Vertiv Liebert GXTRT-1000IRT2UXL User manual

LIEBERT® GXT RT+ UPS
I, 230V, 1,000 - 3,000 VA
Quick Installation Guide
SL-28301_REV0_11-19 1
I M P O R TA N T: Before installing,
connecting to supply or operating
your Liebert GXT RT+ UPS, please
review the Safety and Regulatory
Statements sheet. For detailed
installation, operating, maintenance
and troubleshooting information
refer to the GXT RT+ User Guide for
your model available at
www.Vertiv.com.
Thank you for your recent purchase of a Vertiv UPS! We appreciate your
business and are condent that your new product will provide many years
of uninterruptible power to your connected equipment. With this
purchase, you may also want to consider Vertiv’s complete line-up of
Racks, PDU’s, Thermal Solutions, KVM Switches, and Serial Consoles.
Vertiv also oers a broad array of Services and Extended Warranties. If
you require any support, please don’t hesitate to reach out to Vertiv or
one of our Resellers or Local Rep Firms. We stand ready to support you.
We sincerely hope that you’ll continue to select Vertiv for all of your future
infrastructure needs!
The Vertiv Team
MODEL DESIGN CONFIGURATIONS
GXT RT+ UPS
#Description
1AC Input
2Input circuit breaker
3USB communication port
4RS-232 communication port
5SNMP intelligent slot (option)
6External battery connection
7Output receptacles
GXTRT-1000IRT2UXL GXTRT-1500IRT2UXL
GXTRT-2000IRT2UXL
GXTRT-3000IRT2UXL

LIEBERT® GXT RT+ UPS 230V 1,000 - 3,000 VA
Quick Installation Guide
2 SL-28301_REV0_11-19
INSTALLATION
1. Inspecting the UPS
Inspect the UPS for any signs of
obvious damage. If damage is
visible, do not proceed and call
our warranty support line for
assistance at 0080011554499
(Toll free), [phone]
(Toll), or email at eoc@vertiv.
com .
2. Choosing a location
Install the UPS in a temperature-
controlled environment that is
free of corrosive and conductive
contaminants. Avoid locations
near heat or water sources and
exposed to direct sunlight.
For proper ventilation, leave 100
mm clearance on all sides of the
UPS.
The input outlet should be
nearby and easily accessible.
3. Installing the UPS
The UPS and optional External
Battery Cabinets may be installed
in either a tower or rack
conguration.
• For tower installation, assemble
and attach the tower support
stands and spacers.
• For rack installation:
1. Attach the handles to the
UPS.
2. Install the rail kit in the rack.
NOTE: Align shelf of rack kit
with rack U number for proper
alignment.
3. Install the UPS in the rack.
4. Secure the handles to the
rack.
• After UPS installation, install
internal batteries shipped in
separate box.
CONNECTIONS
4. Connecting External
Battery Cabinet (Optional)
External Battery Cabinets (EBC)
provide longer battery run-time
for connected devices. Refer to
GXT RT+ User Guide to select
the appropriate model and
quantity for your GXT RT+ model
and applications.
• Verify that the EBC breaker is
in the “O” position.
• Connect one end of the
supplied EBC cable to the UPS
and one end to the battery
cabinet. If connecting more
than one external battery,
connect one end of the
external battery cable to the
second connector on the
battery cabinet, then connect
the other end to the next
battery cabinet.
• Verify that the EBC breaker is
in the “On” position.
5. Connecting AC Input
The UPS is cord and plug
connected using an IEC 60320-1
input plug. Perform all wiring in
accordance to all local and
national electrical codes.
The UPS is equipped with output
receptacles. Connect the
equipment to be protected to
the output receptacles.
NOTE: Allow the batteries to charge
at-least 5 hours before rst start-up
to ensure adequate back-up time.
The batteries charge when the UPS
is connected to AC input regardless
of the o/on status of the UPS.
WIRING
Model Recommended External Breaker
GXTRT-1000IRT2UXL
GXTRT-1500IRT2UXL
GXTRT-2000IRT2UXL
10 A
GXTRT-3000IRT2UXL 20 A

LIEBERT® GXT RT+ UPS 230V 1,000 - 3,000 VA
Quick Installation Guide
SL-28301_REV0_11-19 3
Operation and Display Panel
POWERING THE UPS
NOTE: Do not start the UPS until
the installation is nished, the
system is commissioned by an
authorized engineer, and the
external input circuit breakers are
closed.
1. Make sure the breaker supplying
power to the UPS is closed, and
close the input breaker on the
rear of the UPS.
2. If necessary, use the LCD display
to make any required settings.
(Refer to the User Guide for
conguration set up.)
3. Close all output breakers on the
rear of the UPS (or in an external
panel board, if used).
4. If external battery cabinets are
included, close the breakers on
the rear of each cabinet.
5. Power-on the UPS using the
Operation and Display Panel by
pressing and holding the power
button.
NOTE:During operation, the UPS
may sound an alarm as the output
receptacles are powered. You may
press the power/mute button for 5
seconds to silence the audible alarm.

To contact Vertiv Technical Support: visit www.Vertiv.com
© 2020 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. All other names and logos referred to are
trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness here, Vertiv Group Corp.
assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specications, rebates and other promotional
oers are subject to change at Vertiv’s sole discretion upon notice.
4 SL-28301_REV0_11-19