Vent-Axia HR200V User manual

HR200V
Ducted
Heat Recovery Ventilator
Installation and Maintenance Instructions
PLEASEREADINSTRUCTIONSINCONJUNCTIONWITH
ILLUSTRATIONS.PLEASESAVETHESEINSTRUCTIONS
Stock Ref No:-
HR200V 14120010

IMPORTANT SAFETY INFORMATION
PLEASE READ THESE
INSTRUCTIONS CAREFULLY
BEFORE COMMENCING
INSTALLATION.
1. Do not install this product in areas where the
following may be present or occur:
• Excessive oil or a grease laden atmosphere.
• Corrosive or flammable gases, liquids or vapours.
• Subject to direct water spray from hoses.
• Ambient temperatures higher than 40°C and lower
than -20°C.
• Possible obstructions that may hinder access to or
removal of the unit.
2. All wiring must be in accordance with the current
IEE wiring regulations BS7671, or appropriate
standards of your country. Installation should be
inspected and tested by a suitably qualified person
after completion.
3. Ensure the mains supply (voltage, frequency and
phase) complies with the rating label.
4. The unit should be provided with a local double
pole fused spur fitted with a 3A fuse having a contact
separation of at least 3mm.
5. These units must be earthed.
6. Precautions must be taken to avoid the back-flow
of gases into the building from the open flue of gas or
other fuel-burning appliances.
7. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
8. Young children should be supervised to ensure
that they do not play with the appliance.
INSTALLATION GUIDANCE
1. The installer is responsible for the installation and
electrical connection of the sentinel system on site. It
is the responsibility of the installer to ensure that the
equipment is safely and securely installed and left
only when mechanically and electrically safe.
2. All regulations and requirements must be strictly
followed to prevent hazards to life and property, both
during and after installation, and during any
subsequent servicing and maintenance.
3. The unit’s condensate drain must be connected to
the building’s wastewater drainage system.
4. Certain applications may require the installation of
sound attenuation to achieve the sound levels
required.
5. The unit must not be connected directly to a
tumble drier.
6. The supply and exhaust valves must be fully
opened prior to commissioning.
7. The supply air must be drawn from the exterior of
the property.
8. The unit should be allowed to stabilise during
commissioning for a minimum period of 5 minutes
when changing between boost and normal speeds.
9. Ensure that the unit’s external grilles are a
minimum of 1500mm apart. The exhaust grille should
be located at least 600mm away from any flue outlet.
The inlet grille should be located 2000mm away from
any flue outlet.
10. This product and associated duct installation
should be carried out in accordance with the
domestic ventilation compliance guide.
Disposal
This product should not be disposed of
with household waste. Please recycle
where facilities exist. Check with your
local authority for recycling advice.

3
Warnings & Safety Information

Contents
Section Page
1.0 Introduction 4
2.0 Site Requirements 5
3.0 Installation 6
4.0 Electrical 8
5.0 Maintenance 9

4
1.0 Introduction
1.1 Description (Fig. 1)
1. The HR200V unit is a void mounting heat
recovery ventilator for sealed or internal rooms in
domestic, commercial, educational and leisure
applications.
2. The HR200V is designed for connection to
150mm diameter standard flexible or rigid
ventilation ducting.
3. The maximum power consumption for the unit
is 108w.
4. The twin impeller and heat exchanger
arrangement simultaneously supplies and
extracts air while transferring heat from the stale
exhaust airflow to the fresh intake airflow. This
provides up to 70% heat recovery from the stale
extracted air.
1.2 Ancillary Equipment
1. The HR200V unit can be used in conjunction
with a range of ancillary equipment.
Controller: A range of controllers - see section
3.1 Controllers.
Fig. 1

5
2.0 Site Requirement
2.1 Information
1. The unit is designed for mounting in a ceiling
void and connected to inlet and outlet grilles with
150mm diameter ducting. Dimensions of the unit
are shown In Fig.1.
2. Warning: This appliance is class I and it
must therefore be earthed.
3. The unit must be sited and connected by a
suitably competent person and be in accordance
with current UK Building Regulations and I.E.E.
Wiring Regulations (BS 7671).
4. The unit is intended for permanent connection
to the mains electrical supply.
5. The unit is intended for fixed wiring installation.
6. Wiring to the unit in the UK must be via a
switched fused spur. The switched fused spur
must have a 3mm minimum contact gap in all
poles.
7. Ensure that the mains electrical supply is
compatible with the rating label attached to the
product.
8. The unit must be sited such that the ambient
temperature will not exceed 40° C.
9. Do not site the appliance in the vicinity of
excessive levels of airborne oil or grease.
10. If the unit is installed in a room containing a
fuel burning appliance, the installer must ensure
that air replacement is adequate for both
appliances.
11. The unit must be installed away from any source of
water and out of reach of any person using a fixed bath or
shower.
12. In situations where moisture can be present
in the air, the unit should be connected to a
drainage system.
13. The external grilles of the unit must be sited
at least 600mm away from any flue of gas or
solid fuel appliances. This is to avoid back flow of
gases entering the room.
14. All safety regulations and requirements must
be strictly followed to prevent hazards to life and
property both during and after installation and
during subsequent maintenance or servicing.
15. Ensure the mains electrical supply is switched
off before commencing installation or
maintenance.
Fig. 2