Vicon DS-K182HP User manual

Hikvision USA Inc.
18639 Railroad Street
City of Industry, CA 91748
Toll-Free: [phone] (U.S. and Canada)
Phone: [phone]
www.hikvision.com
QUICK START GUIDE
125-kHz PROXIMITY CARD READERS
This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.
Installation and wiring of systems must be in accordance with the National Electrical Code, ANSI/NFPA 70.
1.0 Introduction
A key component of a physical security electronic access control system, a proximity card reader is based on RFID technology. In operation it is
capable of reading data stored on a proximity credential via radio frequency and without physical contact, and then passing the data obtained to
the physical access control system. Access control systems typically manage and record the movement of individuals through a protected area,
such as a locked door.
2.0 Mounting Provisions
Each reader may be installed either indoors or outdoors.
DS-K182HP
DS-K170HPK
Mullion Mount
•
Mullion Mount with Keypad*
•
*Plastic or metal.
3.0 Reader Wiring
NOTES:
aSingle Line LED: This is the standard operating mode and does not
make use of the Orange conductor. The LED is Red when the reader is
idle and flashes when a card is presented. The LED turns Green when
the Brown Conductor is pulled low by the access control panel.
bDual Line LED: This mode makes use of both the Brown and Orange
conductors. The Brown conductor controls the Red LED and the Orange
conductor controls the Green LED. LED states are determined by the
access control system option and capability.
4.0 Cable Requirements
24 AWG minimum, multi-conductor stranded with an overall foil shield, for example Belden 9535 or similar, supporting the five conductors
comprising the physical layer of the Wiegand interface (power, ground, data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or
similar, for all reader functions. Contact your access control system manufacturer for their specific requirements. Per the SIA’s Wiegand
specification, maximum cable length is 500 feet (152 m).
5.0 Output Formats
Wiegand (industry standard 26-bit Wiegand and custom Wiegand formats).
6.0 Grounding
Shield (drain) continuity must run from the reader to the access panel. Shield (drain) and reader ground must be tied together at the access panel
and connect to an earth ground at one point.
7.0 Power
Reader may be powered by the access panel. A linear power supply is recommended for best operation.
Wiegand
Conductor
Function
Red
DC (5-16 VDC)
Black
Ground
Green
Data 0
White
Data 1
Brown
Red LEDa
Orange
Green LEDb
Yellow
Card Present
Blue
Beeper
Violet
fleaPower
Drain
Shield Ground

Hikvision USA Inc.
18639 Railroad Street
City of Industry, CA 91748
Toll-Free: [phone] (U.S. and Canada)
Phone: [phone]
www.hikvision.com
8.0 Voltage
5 to 16 VDC. 12 VDC at the reader is recommended for best operation.
Model
DS-K182HP
DS-K170HPK
Current Draw
30 - 75 mA
70 - 110 mA
9.0 fleaPower™ Control Line
To reduce the average current required by the reader, pull the purple conductor low.
10.0 Connection
Connection must be done in accordance with NFPA 70. Do not connect to a receptacle controlled by a switch.
11.0 Troubleshooting
1. When the reader is first powered on it will beep 4-times, and the LED will shinered.
2. Presenting a supported access credential will result in the reader beeping and the LED flashing once.
NOTE: The access panel controls LED functionality, such as switching the LED to green.
If the reader does not recognize the card or tag (no beep, no LED flash) or exhibits short read range, please see the table below for possible
causes and solutions.
Possible Cause
Corrective Action
Incorrect cabling
Verify gauge, connections and cabling length
Not enough power
12 VDC recommended, 5 VDC at reader is minimum
Incorrect card used
Verify if card technology is supported
Reader/access panel not properly grounded
Earth ground needed—verify shield and reader ground are tied at access panel and connect
to ground at one point
Supply generating interference
Linear power supply recommended, verify switching power supply before use
Should any of the corrective actions mentioned above not improve performance, disconnect the reader from the access panel and power it with a
separate power supply or 9 VDC battery, and re-test card functionality. By powering the readers separately, most variables that may lead to
reduced performance can be eliminated. Should the problem persist, please contact Hikvision directly.
Many HIKVISION Readers carry the following certifications:
FCC compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Product can be used without license conditions or restrictions in all European Union countries, including Austria, Belgium, Denmark, Finland,
France, Germany, Greece, Ireland, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and the United Kingdom, as well as other non-EU
countries, including Iceland, Norway, and Switzerland.
HIKVISION reserves the right to change specifications without notice.