . . . . . . . . 11
4.3Mounting preparations -Parabolic antenna. . . . . . . . . 12
4.4Mounting instructions ........................ 13
5Connecting to power supply
5.1Preparing the connection ..................... 25
5.2Connection................................ 26
5.3Wiring plan,single chamber housing . . . . . . . . . . . . . 28
5.4Wiring plan,double chamber housing . . . . . . . . . . . . 28
5.5Wiring plan with double chamber housing Ex d . . . . . 29
5.6Wiring plan -version IP 66/IP 68,1bar . . . . . . . . . . . 30
5.7Switch on phase............................ 30
6Set up with the indicating and adjustment module
6.1Insert indicating and adjustment module. . . . . . . . . . . 31
6.2Adjustment system .......................... 32
6.3Parameter adjustment........................ 33
6.4Saving the parameter adjustment data . . . . . . . . . . . . 41
7Setup with PACTware
7.1Connecting the PC .......................... 42
7.2Parameter adjustment with PACTware . . . . . . . . . . . . 43
7.3Saving the parameter adjustment data . . . . . . . . . . . . 44
2VEGAPULS 62 •4…20 mA/HART two-wire
Contents
36503-EN-100607

8Set up with other systems
8.1DD adjustment programs ..................... 45
8.2Communicator 375,475 ...................... 45
9Diagnosis and service
9.1Maintenance .............................. 46
9.2Measured value and event memory . . . . . . . . . . . . . . 46
9.3Status messages ........................... 47
9.4Rectify malfunctions ......................... 50
9.5Exchanging the electronics module . . . . . . . . . . . . . . 51
9.6Software update ............................ 51
9.7How to proceed in case of repair................ 52
10 Dismounting
10.1Dismounting steps .......................... 53
10.2Disposal ................................. 53
11 Supplement
11.1Technical data ............................. 54
11.2Dimensions ............................... 64
Safety instructions for Ex areas
Please note the Ex-specific safety information for installation and
operation in Ex areas.These safety instructions are part of the
operating instructions manual and come with the Ex-approved
instruments.
VEGAPULS 62 •4…20 mA/HART two-wire 3
Contents
36503-EN-100607

1About this document
1.1Function
This operating instructions manual provides all the information you
need for mounting,connection and setup as well as important
instructions for maintenance and fault rectification.Please read this
information before putting the instrument into operation and keep this
manual accessible in the immediate vicinity of the device.
1.2Target group
This operating instructions manual is directed to trained qualified
personnel.The contents of this manual should be made available to
these personnel and put into practice by them.
1.3Symbolism used
Information,tip,note
This symbol indicates helpful additional information.
Caution:If this warning is ignored,faults or malfunctions can
result.
Warning:If this warning is ignored,injury to persons and/or serious
damage to the instrument can result.
Danger:If this warning is ignored,serious injury to persons and/or
destruction of the instrument can result.
Ex applications
This symbol indicates special instructions for Ex applications.
lList
The dot set in front indicates a list with no implied sequence.
àAction
This arrow indicates a single action.
1Sequence
Numbers set in front indicate successive steps in a procedure.
4VEGAPULS 62 •4…20 mA/HART two-wire
1About this document
36503-EN-100607

2For your safety
2.1Authorised personnel
All operations described in this operating instructions manual must be
carried out only by trained specialist personnel authorised by the plant
operator.
During work on and with the device the required personal protective
equipment must always be worn.
2.2Appropriate use
VEGAPULS 62 is a sensor for continuous level measurement.
You can find detailed information on the application range in chapter
"Product description".
Operational reliability is ensured only if the instrument is properly used
according to the specifications in the operating instructions manual as
well as possible supplementary instructions.
2.3Warning about misuse
Inappropriate or incorrect use of the instrument can give rise to
application-specific hazards,e.g.vessel overfill or damage to system
components through incorrect mounting or adjustment.
2.4General safety instructions
This is a state-of-the-art instrument complying with all prevailing
regulations and guidelines.The instrument must only be operated in a
technically flawless and reliable condition.The operator is responsible
for the trouble-free operation of the instrument.
During the entire duration of use,the user is obliged to determine the
compliance of the required occupational safety measures with the
current valid rules and regulations and also take note of new
regulations.
The safety instructions in this operating instructions manual,the
national installation standards as well as the valid safety regulations
and accident prevention rules must be observed by the user.
For safety and warranty reasons,any invasive work on the device
beyond that described in the operating instructions manual may be
carried out only by personnel authorised by the manufacturer.Arbitrary
conversions or modifications are explicitly forbidden.
The safety approval markings and safety tips on the device must also
be observed.
VEGAPULS 62 •4…20 mA/HART two-wire 5
2For your safety
36503-EN-100607

Depending on the instrument version,the emitting frequencies are in
the Cor Kband range.The low emitting frequencies are far below the
internationally approved limit values.When used correctly,there is no
danger to health.
2.5CE conformity
The device fulfills the legal requirements of the applicable EC
guidelines.By attaching the CE mark,VEGA provides a confirmation
of successful testing.You can find the CE conformity declaration in the
download area of www.vega.com.
2.6Fulfillment of NAMUR recommendations
The device fulfils the requirements of the concerned NAMUR
recommendation.You can find detailed information in the download
section under www.vega.com.
2.7Radio approval for Europe
The instrument is approved according to EN 302372-2:2006-08 for
use in closed vessels.
2.8Radio approval for USA/Canada
This device complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:
lthis device may not cause harmful interference,and
lthis device must accept any interference received,including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the manufacturer
could void the user`s authority to operate the equipment.
This device complies with IC RSS-210.
This device is only allowed to operate within closed tanks or containers
made of metal,concrete or glass-fiber reinforced plastic.
2.9Environmental instructions
Protection of the environment is one of our most important duties.That
is why we have introduced an environment management system with
the goal of continuously improving company environmental protection.
The environment management system is certified according to DIN
EN ISO 14001.
Please help us fulfil this obligation by observing the environmental
instructions in this manual:
lChapter "Packaging,transport and storage"
lChapter "Disposal"
6VEGAPULS 62 •4…20 mA/HART two-wire
2For your safety
36503-EN-100607

3Product description
3.1Configuration
The type label contains the most important data for identification and
use of the instrument:
2
1
12
11
5
3
6
4
7
8
9
10
Fig.1:Structure of the type label (example)
1Instrument type
2Product code
3Approvals
4Electronics
5Protection rating
6Measuring range
7Process temperature,process pressure
8Material,wetted parts
9Hardware and software version
10 Order number
11 Serial number of the instrument
12 ID numbers,instrument documentation
The serial number on the type label of the instrument allows you to
have the order data,operating instructions manuals,sensor data for
the service DTM as well as the test certificate (depending on the
instrument)displayed via www.vega.com,"VEGA Tools"and "serial
number search".
This operating instructions manual applies to the following instrument
versions:
lHardware from 2.0.1
lSoftware from 4.1.0
The instrument is available in two different electronics versions:
The version in hand can be determined via the product code on the
type label as well as on the electronics.
lStandard electronics type PS60HK,modification status ≥22
Type label
Serial number
Scope of the operating
instructions manual
Versions
VEGAPULS 62 •4…20 mA/HART two-wire 7
3Product description
36503-EN-100607

lElectronics with increased sensitivity type PS60HS,modification
status ≥22
The scope of delivery encompasses:
lRadar sensor
lDocumentation
-this operating instructions manual
-Safety Manual (SIL)VEGAPULS 62 (optional)
-Operating instructions manual "Indicating and adjustment
module"(optional)
-Operating instructions "Radio module"(optional)
-Supplementary instructions manual "Heating for indicating and
adjustment module"(optional)
-Supplementary instructions manual "Plug connector for con-
tinuously measuring sensors"(optional)
-Ex-specific"Safety instructions"(with Ex versions)
-if necessary,further certificates
3.2Principle of operation
The version with "Horn antenna ø40 mm (1.575 in)"is particularly
suitable for small tanks and process vessels for measurement of
virtually all products.
The version with "Horn antenna ø48 …95 mm (1.89 …3.74 in)"is
particularly suitable for storage tanks and process vessels,for
measurement of products such as solvents,hydrocarbons and fuels
under most difficult process conditions.
The version with Parabolic antenna is particularly suitable for
measurement of products with low ε
r
value at great measuring
distances.
The electronics version with increased sensitivity enables the use of
the instrument also in applications with very poor reflective properties
or products with low ε
r
value.
The antenna of the radar sensor emits short radar pulses with a
duration of approx.1ns.These pulses are reflected by the product
and received by the antenna as echoes.The running time of the radar
pulses from emission to reception is proportional to the distance and
hence to the level.The determined level is converted into an
appropriate output signal and outputted as measured value.
3.3Packaging,transport and storage
Your instrument was protected by packaging during transport.Its
capacity to handle normal loads during transport is assured by a test
according to DIN EN 24180.
Scope of delivery
Application area
Functional principle
Packaging
8VEGAPULS 62 •4…20 mA/HART two-wire
3Product description
36503-EN-100607

The packaging of standard instruments consists of environment-
friendly,recyclable cardboard.For special versions,PE foam or PE foil
is also used.Dispose of the packaging material via specialised
recycling companies.
Transport must be carried out under consideration of the notes on the
transport packaging.Nonobservance of these instructions can cause
damage to the device.
The delivery must be checked for completeness and possible transit
damage immediately at receipt.Ascertained transit damage or
concealed defects must be reported.
Up to the time of installation,the packages must be left closed and
stored according to the orientation and storage markings on the
outside.
Unless otherwise indicated,the packages must be stored only under
the following conditions:
lNot in the open
lDry and dust free
lNot exposed to corrosive media
lProtected against solar radiation
lAvoiding mechanical shock and vibration
lStorage and transport temperature see chapter "Supplement -
Technical data -Ambient conditions"
lRelative humidity 20 …85 %
3.4Accessories and replacement parts
The indicating and adjustment module PLICSCOM is used for
measured value indication,adjustment and diagnosis.It can be
inserted into the sensor and removed at any time.
You can find further information in the operating instructions "Indicating
and adjustment module PLICSCOM"(Document-ID 27835).
The interface adapter VEGACONNECT enables the connection of
communication-capable instruments to the USB interface of a PC.For
parameter adjustment of these instruments,an adjustment software
such as PACTware with VEGA-DTM is required.
You can find further information in the operating instructions "Interface
adapter VEGACONNECT"(Document-ID 32628).
VEGADIS 61 is an external indicating and adjustment unit for sensors
with single chamber housing and double chamber housing Ex d.
Transport
Transport inspection
Storage
Storage and transport
temperature
Indicating and adjust-
ment module
Interface adapter
External indicating and
adjustment unit
VEGAPULS 62 •4…20 mA/HART two-wire 9
3Product description
36503-EN-100607

It is suitable for measured value indication and adjustment of plics®
sensors and is connected to the sensor with an up to 50 m long,four-
wire,screened standard cable.
You can find further information in the operating instructions
"VEGADIS 61"(Document-ID 27720).
VEGADIS 62 is suitable for measured value indication and adjustment
of sensors with HART protocol.It is looped into the 4…20 mA/HART
signal cable.
You can find further information in the operating instructions
"VEGADIS 62"(Document-ID 36469).
The PLICSMOBILE T 61 is an external GSM/GPRS radio unit for
transmission of measured values and for remote parameter adjust-
ment of plics®sensors.The adjustment is carried out via PACTware/
DTM by using the integrated USB connection.
You can find further information in the operating instructions
"PLICSMOBILE T 61"(Document-ID 32865).
The protective cover protects the sensor housing against soiling and
intense heat from solar radiation.
You will find additional information in the supplementary instructions
manual "Protective cover"(Document-ID 34296).
The electronics module VEGAPULS series 60 is a replacement part
for radar sensors of VEGAPULS series 60.Aseparate version is
available for each type of signal output.
You can find further information in the operating instructions
"Electronics module VEGAPULS series 60 "(Document-ID 36801).
The antenna impedance cone is used for optimum transmission of
microwaves and for sealing against the process.
You find further information in the operating instructions "Antenna
impedance cone VEGAPULS 62 and 68"(Document-ID 31381).
External indicating and
adjustment unit with
HART protocol
External radio unit
Protective cover
Electronics module
Antenna impedance co-
ne
10 VEGAPULS 62 •4…20 mA/HART two-wire
3Product description
36503-EN-100607

4Mounting
4.1General instructions
With instruments with threaded process fitting,suitable tools must be
applied for tightening the hexagon.
Warning:
The housing must not be used to screw the instrument in!Applying
tightening force can damage internal parts of the housing.
Use the recommended cables (see chapter "Connecting to power
supply")and tighten the cable gland.
You can give your instrument additional protection against moisture
penetration by leading the connection cable downward in front of the
cable entry.Rain and condensation water can thus drain off.This
applies mainly to outdoor mounting as well as installation in areas
where high humidity is expected (e.g.through cleaning processes)or
on cooled or heated vessels.
Make sure that all parts of the instrument exposed to the process,in
particular the antenna,seal and process fitting,are suitable for the
existing process conditions.These include above all the process
pressure,process temperature as well as the chemical properties of
the medium.
You can find the specifications in chapter "Technical data"or on the
type label.
4.2Mounting preparations -Horn antenna
The instrument is also available in versions where the antenna has a
bigger diameter than the process fitting (thread,flange). The antenna
must therefore be disconnected from the process fitting before
mounting.Proceed as follows:
1Loosen the hexagon screws (3)on the antenna socket with an
Allen wrench (size 3)
2Remove the antenna (4)
Note:
The plastic conemust not be pulled out of the antenna socket.
3Insert the antenna from below into the vessel socket and secure it
against falling off
4Retighten the antenna with hexagon screws to the antenna socket;
torque max.10 Nm(7.5lbf ft)
Screwing in
Moisture
Suitability for the pro-
cess conditions
VEGAPULS 62 •4…20 mA/HART two-wire 11
4Mounting
36503-EN-100607

Note:
The radar sensor with rinsing air connection or antenna extension is
provided with a notch on the antenna socket.This notch must
correspond to the marking on the hexagon of the process fitting (the
marking specifies the position of the polarisation level of the radar
signal).
3
4
1
2
Fig.2:Dismounting of the horn antenna
1Marking of the polarisation plane
2Notch at the antenna socket
3Hexagon screws on the antenna socket
4Antenna
4.3Mounting preparations -Parabolic antenna
The instrument is also available in versions where the antenna has a
diameter larger than the process fitting (thread,flange). With such
versions the antenna must be disconnected from the process fitting
before mounting.Proceed as follows:
1Clamp VEGAPULS 62 with the flange,e.g.in a bench vice
2Hold the connection piece (3)with a wrench (width across flats 22)
on the flattenings
3Loosen counter nut (2)completely with a wrench (width across
flats 36)in the antenna direction
4Loosen compression nut (1)completely with a wrench (width
across flats 41)in the antenna direction
5Remove the parabolic antenna (4)axially
6Mount sensor flange to the adapter flange and clamp it
7Check,if the O-ring seal is available on the connection piece and if
it is not damaged.
12 VEGAPULS 62 •4…20 mA/HART two-wire
4Mounting
36503-EN-100607

Note:
Adamaged O-ring seal must be replaced:FKM (Viton)article no.
2.28248,FFKM (Kalrez 6375)article no.2.27351
8Remount the parabolic antenna (4)
9Fasten compression nut (1)with a wrench (width across flats 41),
torque max.50 Nm
10 Fasten counter nut (2)with a wrench (width across flats 36), torque
max.40 Nm
Note:
Take note for the version with rinsing air connection that the holes in
the antenna and in the process fitting correspond.This ensures a
sufficient air flow (the air is led through the holes to the feed system.A
rinsing of the parabolic antenna in total is not intended).
1
2
3
4
Fig.3:Dismounting,parabolic antenna
1Compression nut
2Locknut
3Connection piece
4Parabolic antenna
4.4Mounting instructions
The illustrations with the following mounting instructions show a radar
sensor with horn antenna.The mounting instructions apply analo-
gously also to the version with parabolic antenna.
The emitted radar impulses of the radar sensor are electromagnetic
waves.The polarisation level is the direction of the electrical wave
component.By turning the instrument in the connection flange or
mounting boss,the polarisation can be used to reduce the effects of
false echoes.
The position of the polarisation plane is marked on the process fitting
of the instrument.
Horn and parabolic an-
tenna
Polarisation plane
VEGAPULS 62 •4…20 mA/HART two-wire 13
4Mounting
36503-EN-100607

1
1
Fig.4:Position of the polarisation level
1Marking hole
When mounting the sensor,keep a distance of at least 200 mm
(7.874 in)from the vessel wall.If the sensor is installed in the center of
dished or round vessel tops,multiple echoes can arise.However,
these can be suppressed by an appropriate adjustment (see chapter
"Setup").
If you cannot keep this distance you should carry out a false echo
storage before setup.This applies mainly if buildup on the vessel wall
is expected.In this case,we recommend repeating a false echo
storage later with existing buildup.
> 200 mm
(7.87
")
Fig.5:Mounting of the radar sensor on round vessel tops
In vessels with conical bottom it can be advantageous to mount the
sensor in the center of the vessel,as measurement is then possible
down to the lowest point of the vessel bottom.
Mounting position
14 VEGAPULS 62 •4…20 mA/HART two-wire
4Mounting
36503-EN-100607

Fig.6:Mounting of the radar sensor on vessels with conical bottom
Do not mount the instruments in or above the filling stream.Make sure
that you detect the product surface,not the inflowing product.
Fig.7:Mounting of the radar sensor with inflowing medium
The socket piece should be dimensioned in such a way that the
antenna end protrudes at least 10 mm (0.4in)out of the socket.
Inflowing medium
Socket
VEGAPULS 62 •4…20 mA/HART two-wire 15
4Mounting
36503-EN-100607

10 mm
>
Fig.8:Recommended socket mounting
If the reflective properties of the medium are good,you can mount
radar sensor on sockets which are higher than the length of the
antenna.You will find recommended values for socket heights in the
following illustration.The socket end should be smooth and burr-free,if
possible also rounded.After installation you must carry out a false
echo storage.
d
hmax.
d
1 "
50 mm/2"
80 mm/3"
100 mm/4"
150 mm/6"
200 mm
250 mm
300 mm
500 mm
800 mm
hmax.
Fig.9:Deviating socket dimensions
Tip:
The instrument is optionally also available with antenna extension.
Hence the antenna length can be selected such that the antenna end
protrudes 10 mm (0.4in)out of the socket.
In liquids,align the sensor as vertical as possible to the product
surface to achieve optimum measuring results.
Orientation of the sensor
16 VEGAPULS 62 •4…20 mA/HART two-wire
4Mounting
36503-EN-100607

Fig.10:Alignment in liquids
The mounting location of the radar sensor should be a place where no
other equipment or fixtures cross the path of the microwave signals.
Vessel installations,such as e.g.ladders,limit switches,heating
spirals,struts,etc., can cause false echoes and impair the useful echo.
Make sure when planning your measuring site that the radar sensor
has a "clear view"to the measured product.
In case of existing vessel installations,a false echo storage should be
carried out during setup.
If large vessel installations such as struts or supports cause false
echoes,these can be attenuated through supplementary measures.
Small,inclined sheet metal baffles above the installations scatter the
radar signals and prevent direct interfering reflections.
Fig.11:Cover smooth profiles with deflectors
If there are agitators in the vessel,a false signal suppression should be
carried out with the agitators in motion.This ensures that the interfering
reflections from the agitators are saved with the blades in different
positions.
Vessel installations
Agitators
VEGAPULS 62 •4…20 mA/HART two-wire 17
4Mounting
36503-EN-100607

Fig.12:Agitators
Through the action of filling,stirring and other processes in the vessel,
compact foams that damp the emitted signals considerably may form
on the product surface.
If foams are causing measurement errors,the biggest possible radar
antennas,the electronics with increased sensitivity or low frequency
radar sensors (Cband)should be used.
As an alternative,sensors with guided microwave can be used.These
are unaffected by foam generation and are best suited for such
applications.
When using a surge pipe in a vessel,influences from vessel
installations and turbulences can be excluded.Under these prereq-
uisites,the measurement of products with low dielectric values (ε
r
value ≥1.6)is possible.In very adhesive products,measurement in a
surge pipe is not recommended.
Foam generation
Measurement in a surge
pipe
18 VEGAPULS 62 •4…20 mA/HART two-wire
4Mounting
36503-EN-100607

0%
100%
1
2
3
1
2
3
4
5
8
6
7
9
Fig.13:Configuration surge pipe
1Radar sensor
2Marking of the polarisation plane
3Thread or flange on the instrument
4Vent hole
5Holes
6Weld joint
7Welding neck flange
8Ball valve with complete opening
9Fastening of the surge pipe
Instructions for orientation:
lNote marking of the polarisation plane on the sensor
lWith threaded fitting,the marking is on the hexagon,with flange
connection between the two flange holes
lThe marking must show to the direction of the holes in the surge
pipe
Instructions for the measurement:
lThe 100 %point must be below the upper vent hole and the
antenna edge
lThe 0%point is the end of the surge pipe
lFor the parameter adjustment,select "Application standpipe"and
enter the tube diameter to compensate errors due to running time
shift
lAfalse signal suppression with integrated sensor is recommended
but not mandatory
VEGAPULS 62 •4…20 mA/HART two-wire 19
4Mounting
36503-EN-100607