Vertiv Liebert PSA User manual

Quick-Start Guide - 1000VA/1500VA, 230V
UPS Status, Alarm Conditions and Alerts
Audible AlarmSolid/FlashingColorLEDCondition
Overload LED 3 Amber Solid (steady glow) until load drops or breaker trips Continuous
Battery Low LED 2 Amber Flashes every 1 second till end of discharge (EOD) Every 1 second
Battery Mode LED 2 Amber Flashes every 3 seconds Every 3 seconds
Normal Mode LED 1 Green Solid (steady glow) (None)
Battery Replacement LED 4 Red Flashes every 1 second for 5 seconds only Every 1 second for 5 seconds only
Fault LED 4 Red Solid (steady glow) until UPS shuts down after 5 seconds Continuous until UPS shuts down
Figure 2 - Rear Panel
Figure 1 - Front Panel LEDs
LED 2
(amber)
LED 3
(amber)
Fault
symbol
Overload
symbol
Mains
symbol
On/O
button
LED 1
(green)
LED 4
(red)
Battery
symbol
UPS CONTROLS AND CONNECTIONS
Step 4 Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the On/O button (see Figure 1 below).
LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.
Step 5 Connect the Loads
The UPS has three battery backup sockets that
provide power when the UPS operates on battery
(see Figure 2 below).
• Plug the loads into the battery backup sockets
on the rear of the UPS.
Caution: Do not connect a laser printer to the UPS.
Step 6 Connect the Network Surge Protection
The UPS has two RJ-45 jacks for network lines
(see Figure 2 below).
• Connect a single-line network cable into the RJ-45
network surge protection IN jack on the rear of the UPS.
•Connect an RJ-45 cable from the OUT jack on the rear of
the UPS to a port on a PC or network device such as a router.
Step 7 Set Up Liebert shutdown software
To start using the Liebert shutdown software:
• Install the Liebert shutdown software. See the software
user manual for installation instructions.
•Connect one end of the USB cable (supplied) to the
USB port on the rear of the UPS. Connect the other end
to a USB port on the computer. See the software user
manual for operating instructions.
UPS
USB
cable
Liebert
shutdown
software
CD
Quick-start
guide
SETUP
Step 1 Inspect the Package
Inspect the package and the UPS upon receipt. Notify the carrier and dealer
of visible damage.
Step 2 Decide Where to Place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat.
Provide at least 100mm (4") of clearance on all sides of the unit
for proper ventilation.
Step 3 Charge the UPS Battery Before Use
The UPS battery is not charged before shipping. It MUST be charged before use.
•Connect a user-supplied power cord from the UPS to a wall socket and charge for at
least eight hours.
Note: If battery is placed in storage, charge the battery every six months if kept at
-15°C to +29°C (5°F to 85°F)—or every three months if kept at 30°C (86°F) or higher.
USB
Battery Power Supply
AC OUTPUT
Full Time Surge Protection
IN OUT
Surge sockets (2)
IEC 320 C13
RJ-45 jacks (2) - network
protection
USB
interface
Battery backup
sockets (6)
IEC 320 C13
Mains
breaker
AC mains
inlet
USB
BatteryPower Supply
ACOUTPUT
ACINPUT
FullTime Surge Protection
IN OUT
USB
BatteryPower Supply
ACOUTPUT
ACINPUT
ACINPUT
FUSE
FullTime Surge Protection
IN OUT
USB
BatteryPower Supply
ACOUTPUT
ACINPUT
FullTime Surge Protection
IN OUT
IMPORTANT SAFETY INSTRUCTIONS
• Do not connect equipment that may overload the UPS or demand half-wave
rectification, such as a laser printer.
• Connect the UPS only to an earthed / grounded socket that meets electrical safety
guidelines.
• Locate the UPS near a wall socket. Do not use an extension cord between the UPS and
the socket.
• Use CE-marked cables only for connections between mains, the UPS and equipment.
• The Liebert PSA has been designed for small oice/home oice use only; it is NOT
recommended for use in life-support applications.
•In the event of an emergency, press the OFF button and disconnect the power cord
from the AC mains to properly disable the UPS.
• Do not attach power strips or surge suppressors to the UPS.
• Do not attempt to service any parts inside the UPS except the batteries.
Failure to adhere to this could cause personal injury or equipment malfunction and
void the warranty.
• For technical support:
• Visit www.vertivco.com or
• Send an e-mail to [email protected] / [email protected] (in EMEA)

REPLACING THE BATTERY
To replace the battery:
1. Turn o all connected loads, then turn o the UPS (batteries are NOT hot-swappable).
2. Use a Phillips head screwdriver to remove the two top cover screws from the back of
the UPS.
3. Slide the top then pull outward to remove it.panel backward 13mm (1/2"). Slide the
front panel upward,
4. Gently pull the batteries out of the UPS.
5. Remove the black wire from the negative (-) terminal and the red wire from the
positive (+) terminal.
6. Verify that the replacement battery matches the dimensions and battery type in the
Specifications section below.
7. Connect the battery leads to the new batteries. Be sure to reconnect the red wire to
the positive (+) terminal and the black wire to the negative (-) terminal.
Note: Small sparks may occur at the battery connectors during reconnection.
8. Slide the batteries into the UPS.
9. Reposition the front panel and slide downward until it slides into place.
Slide the top panel forward until flush with the front panel. Reinsert the two top cover
screws removed in Step 2 .
Dispose of the old batteries properly at an appropriate recycling facility.
SolutionsPossible CausesProblem
Utility power is normal, but LED 1 is not illuminated.
The UPS may not be turned on.
The power cord may not be connected properly.
The upstream mains circuit breaker may be tripped.
• Press the On/O button to turn on the UPS.
• Connect the power cord securely into a wall outlet.
•Reset the circuit breaker.
LED 2 flashes (amber) every 3 seconds, but there is
no output power.
Alarm buzzer beeps continuously although mains is
normal. The UPS may be overloaded (check LED 2).
The UPS is on and connected to input power, but fails
to operate properly.Utility power may be outside the unit’s operating range.• If mains is normal, try reconnecting mains and restarting the UPS.
1500/9001000/600Capacity (VA/W)
11.6 (25.6)9.5 (20.9)Net Weight, lb. (kg)
12.8 (28.2)10.7 (23.6)Shipping Weight, kg (lb.)
147 × 360 × 234 (5.8 × 14.2 × 9.2)Dimensions - W × D × H, mm (in.)
160-287VACOn-Line Mains Voltage
50/60Hz ±5HzOn-Line Frequency
Typical 185-252VACOutput Voltage (Mains Normal)
230VAC ±5%Output Voltage (Battery Operation)
Stepped sinewaveOn-Battery Wave Form
12V x 9Ah x 212V x 7.2Ah x 2Battery Type - VDC × Ah × Quantity
6-8 hours to 90%Typical Recharge Time
60-100 minutesBattery Run Time*
Audible alarm / LEDAudible and Visual
IEC 320 C13 (6)Backup Sockets
IEC 320 C13 (2)Surge Sockets
0 to 40 (32 to 104)
Operating Temperature, °C (°F)
-15 to 40 (5 to 104)
Storage Temperature, °C (°F)
0%-90%, non-condensingOperating / Storage Relative Humidity
Class B
Agency
IEC62040-1-1Safety
ISTA Procedure 1A Certification
* Battery run time may vary depending on load
Steps 4 and 5
Steps 2 and 3
Transportation
The UPS battery reached end of life.UPS does not provide expected backup time. • Replace the internal battery.
• Disconnect some equipment from the UPS.
Battery voltage may be too low. • Recharge the UPS for 8 hours.
PSA1000MT3-230UModel Number PSA1500MT3-230U
EMI Classification
SPECIFICATIONS
BATTERY REPLACEMENT
• Servicing of batteries should be performed or supervised by personnel knowledgeable about batteries and required precautions.
•When replacing batteries, replace with the same type and number of batteries or battery packs.
CAUTION
Do not dispose of batteries in a fire. The batteries may explode.
CAUTION
Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It is toxic.
This product is also designed for IT power systems with phase-to-phase voltage 230V.
-
TROUBLESHOOTING
If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, please contact your local Vertiv representative.
800-222-5877 (Outside U.S. 614-841-6755)
[email protected] / [email protected] (in EMEA)
Website : www.vertiv.com
1050 Dearborn Drive
United States
P.O. Box 29186
Columbus, OH 43229
© 2019 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or
registered marks of Vertiv Group Corp. All other names and logos referred to are trade names,
trademarks or registered trademarks of their respective owners. While every precaution has been
taken to ensure accuracy and completeness herein, Vertiv Group Corp. assumes no responsibility, and
disclaims all liability, for damages resulting from use of this information or for any errors or omissions.
Specifications are subject to change without notice.
Technical Support / Service