Verano Mallorca Special V150 User manual

INSTALLATION MANUAL
DROP-ARM AWNING
V150 - MALLORCA SPECIAL

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
1
Subject to misprints, errors and technical modifications.
Content
1. Drop-arm awning *
2. Control
a. Manual control: crank handle
b. Manual control: strap coiler
c. Electrical control: switch + plug
d. Remote control: remote control + plug
* Depicted awning has manual control
Necessary tools
• Drilling machine
• Masonry drill
• Crosshead screwdriver
• Socket wrench 10/13/17
• Allen key set
• Rattle with extension piece, cap 10/17 mm
• Tapeline
• Level
• Pencil
In case of electrical control:
• Shears
• Flathead screwdriver
2
1

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
2
Subject to misprints, errors and technical modifications.
Important before installation
Be careful for damages
Don’t use a knife or any other sharp object when opening the packing. This may cause damage to the content
of the package.
Put the content of the package on a so surface. Be careful when drilling, falling drill cuttings can cause damages.
Check if the window frame or façade is at and smooth.
General warning
Installing the Verano® product yourself is at your own risk. Only use this instruction as a tool and for the installation
of this specic Verano® product.
If you cannot install the product yourself, you can always opt for professional installation. The installation team
of Verano® is pleased to help you.
Specications V155 - Mallorca Speciaal
20
40
20
26
110
60 24
6
10
110
106
116
wall support awning cross section
Installation
Width (B)
minimal 2000 mm maximal 8000 mm
Measurements in mm

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
3
Subject to misprints, errors and technical modifications.
1.1 Marking the holes for the wall supports
The wall supports need to be installed 10 cm to 15 cm from the ends (g 1.1).
Optional remaining wall supports need to be divided equally between the two outer wall supports.
Mark the drill holes of the wall supports to the wall (A). They need to be aligned level, both horizontal and vertical.
See gure 1.2. Make sure that both the installation holes for the wall supports are in the middle of the stone.
See gure 1.3. If necessary, use an align-cord.
g. 1.2 Placement of the wall supports
g. 1.1 Marking the holes for the wall supports
A
muursteun
A
muursteun
X
1. Installation of the wall supports
X = Width of the awning
Y = Installation height (from the ground)
A = Wall supports
X
Y
AA
X = Width of the awning
wall support wall support

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
4
Subject to misprints, errors and technical modifications.
1.3 Drilling the hole for control
1. Carefully mark the extension hole where the cable or strap needs to go inside for the control.
- Cable: the hole needs to be exactly at the same height as where the cable comes out of the box.
- Strap: minimally 50 mm below the box, straight beneath the location where the strap comes out of the box.
2. Drill the hole for the wall lead-through.
Before drilling, check if there are no pipes or other obstacles in the wall. Always use a shelf inside the wall
to prevent damages to the plaster.
- Lead-through for the pull-up strap: 20 mm (drill 10 mm, aer that 20 mm).
- Lead-through for electrical cable: 10 mm.
g. 1.3 Installation of the wall support
1.2 Drilling the holes
Drill the installation holes. Use matching, high quality plugs
and bolts (standard A2 or for a sea climate A4). Install the
awning to the wall and xate the bolts. See gure 1.3.
1.4 Extra wall supports with a weak wall
If there are less than 5 stones above the installation location, an extra wall support is needed. This extra wall
support divides the power over a bigger wall surface, this way the wall can carry more weight. See gure 1.4.
extra
g. 1.4 Application of extra wall supports

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
5
Subject to misprints, errors and technical modifications.
2.1 Installation of the awning with manual control (outside)
Hang the awning in the wall supports. See gure 2.1 and 2.2. Proceed with step 2.3 “Securing the awning”.
2. Installation of the awning
g. 2.2 Detail wall support
g. 2.1 Hang the awning (outside control)

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
6
Subject to misprints, errors and technical modifications.
2.2 Drilling the hole for control
1. Carefully mark the extension hole where the cable or strap needs to go inside for the control.
- Cable: the hole needs to be exactly at the same height as where the cable comes out of the box.
- Strap: minimally 50 mm below the box, straight beneath the location where the strap comes out of the box.
2. Drill the hole for the wall lead-through.
Before drilling, check if there are no pipes or other obstacles in the wall. Always use a shelf inside the wall
to prevent damages to the plaster.
- Lead-through for the pull-up strap: 20 mm (drill 10 mm, aer that 20 mm).
- Lead-through for electrical cable: 10 mm.
2.3 Installation of the awning with inside control
3. Hang the awning in the wall supports. See gure 2.3 or electrical control or 2.4 for strap control.
4. Cable: lead the electrical cable inside through the drill lead-through hole.
Strap: install the strap guide to the wall support with the pulley on top.
Guide the strap inside through the strap guide and the drilled lead-through hole.
1
band
2
snoer
1
band
2
snoer
g. 2.3 Hanging a motorized awning g. 2.4 Hanging an awning with inside strap control
Cable Strap

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
7
Subject to misprints, errors and technical modifications.
2.4 Securing of the awning
1. Secure the wall supports using the included bolts. The bolts need to be applied manually. If this is not possible,
the wall supports are nog aligned well! Attention! The awning may not be opened before the securing bolts
are in place!
g. 2.6 Applying the securing bolts

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
8
Subject to misprints, errors and technical modifications.
3.1 Marking the holes for the drop-arms
Mark the drop-arms following the drawing below. The drop-arms need to be placed in one line. If the positions
of the drop-arms are not levelled, the awning will not function well. The pictured sizes are the minimal sizes that
the drop-arm needs to fall inside the drop-arm awning.
3.2 Drilling the holes
Drill the installation holes. We advise to use a masonry drill if the wall is made of stone or concrete. Use matching,
high quality plugs and bolts (standard A2 or for a sea climate A4). Install the drop-arm to the wall by rst xing it on
the bottom side (g 3.2).
Remove the tape from the arm (g 3.3). Attention! The arm is under tension and will unfold immediately!
Fixate the top side(3.4).
3. Installation of the drop-arms
g. 3.1 Measuring the drop-arms
g. 3.2 Fixate the bottom of the drop-arm g. 3.3 Remove the tape g. 3.4 Fixate the top of the drop-arm
Control side
Manual outside: 48 mm
Manual inside: 13 mm
Electrical: 13 mm
Projection + 60 mm =
Bottom arm guide
13 mm

INSTALLATION MANUAL
DROP-ARM AWNING V150 - MALLORCA SPECIAL
13227648-190830EN
9
Subject to misprints, errors and technical modifications.
3.3 Setting the sheets to the arms
Slide the sheets in the ends of the arms. Make sure that the sheets are faced downwards (g. 3.5).
Fixate the sheets with the included screws (g. 3.6)
3.4 Fixing the arms to the front bar
Turn the drop-arm up (g 3.7) Attention! The arm is under pressure.
Screw the drop-arm to the xing plate in the front bar (g. 3.8).
Repeat these steps for all arms.
g. 3.5 Sheet in the arms
g. 3.7 Folding back the drop-arm
g. 3.6 Fixating of the sheets
g. 3.8 Fixating the drop-arm