Verano V480 Cannes User manual

INSTALLATION MANUAL
AWNING V80 - CANNES

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
1
Subject to misprints, errors and technical modifications.
* The pictured awning is motorized.
Content
1. Awning *
2. Wall supports
3. Extra support(s) (with an awning bigger than 350 cm)
4. Mounting plates (optional)
5. Control
a. Manual operation: Crank handle
b. Electrical: Switch and plug
c. Remote controlled: Remote control and plug
1
2
3
2
4
4
4
Necessary tools
• Drilling machine
• Masonry drill 10/14 mm
• Crosshead screwdriver
• Socket wrench 17
• Allen key 6
• Tapeline
• Level
• Pencil
In case of electrical control:
• Nippers
• Flathead screwdriver

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
2
Subject to misprints, errors and technical modifications.
Specications V480 Cannes
150 12
10
172
172
240
240
45 45
90
45 80 28
153
15
20
150 12
10
172
172
240
240
45 45
90
45 80 28
153
15
20
150 12
10
172
240
45 45
90
45 80 28
153
15
20
Front view wall support
Wall mounting
Ceiling installation Integrated lighting included
Awning section
Awning section Awning section
Sizes in mm
Overview wall supports
0 / 0 / 2 0 / 0 / 2 0 / 0 / 2 0 / 0 / 3 0 / 0 / 3 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 6 0 / 0 / 6 0 / 0 / 6 0 / 0 / 8 0 / 0 / 8 0 / 0 / 8
0 / 0 / 2 0 / 0 / 2 0 / 0 / 2 0 / 0 / 3 0 / 0 / 3 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 6 0 / 0 / 6 0 / 0 / 6 0 / 0 / 8 0 / 0 / 8 0 / 0 / 8
- 0 / 0 / 2 0 / 0 / 2 0 / 0 / 3 0 / 0 / 3 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 4 0 / 0 / 6 0 / 0 / 6 0 / 0 / 6 0 / 0 / 8 0 / 0 / 8 0 / 0 / 8
- - 0 / 0 / 2 0 / 2 / 1 0 / 2 / 1 0 / 2 / 2 0 / 2 / 2 0 / 2 / 2 0 / 2 / 2 0 / 3 / 3 0 / 4 / 2 0 / 4 / 2 0 / 4 / 4 0 / 4 / 4 0 / 4 / 4
- - - 0 / 2 / 1 0 / 2 / 1 0 / 2 / 2 0 / 2 / 2 0 / 2 / 2 0 / 2 / 2 0 / 3 / 3 0 / 4 / 2 0 / 4 / 2 0 / 4 / 4 0 / 4 / 4 0 / 4 / 4
- - - - 2 / 0 / 1 2 / 0 / 2 2 / 0 / 2 2 / 0 / 2 2 / 0 / 2 3 / 0 / 3 3 / 0 / 3 4 / 0 / 2 4 / 0 / 4 4 / 0 / 4 4 / 0 / 4
Type 300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
300 / 180
/ 90
1500
2000
2500
3000
3500
4000
Pro-
jection
[mm]
Width [mm]
All
Fabric
type
Fabric
length
[mm]
Required number of wall supports
2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 8000 9000 10000 11000 12000
All

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
3
Subject to misprints, errors and technical modifications.
Important before mounting
1
2
3
4
5
rollaag
min. 30 cm
Patio door
When the awning is fully open, it hangs down under the angle. Therefore we advise to keep at least 30 centimeters
between the window frame and the awning in a situation with patio doors to the outside. When possible, it is advisable to
hang the awning higher than 30 centimeters above the window frame.
General warning
Installation of the Verano® product yourself is at your own risk. Only use this instruction as a tool and for the installation
of this specic Verano® product. If you cannot install the product yourself, you can always opt for professional installation.
The installation team of Verano® is pleased to help you.
Be careful for damages
Don’t use a knife or any other sharp object when opening the packing. This may cause damage to the content of the
package. Put the content of the package on a so surface. Be careful when drilling, falling drill cuttings can cause damages.
Check for a plane window frame or façade.
Check the installation height
Make sure that you have enough installation height on your façade to place the awning. Above the wall support
(mounting support) have to be 5 rows of stones to prevent to much pressure on the façade. This is not oen the case with
a house-extension. It is recommended to drill the installation hole in the h stone (minimum) measured from the top.
Wall strips
When there are fewer than ve rows of stones above the wall support, wall strips have to be used. These strips divide the
forces over a bigger wall surface when the walls are to weak. View page 5 for extensive instructions.
Attention! Make sure there is no installation point in the soldier course. These are oen half stones.
Soldier course

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
4
Subject to misprints, errors and technical modifications.
1.1 Marking the holes
View the stickers on the back side of the awning. See gure 1.1.
The heart of the wall supports needs to be placed where the stickers are located.
The heart of the wall supports needs to be installed at the same height as the stickers.
Mark the drill holes on the wall. If the number of delivered wall supports is larger than the number of arms (red sticker) in
the awning, you need to divide the other wall supports equally over the width of the awning.
The wall supports need to be levelled, both horizontal and vertical. See gure 1.2. If necessary, use a cord to level.
Make sure that the drill holes are mostly in the middle of the stone. See gure 1.3.
g. 1.2 Placing the wall supports
g. 1.1 Location stickers
centersticker sticker
X
1. Installation of the wall supports
W = Width of the awning
Y = Window frame height plus a minimum of 30 cm
A = Wall supports
B = Center support (used with awnings wider than 350 cm)
X
Y
ABA
X = Breedte van het scherm

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
5
Subject to misprints, errors and technical modifications.
1.3 Drilling the control hole
If you want to connect your wall control on the inside, measure the place of the control hole carefully. This depends on
your personal preference and situation.
Drill inwards with a 10 millimeter drill. When drilling through the wall, it is advisable to place a shelf against the inner side
of the wall to prevent damages to the wall.
g. 1.3 Installation wall support and mounting plate (optional)
1.2 Drilling the holes
Drill the installation holes. Our advise is to drill with
a 14 millimeter masonry drill in case of a wall made
of concrete or stone. Use matching plugs and bolts of
high quality. (our advice 14 mm plug, 10-12 mm bolt).
Install the wall supports and tighten the bolts.
Optionally, use installation plates if the wall is uneven.
See gure 1.3.
1.4 Extra wall support weak wall
If there are less than ve rows of stones above the installation location, extra wall supports are needed.
The extra wall supports divide the power over a larger wall surface. This way the wall can carry more weight.
See gure 1.4.
extraextra
g. 1.4 Applying extra wall supports

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
6
Subject to misprints, errors and technical modifications.
2.1 Placing the awning
1. Hang the awning in the wall supports. See gure 2.1.
Attention! Only loosen the long allen bolts (a) in the lower part of the wall support, don’t fully unscrew!
2. Lay the awning in the lower hook (arrow 1) of the wall support and push it backwards (arrow 2) until all the
wall supports are hooked to the awning.
3. Screw the long allen bolts (a) in de lower part of the awning and make sure that the awning can not be loosened
from the wall supports.
2. Installation of the awning
a
1
2
a
g. 2.1 Placing the awning

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
7
Subject to misprints, errors and technical modifications.
3. Electrical wall control
TIP! Sealing the hole
In case of an electrical wire to the inside, we advise to seal the hole where the wire comes in. This to prevent moisture from
running inwards. Attention! Do this both on the in- and outside.
3.2 Standard factory setting
The motor control is set standardly.
See the included manual of the motor and the possible remote control.
g. 3.1 Motor le (seen from the outside) g. 3.2 Motor right (seen from the outside)
3.1 Connecting the wall control
1. Check the position of the motor (le or right), seen from the outside!
2. If you have inside control, rst guide the cable through the hole in the wall you drilled before.
3. Connect the four-wired cord of the motor and the three-wired cored with plug following the scheme below.
4. Put the plug in the power point.
5. The awning is now connected. Before you continue the installation, check if the awning rolls out correctly.
yellow/green
blue
brown
yellow/green
blue black
brown brown
yellow/green
blue brown
yellow/green blue
black brown brown
yellow/green
blue
brown
yellow/green
blue black
brown brown
yellow/green
blue brown
yellow/green blue
black brown brown
brown
brown
brown brown brown brown black black
blue blue
blue blue
yellow/green yellow/green yellow/green yellow/green

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
8
Subject to misprints, errors and technical modifications.
4.1 Connecting the remote control
1. If the power point is located on the inside, rst guide the wire through the hole in the wall you drilled before.
2. Install the plug according to the color scheme below:
Brown 220V power supply
Blue 220V power supply
Yellow/green grounding
Black (do not connect)
White (do not connect)
Orange (do not connect)
3. Put the plug in the power point.
4. The awning is now connected. Before you continue the installation, check if the awning rolls out correctly by using the
remote control.
TIP! Sealing the hole
In case of an electrical wire to the inside, we advise to seal the hole where the wire comes in. This to prevent moisture
from running inwards. Attention! Do this both on the in- and outside.
4. Remote control

INSTALLATION MANUAL AWNING V480 - CANNES
13593589-190913EN
9
Subject to misprints, errors and technical modifications.
1 2
3
1
2 3
5.1 Standard factory setting
The passage height for the front bar is standard set between 1,80 and 1,90 meter at an installation height of 2,70 meter.
5.2 Setting the pitch
If you want to set the awning dierent from the standard factory setting, please follow the steps below:
1. Completely roll out the awning. The arm-connections are located le and right at the beginning of the folding arms
(on the side of the box). See gure 5.1.
2. Loosen nut #1 with one stroke (wrench 17). Unscrew hexagon-head bolt #1 in one turn (socket wrench 17).
3. Unscrew allen screw #2.
4. Turn allen screw #3 clockwise to lower the arm and to li it anti-clockwise. During the turning, li the front bar to
move allen screw #3 easily.
5. Set both arms until the desired slope is reached and the front bar is levelled.
6. Secure everything by screwing allen screw #2 and hexagon-head bolt #1.
7. If the elbow of the arm is to high, loosen hexagon-head bolt #1.
Attention! Never touch the nut with a red cross.
g. 5.1 Detail le arm-connection
5. Pitch