Vestil OROAD-400 Specification sheet

OROAD-400 (3/6/07) 2/1/2013 update
OFF-ROAD TRACTION DRIVE ELECTRIC CART
USE &MAINTENANCE MANUAL
VESTIL MANUFACTURING CORP.
2999 NORTH WAYNE STREET
P.O. BOX 507, ANGOLA,IN 46703
TELEPHONE:[phone] -OR-TOLL FREE [phone]
FAX:[phone]
URL:WWW.VESTILMFG.COM EMAIL:[e-mail]
NOTE:Compliance with regulations, codes, and/or statutory (non-voluntary) standards enforced in the location
where the cylinder truck is used is exclusively the responsibility of the end-user.
Table of Contents Table of Figures
Safety Principles….………………………............ 2 FIG. 1 “Right side view”…….………… ……….……….................……….3
Safety Guidelines………………………………… 2 FIG. 2 “Rear view (operator end)”…………………………………………. 3
Product specifications……………………………. 3 FIG. 3 “Front view (loading end)”…………………………………………...3
Parts List…………………………………………… 6 FIG. 4 “Main features”………………………………………………………. 4
Operation instructions……………………………. 7 FIG. 5 “Operation controls”…………………………………………………. 4
Perimeter guard adjustment & battery access….7 FIG. 6 “Operation control panel”…………………………………………… 4
Battery charger use and operation……………… 8 FIG. 7 “Exploded parts diagram”……………………………………………5
Maintenance………………………………………. 9 FIG. 8A “Raising the deck & adjusting guards”…………………………... 7
Limited Warranty………………………………….. 10 FIG. 8B “Adjustment range of perimeter guards”………………………… 7
FIG. 8C “Threaded knob”…………………………………………………… 7
1

SAFETY PRINCIPLES
This manual provides specifications and describes recommended use and maintenance practices. Each set of
Off-road traction drive platform cart conforms to the generalized specifications disclosed in this manual and fulfills our
demanding standards for quality, safety and durability.
Each person who might participate in the use or maintenance of the product must read this manual and fully
understand the directions BEFORE using or performing maintenance on the cart. If you do not understand an
instruction, ask your supervisor or employer for assistance. Failure to adhere to the directions in this manual
might result in serious personal injury or even death.
Vestil is not liable for any injury or property damage that occurs as a consequence of failing to apply either: 1) the
instructions that appear in this manual; or 2) the information provided on labels affixed to the product. Furthermore,
failure to exercise good judgment and common sense might result in property damage, serious personal injury or
death. Such injury or damage is solely the fault of the person(s) who fail to exercise good judgment; it is not another
responsibility delegated to manufacturers.
This manual uses SIGNAL WORDS to classify personal injury risks and situations that might lead to property
damage, as well as to draw attention to safety messages. The reader must understand that each signal word
indicates the seriousness of the described hazard.
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS
INJURY. Use of this signal word is limited to the most extreme situations.
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS
INJURY.
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or
MODERATE injury.
Identifies practices likely to result in product/property damage, such as operation that might
damage the cart.
SAFETY GUIDELINES
Failure to read and understand the instructions included in this manual BEFORE using or maintaining the
platform cart constitutes misuse of the product.Study the entire manual before using or maintaining the product
for the first time, and subsequently as necessary to refresh your understanding. DO NOT attempt to resolve any
problem(s) with the device unless you are both authorized to do so and certain that it will be safe to use afterwards.
If this product is used improperly or carelessly, the operator and/or bystander(s) might sustain serious
personal injuries. To reduce the likelihood of injury:
When not in use, store the cart in an indoor, dry location. DO NOT expose the electrical system to moisture (rain,
snow, etc.).
DO NOT remove or obscure any label. Verify the placement and legibility all labels. DO NOT use the cart UNLESS
all labels are attached and readable.
DO NOT attempt to transport unbalanced loads with the cart. Only use the cart to transport stable loads. Secure the
load to the deck with straps, if necessary to prevent the load from shifting during transport.
DO NOT exceed the load rating. ALWAYS make sure that the load weighs no more than the rated load of the coil
hook. Rated load varies with the supporting surface (ground/floor): 1) Maximum rated load when used on smooth,
level improved surfaces = 600 pounds (273kg); 2) when used on level, unimproved surfaces (e.g. gravel, dirt) = 500
pounds (227¼kg); and 3) inclined/sloped surfaces UP TO a maximum of 13 degrees = 400 pounds (182kg).
DO NOT ride on the cart or allows other person(s) to do so.
Inspect the cart prior to each use. DO NOT use the cart if it is noticeably AND dangerously damaged. Examples of
noticeable damage include, but are not limited to punctured tire(s), non-functioning brake lever, cut or exposed
electrical wires.
While traveling up or down an incline, DO NOT change the speed setting. Always traverse the whole incline in the
same speed setting, because changing the speed setting might cause the cart might roll down the incline in an
uncontrolled manner.
ALWAYS start the cart with the speed selection knob in the “Stop” position (see p. 4). ALWAYS return the speed
selection knob to “Stop” when the cart is not in use.
Improperly recharging the batteries might either cause the batteries to explode or result in battery damage. To
properly recharge the batteries: 1) Shut off the power (turn the switch key to “off”); 2) connect the AC extension cord
of the charger to the outlet of a nearby power supply (the charger will automatically turn on and it will run at a rate that
matches the requirements of the batteries.) When the batteries are fully charged, the charger will only supply enough
current to maintain charge; 3) disconnect the AC plug from the power supply once charging is complete.
DO NOT leave a loaded cart unattended. Always unload the cart BEFORE leaving the cart unattended.
Page 2 of 10

FIG. 1: Right side view
Page 3 of 10
Improved
surfaces
Unimproved
surfaces
Inclined surfaces
(max. 13% grade)
Uniform static capacity in
pounds (kg) 600
(273kg)
500
(227kg)
400
(182kg)
Net weight in pounds (kg) 323
(~147kg)
Deck dimensions in inches
(cm)
31½ x 52½ x 15¾
(80 x 133.4 x 40)cm
Front wheels Rear wheels
Wheel dimensions in
inches (cm) 3½ x 11
(9 x 28)cm
6 x 14
(15¼ x 35.6)cm
Battery specifications
(each cart has 2 batteries)
12V; 40A·h
Power sufficient for 4hours use
Battery charger 24V (AC)
Motor specifications 600W; 24V (DC)
Brakes Electrical and mechanical
Drive mode Differential gears: High; Low; & Reverse
FIG. 3: Front view (loading end)
Measurement Dimension
1 7.2in.
18.3cm
2 33.5in.
85cm
3 37.5in.
95.25cm
4 5.2in.
13.3cm
5 31.5in.
80cm
6 7.3in.
18.5cm
7 15.75in.
40cm
8 3in.
7.5cm
9 36.8in.
93.5cm
10 25.6in.
65cm
11 24in.
61cm
Product specifications:
FIG. 2: Rear view (operator end)

Fig. 4: Main features O
p
eration control
p
anel
Basket
Front tires
O
p
erator handle
Self-propulsion
lever
Load/panel
deck
Deck
rails
Rear tires
Operation
control
panel
Fig. 5: Operator controls
Basket
Handle
Brake lever lock
Brake lever
Ke
y
switch
Green LED
(full charge)
S
p
eed selection knob
Recharging
socket
Fig. 6: Operation control panel
Yellow LED
(less than full
charge)
Red LED
(low charge)
Ke
y
switch
Headlight switch
Direction governing lever
Battery charge gauge
reverse
Page 4 of 10

Item Part Name Qty. Item Part Name Qty. Item Part Name Qty.
1 Gasket Φ8 33 46 Break pole 191 Steering Bracket 2
2 Bolt M8X25 2 47 breath device 192 Bolt M10X25 12
3 Screw M5X14 3 48 Shaft Key 5X14 193 Steering Bracket 2
4 Nut M5 4 49 II Gear 194 Sleeve 4
5 Screw M5X8 2 50 Differential shell 195 Core Shaft 2
6 Gasket Φ5 9 51 Pin Shaft 196 Steering Tire 4.1/3.5-
52
7 Gasket Φ5 29 52 Pin 5X30 197 Oil Cup M6 2
8 Motor Bracket 1 53 Bolt M8X55 298 Nut M8 1
9 Bolt M8X40 2 54 Bolt M8X55 699 Spring 18 2
10 24VDC Motor 1 55 Shaft Ring Φ25 4100 Bolt M8X30 1
11 Connect Sleeve 1 56 Bearing 6205 2101 Screw M6X16 1
12 Rubber seat 35X7 1 57 Short Shaft 1102 Bracket 1
13 Right Cover 1 58 Key 6X32 2103 Rod 1
14 Nut M8 8 59 Sealing - I 1104 Gasket 6
15 Shaft Sleeve
G10X8.5X15 2 60 Short Shaft Bracket 1105 Nut M6 7
16 Bearing 6201N 1 61 Screw M8X20 8106 Battery 12V/40AH 2
17 I Gear Shaft 1 62 Bearing 6005 2107 Battery Cable 1
18 Bearing 6201 1 63 Ring 2108 Battery Cover 1
19 Bearing 6202N 1 64 Sealing 25X47X8 2109 Brake Line 1
20 II Gear Shaft 1 65 Flange 1110 basket 1
21 Shaft Key 4X12 1 66 Gasket Φ14 2111 Brake handle 1
22 I Gear 1 67 Gasket Φ14 1112 Screw M5X30 2
23 Location Sleeve 1 68 Nut M14 2113 Nut M5 6
24 Bearing 6302 1 69 Drive Wheel 145/70-
62114 Bolt M6X30 1
25 SealingII 1 70 Bolt M8X20 6115 Screw M3X25 2
26 Nut M10 11 71 Gasket Φ810 116 Gasket Φ36
27 Gasket Φ10 15 72 Long Shaft 1117 Nut M3 3
28 Gasket Φ10 27 73 Long Shaft Bracket 1118 Switch 1
29 Left Cover 1 74 Bolt M10X30 4119 Switch Pipe
30 Hole M20X1.5 1 75 bottom plate 2120 Screw M3X8 4
31 Break Line Bracket 1 76 side frame 2121 Cover 1
32 Screw M6X16 6 77 front frame 1122 Screw M4X12 4
33 Gasket Φ6 13 78 locking bolt M10 1123 Gasket Φ44
34 Bolt M10X40 1 79 carriage
subassembl
y
1124 Gasket Φ44
35 Spring 1 80 locking bolt M6 6125 Battery Panel 1
36 Brake Disc 1 81 Pin Shaft B12X80 2126 Control Panel 1
37 Brake Gasket 82 Pin 4X24 2127 Switch 1
38 Brake Disc others 2 83 Gasket Φ12 2128 Anti-Back Bracket 1
39 U Wire 1 84 Screw M5X16 5129 Anti-Back Bracket 1
40 Gasket Φ6 12 85 Control Box 1130 Switch 1
41 Gasket Φ6 4 86 Control Parts 1131 Power Switch Locker 1
42 Bolt M6X14-4.8 4 87 24V LED Lamp 2132 Key Hole Anti-Water
Cover 1
43 Break Cover 1 88 24VDC buzzer 1
44 Break Seat 1 89 bodywork 1
45 Break Seat Gasket 1 90 Overload Protection
Device 1
DC CARRY TRUCK OROAD-400 PARTS LIST

Operation:
The speed control knob should already be in the “Stop” position, but if not, turn the knob to “Stop”.
Insert a key (two keys are enclosed inside packaging with this manual) into the slot in the key switch, and turn the key
to the “On” position. The battery charge/capacity display (see FIG. 6) will illuminate when system power is turned on
(see Fig. 6 on p. 3). The red LED will flash if the batteries require recharging.
Select the desired speed setting: low or high with the speed selection knob. To propel the cart, grasp the handle and
press the self-propulsion lever and handle together. Slowly and gradually release the lever to stop the cart.
Turn the speed selection knob to “Stop” before the cart is left unattended.
The “Direction governing lever” prevents accidental operation in reverse. To use the lever, pivot it over the operation
control panel as shown in FIG. 6. Always use the lever when operating the cart in forward (low or high). To operate
the cart in reverse, flip up the lever, turn the speed selection knob to “Reverse”, and then press the self-propulsion
lever and handle together.
Perimeter Guard Adjustment & Battery Access
FIG. 8B: Adjustment range of
perimeter guards
Maintenance
prop
Arrows show the positions of threaded knobs used to secure the
perimeter guards to the deck. To adjust the position of a perimeter
guard, loosen the appropriate knobs (indicated by arrows in the
drawing below and shown in “Threaded knob” below); then pull the
guard away from, or push it towards, the deck (See “Adjustment
range of perimeter guards”). After adjusting the guard, tighten the
knobs to secure it in the adjusted position.
FIG. 8A: Raising the deck & adjusting guards
Threaded hole in
chassis
Deck tab FIG. 8C: Threaded knob
Maintenance prop
retaining clip
Flan
g
e of deck frame
Operator
end
Front end
Access the batteries by lifting the deck and
securing it in the elevated position with the
maintenance prop. The deck is secured to
the chassis with a threaded knob that
extends through the deck tab and into a
threaded hole in the chassis. To raise the
deck, first remove this knob.
To properly engage the deck with the
maintenance prop, the flange of the deck
frame should fit inside the bracket at the end
of the maintenance prop.
Batteries
Page 7 of 10

Battery charger use and operation:
Working with or near lead acid batteries is dangerous. Batteries contain sulfuric acid and produce explosive gases. A
battery explosion could result in loss of eyesight and/or serious burns.
Do not smoke, or allow a spark or flame, near batteries. Only charge the batteries in a clean, dry, and well-ventilated
location. Do not lay tools or metallic items on top of any battery. All repairs to a battery must be made by experienced
and qualified personnel.
Before working with batteries, remove personal items such as rings, bracelets, necklaces, and watches. Batteries
produce sufficient energy to weld jewelry to metal, and to cause severe burns.
Always have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
Operating the cart with a low battery voltage can cause premature motor contact failure.
Do not expose the cart or charger to moisture (rain, snow, sleet, etc.).
Replace defective cords or wires immediately.
Check the water level of the batteries frequently.
The battery charger consists of 2 parts: 1) the charger; and 2) a power cord that plugs into the charger.
To charge the batteries, plug the female end of the power cord into the charger; connect the charger plug to the charger
socket of the operation control panel; plug the male end of the power cord into a (standard) 115V wall receptacle; and
then press the power switch on the charger.
Do not connect the charger to an extension cord unless it is unavoidable. If an extension cord is
necessary, it should be as short as possible with a large cross-section. A cord of small cross-section and/or longer length
will decrease the output of the charger, and consequently will increase the time necessary to charge the batteries. This
can also cause the 115V cord to overheat.
When properly connected, a series of 3 LED’s indicates the status of current flowing to the battery, as follows: Power LED
is always green when charger is plugged in.
The status light is as follows:
Red only – the charger is providing full output to the battery.
Yellow – the charger is “topping off” the battery.
Green – the charger is providing a “float,” or maintenance, charge.
Unplug the charger before using the cart.
Charger
O
p
eration control
p
anel
Charger socket
on operation
control panel
Charger plug
Power cord
Page 8 of 10

Maintenance:
• Only trained and authorized personnel should be permitted to maintain, repair, and inspect the unit.
• Keep usage area dry, clean, and well ventilated.
• To avoid fire hazards, have fire protection equipment present at all times during any maintenance or repair. Do not use
open pans or containers of flammable fluids.
• Safety devices shall be inspected at monthly intervals and maintained to a safe operating condition. A maintenance log
must be kept.
• Electrical components shall be maintained and inspected for safe operation.
• The battery electrolyte level should be checked before charging the battery. The level should be maintained at 1/2 inch
above the plates. If the level is low, add approved water before charging. Do not overfill. It is not necessary to charge the
battery every day if there is more than 1/3 left, however the battery should be charged at least once a week.
• Disconnect batteries before working with the electrical system.
• When checking the hydraulic fluid level, make certain that the unit is fully lowered and on a level floor. Remove the filler
cap and check the level of the fluid. Use a top quality hydraulic fluid. Do not use hydraulic brake fluid.
• Before leaving the unit, stop the unit, lower the forks fully, turn off the power, and remove the key.
• Before working on the unit, lower the forks fully, check that the brake is working properly, turn off the power, and restrain
the unit using chocks or other restraining devices.
Page 9 of 10

LIMITED WARRANTY
Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship during
the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered
by the warranty, after we receive a proper request from the warrantee (you) for warranty service.
Who may request service?
Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an
authorized distributor AND Vestil has been fully paid.
What is an “original part”?
An original part is a part used to make the product as shipped to the warrantee.
What is a “proper request”?
A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the
shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests by
any of the following methods:
Mail Fax Email
Vestil Manufacturing Corporation [phone] [email protected]
2999 North Wayne Street, PO Box 507 Phone
Angola, IN 46703 [phone]
In the written request, list the parts believed to be defective and include the address where replacements should be
delivered.
What is covered under the warranty?
After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether
your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the entire
product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following original
dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers defects in
original parts that wear under normal usage conditions (“wearing parts”), such as bearings, hoses, wheels, seals, brushes,
and batteries.
How long is the warranty period?
The warranty period for original components is 90 days. The warranty period begins on the date when Vestil ships the
product to the warrantee. If the product was purchased from an authorized distributor, the period begins when the
distributor ships the product. Vestil may extend the warranty period for products shipped from authorized distributors by
up to 30 days to account for shipping time.
If a defective part is covered by the warranty, what will Vestil do to correct the problem?
Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you
to discuss your claim.
What is not covered by the warranty?
1. Labor;
2. Freight;
3. Occurrence of any of the following, which automatically voids the warranty:
Product misuse;
Negligent operation or repair;
Corrosion or use in corrosive conditions;
Inadequate or improper maintenance;
Damage sustained during shipping;
Accidents involving the product;
Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written
authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or
abnormal wear.
Do any other warranties apply to the product?
Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed
by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.
Page 10 of 10