Vega B63-48 User manual

Operating Instructions
Overvoltage arresters
B63-48, B63-32
Document ID: 33012

2
Contents
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
Contents
1 About this document
1.1 Function ............................................................................. 3
1.2 Target group ....................................................................... 3
1.3 Symbolism used ................................................................. 3
2 For your safety
2.1 Authorised personnel ......................................................... 4
2.2 Appropriate use .................................................................. 4
2.3 Warning about incorrect use ............................................... 4
2.4 General safety instructions ................................................. 4
2.5 Safety label on the instrument ............................................ 4
2.6 CE conformity ..................................................................... 4
2.7 Safety instructions for Ex areas .......................................... 5
2.8 Environmental instructions ................................................. 5
3 Product description
3.1 Conguration ...................................................................... 6
3.2 Principle of operation .......................................................... 6
3.3 Packaging, transport and storage ....................................... 7
4 Instructions for installation
5 Connecting to power supply
5.1 Preparing the connection ................................................... 9
5.2 Connection procedure ........................................................ 9
5.3 Wiring plan ....................................................................... 11
6 Maintenanceandfaultrectication
6.1 Maintenance .................................................................... 12
6.2 Rectify faults ..................................................................... 12
6.3 Instrument repair .............................................................. 12
7 Dismounting
7.1 Dismounting steps ............................................................ 13
7.2 Disposal ........................................................................... 13
8 Supplement
8.1 Technical data .................................................................. 14
8.2 Dimensions ...................................................................... 15
Editing status: 2013-02-05

3
1 About this document
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
1 About this document
1.1 Function
This operating instructions manual provides all the information you
need for mounting, connection and setup as well as important instruc-
tionsformaintenanceandfaultrectication.Pleasereadthisinforma-
tion before putting the instrument into operation and keep this manual
accessible in the immediate vicinity of the device.
1.2 Target group
This operating instructions manual is directed to trained specialist
personnel. The contents of this manual should be made available to
these personnel and put into practice by them.
1.3 Symbolism used
Information, tip, note
This symbol indicates helpful additional information.
Caution: If this warning is ignored, faults or malfunctions can result.
Warning: If this warning is ignored, injury to persons and/or serious
damage to the instrument can result.
Danger: If this warning is ignored, serious injury to persons and/or
destruction of the instrument can result.
Ex applications
This symbol indicates special instructions for Ex applications.
• List
The dot set in front indicates a list with no implied sequence.
→ Action
This arrow indicates a single action.
1 Sequence
Numbers set in front indicate successive steps in a procedure.
Battery disposal
This symbol indicates special information about the disposal of bat-
teries and accumulators.

4
2 For your safety
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
2 For your safety
2.1 Authorised personnel
All operations described in this operating instructions manual must
be carried out only by trained specialist personnel authorised by the
plant operator.
During work on and with the device the required personal protective
equipment must always be worn.
2.2 Appropriate use
B63-48, B63-32 are overvoltage arresters in two-wire technology for
installation in VEGA level and pressure sensors.
Youcannddetailedinformationontheapplicationrangeinchapter
"Product description".
2.3 Warning about incorrect use
Inappropriate or incorrect use of the instrument can give rise to
application-specichazards,e.g.vesseloverllordamagetosystem
components through incorrect mounting or adjustment.
2.4 General safety instructions
This is a high-tech instrument requiring the strict observance of stand-
ard regulations and guidelines. The user must take note of the safety
instructionsinthisoperatinginstructionsmanual,thecountry-specic
installation standards as well as all prevailing safety regulations and
accident prevention rules.
Theinstrumentmustonlybeoperatedinatechnicallyawlessand
reliable condition. The operator is responsible for trouble-free opera-
tion of the instrument.
During the entire duration of use, the user is obliged to determine the
compliance of the necessary occupational safety measures with the
current valid rules and regulations and also take note of new regula-
tions.
2.5 Safety label on the instrument
The safety approval markings and safety tips on the device must be
observed.
2.6 CE conformity
ThisdevicefulllsthelegalrequirementsoftheapplicableECguide-
lines.ByattachingtheCEmark,VEGAprovidesaconrmationof
successfultesting.YoucanndtheCEconformitydeclarationinthe
download area of "www.vega.com".

5
2 For your safety
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
2.7 Safety instructions for Ex areas
PleasenotetheEx-specicsafetyinformationforinstallationandop-
eration in Ex areas. These safety instructions are part of the operating
instructions manual and come with the Ex-approved instruments.
2.8 Environmental instructions
Protection of the environment is one of our most important duties.
That is why we have introduced an environment management system
with the goal of continuously improving company environmental pro-
tection.Theenvironmentmanagementsystemiscertiedaccording
to DIN EN ISO 14001.
Pleasehelpusfulllthisobligationbyobservingtheenvironmental
instructions in this manual:
• Chapter "Packaging, transport and storage"
• Chapter "Disposal"

6
3 Product description
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
3 Product description
3.1 Conguration
The scope of delivery encompasses:
• Overvoltage arrester B63-48, B63-32
• Documentation
– this operating instructions manual
– Exspecicsafetyinstructionsand,ifnecessary,furthercerti-
cates
The following illustration shows the structure of B63-48, B63-32:
1
2
3
Fig. 1: Structure of B63-48, B63-32
1 Terminals for the signal cable input (unprotected side)
2 B63-48, B63-32
3 Signal cable output to the sensor (protected side)
3.2 Principle of operation
The overvoltage arresters B63-48, B63-32 are completely enclosed in
a stainless steel housing. They can be used for VEGA level and pres-
sure sensors in two-wire technology.
• Type B63-48 for 4 … 20 mA/HART sensors
• TypeB63-32forProbusPAandFoundationFieldbussensors
B63-48, B63-32 overvoltage arresters reduce any voltage surges that
may reach the signal cables to a harmless level. The devices contain
voltage-limiting components as well as gas conductors for bleeding
oimpulsesofupto10kAtoground.
Scope of delivery
Constituent parts
Application area
Functional principle

7
3 Product description
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
3.3 Packaging, transport and storage
Your instrument was protected by packaging during transport. Its
capacity to handle normal loads during transport is assured by a test
following ISO 4180.
The packaging of standard instruments consists of environment-
friendly, recyclable cardboard. For special versions, PE foam or PE
foil is also used. Dispose of the packaging material via specialised
recycling companies.
Transport must be carried out under consideration of the notes on the
transport packaging. Nonobservance of these instructions can cause
damage to the device.
The delivery must be checked for completeness and possible transit
damage immediately at receipt. Ascertained transit damage or con-
cealed defects must be appropriately dealt with.
Up to the time of installation, the packages must be left closed and
stored according to the orientation and storage markings on the
outside.
Unless otherwise indicated, the packages must be stored only under
the following conditions:
• Not in the open
• Dry and dust free
• Not exposed to corrosive media
• Protected against solar radiation
• Avoiding mechanical shock and vibration
• Storage and transport temperature see chapter "Supplement -
Technical data - Ambient conditions"
• Relative humidity 20 … 85 %
Packaging
Transport
Transport inspection
Storage
Storage and transport
temperature

8
4 Instructions for installation
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
4 Instructions for installation
B63-48, B63-32 overvoltage arresters are screwed into the position
of the cable gland on the sensor housing. The cable gland of the
sensor is screwed into the overvoltage arrester. No further assembly
is necessary.
Caution:
B63-48, B63-32 overvoltage arresters must not be used in a corrosive
environment.
The thread on the overvoltage arrester must correspond to the thread
on the sensor housing. In order to maintain the enclosure rating of the
sensor, PTFE gasket strip must be used. First of all, screw in by hand;
ifnecessary,usegreaseandnallytightenwitha½turnwithaSW27
wrench.

9
5 Connecting to power supply
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
5 Connecting to power supply
5.1 Preparing the connection
Always keep in mind the following safety instructions:
• Connect only in the complete absence of line voltage
Danger:
The stainless steel housing of B63-48, B63-32 has no electrical
function and therefore provides no internal or external connection to
groundorpotentialequalization.
The plant operator is responsible for ensuring an adequate connec-
tion, for example within the context of protective grounding, depend-
ing on the installation and protection rating.
The B63-48, B63-32 exhibit a voltage resistance of 0.5 kV for one
minute in the signal circuit with respect to the stainless steel housing,
but not with respect to the green/yellow cable in the sensor circuit.
This must be taken into account for the electrical installation.
Before starting setup make sure that the power supply corresponds to
thespecicationsonthetypelabel.
Inhazardousareasyoumusttakenoteoftherespectiveregulations,
conformityandtypeapprovalcerticatesofthesensorsandpower
supply units.
5.2 Connection procedure
Proceed as follows:
1. Unscrew housing cover of the sensor
2. If a display and adjustment module is present, remove it accord-
ing to the operating instructions of the sensor
3. Unscrew the cable gland
4. Push the connection cables through the cable gland into the sen-
sor
5. Screw B63-48, B63-32 into the opening of the cable gland ac-
cording to the description under "Mounting instructions"
6. Shorten the connection cables of B63-48, B63-32 to the suitable
length,stripothewireendsapprox.1cm(0.4in)
Note:
Toensureaneectiveovervoltageprotection,theconnectioncables
should be as short as possible. Unnecessary cable should not be
woundupandplacedinsidethesensorhousing.Thiscouldinuence
the protective function of B63-48, B63-32.
7. Connect wire ends red and black according to chapter "Wiring
plan" and operating instructions of the respective sensor
8. Connect wire end green/yellow to the internal ground terminal in
the sensor housing, connect external ground terminal to potential
equalisation
9. Pull out terminal block inside B63-48, B63-32 with pliers
Note safety instructions
Take note of safety
instructions for Ex
applications

10
5 Connecting to power supply
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
10. Push signal cables and screen through the cable gland and con-
nect according to chapter "Wiring plan" to the terminals
11. Check all cable connections, especially the ground connection, to
makesuretheyaretightenedsuciently
12. Insert terminal block into its position by using the pliers. A me-
chanical coding ensures the correct position
13. Screw cable gland into the thread of B63-48, B63-32, tighten
compression nut. The seal ring must completely encircle the
cable
I²C
Display
12 5678
Fig. 2: Overvoltage protection B63-48, B63-32 after installation and connection
14. Screw the housing cover back on
Theelectricalconnectionishencenished.

11
5 Connecting to power supply
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
5.3 Wiring plan
I²C
Display
1
12 5678
Fig. 3: Wiring plan, sensor side, example single chamber housing
1 Connection cables of B63-48, B63-32, wire assignment see chart
Terminals sensor Wire colour/Polarity
1Red(+)
2Black(-)
Ground terminal Green/yellow
12
-
G
+
Fig. 4: Wiring plan B63-48, B63-32-side
1 To the sensor
2 Signal circuit
Wiring plan

12
6Maintenanceandfaultrectication
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
6 Maintenanceandfaultrectication
6.1 Maintenance
If the instrument is used properly, no special maintenance is required
in normal operation.
To ensure the function of B63-48, B63-32, we recommend a regular
visual check at intervals of max. 1 year for:
• secure mounting
• mechanical damage or corrosion
• worn or otherwise damaged cables
• correct and clearly marked cable connections
6.2 Rectify faults
The operator of the system is responsible for taking suitable meas-
ures to rectify faults.
Therstmeasuretobetakenistochecktheinput/outputsignalas
well as the power supply. In many cases, the causes can be deter-
minedandfaultscanbequicklyrectied.
On-site repair of B63-48, B63-32 is not possible.
Should these measures not be successful, please call in urgent cases
the VEGA service hotline under the phone no. [phone].
The hotline is available to you 7 days a week round-the-clock. Since
weoerthisserviceworld-wide,thesupportisonlyavailableinthe
English language. The service is free of charge, only the standard
telephone costs will be charged.
Depending on the reason for the fault and the measures taken, the
steps described in chapter "Set up" may have to be carried out again.
6.3 Instrument repair
If a repair is necessary, please proceed as follows:
Youcandownloadareturnform(23KB)fromourInternethomepage
www.vega.com under: "Downloads - Forms and certicates - Repair
form".
By doing this you help us carry out the repair quickly and without hav-
ing to call back for needed information.
• Printandlloutoneformperinstrument
• Clean the instrument and pack it damage-proof
• Attach the completed form and, if need be, also a safety data
sheet outside on the packaging
• Please ask the agency serving you for the address of your return
shipment.You canndtherespectivecontactdataonourwebsite
www.vega.com under: "Company - VEGA worldwide"
Reaction when malfunc-
tions occur
Faultrectication
24 hour service hotline
Reaction after fault recti-
cation

13
7 Dismounting
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
7 Dismounting
7.1 Dismounting steps
Take note of chapters "Mounting" and "Connecting to power supply"
and carry out the listed steps in reverse order.
7.2 Disposal
The instrument consists of materials which can be recycled by spe-
cialised recycling companies. We use recyclable materials and have
designed the parts to be easily separable.
WEEE directive 2002/96/EG
This instrument is not subject to the WEEE directive 2002/96/EG and
the respective national laws. Pass the instrument directly on to a spe-
cialised recycling company and do not use the municipal collecting
points. These may be used only for privately used products according
to the WEEE directive.
Correctdisposalavoidsnegativeeectsonhumansandtheenviron-
ment and ensures recycling of useful raw materials.
Materials: see chapter "Technical data"
If you have no way to dispose of the old instrument properly, please
contact us concerning return and disposal.

14
8 Supplement
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
8 Supplement
8.1 Technical data
General data
Version The device can be screwed into the sensor housing
instead of the cable gland
Housing material 316Ti
Weight approx. 175g(0.385lbs)
Electrical characteristics1)
Leakage current at nominal voltage < 10 µA
Internal resistance 1Ω
Nominal leakage current <10kA(8/20µs)
Band width 1MHz
Signal circuit
Nominal voltage/Signal
ƲB63-48 9 … 48 V DC/4 … 20 mA/HART
ƲB63-32 9…VDC,ProbusPA,FoundationFieldbus
Screw terminals for cable cross-section <1mm²(AWG18)
Sensor circuit
Number of wires two signal cables, one ground cable
Wire cross-section 1.5mm²(AWG14)
Cable length 250mm(9.843in)
Ambient conditions
Ambient temperature -40…+85°C(-40…+185°F)
Storage and transport temperature -40…+85°C(-40…+185°F)
Moisture 5…+95°%(non-condensing)
Electrical protective measures
Protection in assembled and connected
state
IP 66
Approvals
Instrumentswithapprovalscanhavedierenttechnicaldatadependingontheversion.
For that reason the associated approval documents of these instruments have to be carefully
noted. They are part of the delivery or can be downloaded under www.vega.com via "VEGA Tools"
and "serial number search" as well as via "Downloads" and "Approvals".
1) Reference temperature 25 °C (77 °F).

15
8 Supplement
Overvoltage arresters • B63-48, B63-32
33012-EN-130228
8.2 Dimensions
76 mm
(2.99")
SW 27 mm
(1.06")
56 mm
(2.21")
250 mm
(9.84")
1
Fig. 5: Dimensions B63-48, B63-32
1 Thread M20 x 1.5 or ½ NPT, depending on order specication

Printing date:
VEGA Grieshaber KG
Am Hohenstein 113
77761 Schiltach
Germany
33012-EN-130228
All statements concerning scope of delivery, application, practical use and operat-
ing conditions of the sensors and processing systems correspond to the information
available at the time of printing.
Subject to change without prior notice
© VEGA Grieshaber KG, Schiltach/Germany 2013
Phone [phone]
Fax [phone]
E-mail: [email protected]
www.vega.com