Viavi SmartOTDR Parts list manual

SmartOTDR
GETTING STARTED MANUAL
 
Laser safety
The provisions contained in two standards define the safety procedures to be
observed both by users and by manufacturers when utilizing laser products:
-EN 60825-1: 2001 - Safety of laser products – Part 1: Classification of prod-
ucts, requirements and user guidelines.
-FDA 21 CFR § 1040.10 - Performance standards for light-emitting products
- Laser products.
Due to the range of possible wavelengths, power values and injection charac-
teristics of a laser beam, the risks inherent in its usage vary. The laser classes
form groups representing different safety thresholds.
-VFL option: Laser Class 2.
Due to the reduced dimensions of the optical modules, it is not possible to
attach the required warning labels to them. In line with the provisions of Article
5.1 of the EN 60825-1 standard, the laser class identification labels are shown
below:
Ref. stan-
dard
EN 60825-1, Edition 1.2,
2001-08 FDA21CFR§1040.10
Class 2
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
CAUTION
LASER RAD IATION - DO NOT STARE
INTO BEAM
CLASS II LASER PRODUCT
The user must take the necessary precautions concerning the optical
outputs of the instrument and follow the manufacturer’s instructions.
AC/DC power supply safety
!
Always use the proper adaptable plug to connect the power supply
to an electrical outlet. Viavi is not responsible for direct or indirect
damage including damage to persons or property if the power
supply is not use correctly. For assistance using one of the Viavi
supplied adapters (your specific regional adapter may not be avail-
able) please refer to the user manual.

   
Before connecting a fiber into a test module, inspect and clean the module
bulkhead and the fiber jumper connectors.
1
Use a video inspection scope (such as P5000i) to verify the connector
quality. Follow this simple “INSPECT BEFORE YOU CONNECT” process
2
Use appropriate cleaning material (e.g. IBC™ cleaner, cotton swab, dust
air sprays, etc...) and re-inspect to confirm.
3
Carefully align the connector and test port prior to mating both
Never force the connector ferrule or insert it with an angle into the test port adapter.
Mechanical stress may permanently damage the ceramic sleeve of the adapter or
the end face of the connector.

     mart
1
Connect the Microscope to the
SmartOTDR USB port.
2
On the Home page, select the Mi-
croscope icon
3
Use Focus control button on Microscope to adjust focus
4
Press
SETUP
and configure the test of the connector.
Configure the file storage
Display informa-
tion on scope
& current test
result displayed
5
Press
RESULTS
to return to Results page, and press to launch the test
of the connector.
A summary of test results is displayed.
Zones: A - Core / B - Cladding / C - Epoxy / D - Ferrule.

mart 
6
1
7
131211
1098
5432
14
15
16 17
20
18
1
5’’ HVT Capacitive Screen
11
Direction & validation keys
2
Charge indicator
12
Results page
3
On indicator
13
Buzzer
4
File menu
14
AC/DC Input
5
Setup menu
15
Slave Mini USB port
6
Start/Stop
16
VFL connector
7
Testing indicator
17
USB ports (2)
8
On/Off
18
OTDR port / continuous light source / power meter
9
Home page
19
OTDR live port (in-service test)
10
Cancel (switch off functions)
20
WIFI or Bluetooth options

      
 
1
On the Home page, select Smart TEST icon .
2
From the Results page, press
SETUP
.
Allows to load an existing con-
figuration file (Smart Config.)
3
Press
START/STOP
to launch the test of the connector.
Step1: connector check
Step2: acquisition in progress
3
At the end of test, the results trace displays.
ATrace: select the active trace (multi-traces analysis)
Summary: display a summary of results for each wavelengths
SmartLink (optional): Icon based map view
BZoom and shift on trace
CAllows to modify some acquisition
parameters and load Smart Config.
D Save in a sor file and create a txt or
pdf report of the results
EToggle between
Table of results <-> Fault Locator
A
B
C
D
E
Launch a real time acquisition pressing the Start/Stop button for more
than 2 seconds.

   /   mart config. 
 
1
On the Home page, select ExpertOTDR icon .
2
From the Results page, press
SETUP
.
3
Configure the OTDR parameters.
4
Select one parameter and press to save the current configuration.
5
Press to validate.
6
Press
FILE
to access the configuration file.
Summary of configuration parameters into the file
To perform acquisitions in Expert OTDR, see chapter “Launching a
reflectometry test and displaying results” in Module User Manual.

      
1
Once results are displayed, press
FILE
to display the file Explorer.
2
Select the location where the directory must be created.
Storage media selected
3
Press Create Directory.
4
Enter a name for the new directory.
5
Press to validate.
The traces acquired can be saved in
the new directory.
Sub-directory
created
The files can be transferred, using Edit sub-menu:
-to USB folder if plugged
-to your remote device via Bluetooth
-to your preferred cloud storage server
To get more information on Connectivity and files transfer, refer to
SmartOTDR Base Unit User Manual.

   
1
In the Results screen, press Fast Report key.
2
Select the Save Mode and , if necessay, modify the Fiber / Cable / Link
parameters:
File Only: save exclusively the
OTDR trace(s)
File + txt: save the OTDR
trace(s) & generate a txt file
File + pdf: save the OTDR
trace(s) & generate a pdf file
All: save the OTDR traces & gen-
erate a pdf and a txt file
3
Press Save All.
4
In the edition keypad, enter the filename or
press Auto Filenaming menu key.
5
Press
FILE
to display the file Explorer.
Once saving is completed, the file(s) is/are displayed in the Explorer.

 
1
On the Home page, select > .
2
In Setup page, press Wireless key and configure the WIFI connection in
Configuration box.
3
Press Scan SSID.
4
Press Select once the desired network to connect to is selected, via
WIFI.
In setup page, the SSID parameter is automatically con-
figured with the one selected.
5
Configure the Login, Password, and Autoconnect
parameters.
6
Press to connect the configured SSID.
On the upper banner, the icon WIFI “inactive” turns active .
7
To work on WIFI with the Platform, configure the 802.11
parameters, and the proxy parameter if necessary.
8
Note the IP address of the SmartOTDR to be able to
remote screen on PC or to transfer files via WIFI.
To get information on WIFI use, refer to SmartOTDR Base Unit User
Manual.

SmartOTDR - Getting Started Manual - PN7SMART202 Rev003 - November 2016 - Copyright © 2016 10
 
If you require technical assistance, call 1-844-GO-VIAVI. For the latest TAC
information, go to http://www.viavisolutions.com/en/services-and-support/
support/technical-assistance.