Videofied XT 210 Manual

XT 210/640/730 GPRS Control Panel
INSTALL MANUAL
www.videofied.com
Doc. - Ref. 230-XT
Last modification date : June 2019
Firmware version : XLP.04.04.05.XXX and later

Description
The XT is a fully wireless alarm system. It can be powered by standalone batteries or connected to a power
supply. This panel is intended mainly for residential and commercial markets.
With the Motion Viewers™ and Videofied®range of products, the XT panel provides video verification in
case of intrusion.
The XT panel has three wired programmable inputs and two wired programmable outputs. Thanks to the
Mapping feature, the programmable inputs can be configured to trigger a video.
For specific applications, the XT alarm system offers the possibility to increase its Radio and/or GPRS
performances through the connection of externally wired antennas.
Technology
The XT alarm panel, like all Videofied devices, uses the S2View® patented technology. Which is an interactive
wireless and AES encrypted technology ensuring signal integrity and optimal security.
The reliability of the signal is guaranteed thanks to the two-way radio frequency transmissions with all the
peripherals of the Videofied®product line.
The integrated antennas allow the system to be totally wireless, thus preventing from the system beeing
inelegant and cumbersome, and eliminating the installation problems.
The jamming detection feature identifies any intentional jamming from a third party. On the other hand, the
supervision feature consists of transmitting signals between every device of the system and the alarm panel
XT. Through the supervision, the detectors transmit every 8 minutes a presence signal.
The entire RSI VIDEO TECHNOLOGIES team wishes you a successful installation.
www.videofied.com
INSTALL MANUAL
2
Introduction

www.videofied.com
INSTALL MANUAL
3
Introduction............................................................................................................2
Summary...................................................................................................3
1. XT Panel setup...................................................................................................4
1.1 SIM card installation...............................................................................................4
1.2 Panel mounting.........................................................................................................4
1.4 Powering and initialization........................................................................................5
1.5 Pairing the keypad....................................................................................................6
2. XTENDER Mode.........................................................................................................7
3. XT Panel programming...............................................................................................8
XTENDER mode configuration.........................................................................................13
4. XT features guide.....................................................................................................15
4.1 Get to access level 4...............................................................................................................15
4.2 How to Arm/Disarm the system.................................................................................................15
4.3 Arming and Siren Mode Configuration...............................................................................16
4.4 Manage badges and access codes..........................................................................................17
4.5 Delete the keypad or any other device.....................................................................................19
4.6 Read the event log...................................................................................................................20
4.7 Programmable inputs and outputs...........................................................................................20
4.8 Golden rules...............................................................................................................................21
5. Transmitted events list.............................................................................................22
6. 2G3G error codes....................................................................................................23
7. Technical specification and security notes...........................................................24
Summary

www.videofied.com
INSTALL MANUAL
4
1. XT Panel setup
Before removing the front cover from its box, Put the SIM card on the
plastic base (Take care to respect the right direction).
DO NOT insert or remove the SIM card while the panel is powered.
1.1 SIM Card Installation
Bracket holes
Fix the back casing on the wall using
the three mounting holes as shown.
Mounting the panel is not required for
programming.
1.2 Panel mounting

1.3 Powering and initialization
www.videofied.com
INSTALL MANUAL
5
1. XT Panel setup
• The panel is powered either with a mains power supply with 4 backup LR20 Alkaline batteries (Option 1 recommended) or with 4
LSH20 Lithium batteries (Option 2).
• Press and hold the PROGRAMMING BUTTON for 10 seconds, until the indicator LED blinks twice.
• The panel is now reset, a CMA, XMA or XMB has to be enrolled to configure the panel.
Programming button Mains power supply
Option 1
Option 2
THE CONTROL PANEL MUST BE CONNECTED TO AN EXTERNAL POWER SUPPLY (OPTION 1) WHEN
USING THE RINGTONE FEATURE OR SMARTPHONE APP.

• Press the XT programming button and release for the enrollment of a programming
keypad.
• Insert all LS14500 Lithium batteries into the keypad.
• Do not mount the keypad. It will display one of the following screens:
1.4 Pairing the remote keypad
RSI (c) 2013
videoed.com <=========XX=========>
or
• Press on both CLR and ESC NO keys at the same time and release. The indicator
LED on the keypad will blink rapidly. Wait for the keypad to pair.
• If the keypad doesn’t pair up with the panel and shows «XX», it certainly means
that it is still paired to another system and needs to be reset. Take the batteries out,
and press repeatedly on the keypad tamper switch. Then proceed to the above
steps.
www.videofied.com
INSTALL MANUAL
6
1. XT Panel setup

Arming O/P 1
Arming O/P 2
Existing Host
Panel
2.1 Standalone Mode
2.2 XTENDER Mode (From the host)
In this functioning mode, the XT
panel works as a standard hybrid
alarm system with 25 wireless
peripherals and 3 programmable
inputs.
It is a totally standalone alarm
system.
The XT panel can be used as standard standalone alarm system but it can also be connected to an existing alarm system capable of
latching a 9-12Vcc* voltage used for its arming/disarming.
When the XT panel is used in XTENDER mode, the system will only be able to arm and disarm by latching 9-12Vcc to its arming inputs
Arming Input 1 and/or Arming Input 2.
When the voltage switches to 0V, the panel will disarm automatically.
On a programed panel, you can choose between standalone and XTENDER modes from the menu :
CONFIGURATION (LVL 4) > GENERAL PARAMETERS > XTENDER *When using an XT in XTENDER
mode, the panel has to be powered
by the mains power supply.
www.videofied.com
INSTALL MANUAL
7
2. XTENDER Mode

Keypad Display Actions and comments
KEYPAD 1
RECORDED
RADIO RANGE TEST?
RF TEST
x/9
RF TEST
9/9
RADIO RANGE TEST?
INSTALLER CODE
4 TO 6 DIGITS
THEN OK/YES
INSTALLER CODE :
< - LANGUAGE : - >
ENGLISH (UK)
The system can also be programmed in: french, italian,
german, dutch, spanish, swedish, portuguese, danish,
czech and polish.
The language can be changed at any time once the panel
is programmed in the MAINTENANCE menu.
The Radio Range test must be run during the device
learning process in order to ensure proper pairing with
the control panel. This test measures the strength of
communication between the device and the control
panel. The keypad will display a real time radio range
value on a scale of 9.
To receive the most accurate results you must run the
radio range test for at least 30 seconds.
Result must be 8 out of 9 or better for reliable
transmission.
Using the Alphanumeric Keypad, enter the Installer Code
of your choice.
The Installer Code will be used for all future maintenance
and configuration.
This code is important to keep track of.
There is no back door or Default codes to the
system.
Please refer to the restriction rule for codes (Chapter 4.4).
Some codes are already used by default and therefore
cannot be used.
OK or YES
OK or YES
Please wait
OK or YES
ESC
NO
for language selection
OK or YES
CONFIRM CODE
OK or YES
OK or YES
www.videofied.com
INSTALL MANUAL
8
3. XT Panel Programming

Keypad display Actions and comments
CODE NAME :
OK or YES
ACCESS 1
REGISTERED
You may name the installer code using the Alphanumeric
Keypad.
If using automatic setting (called installer default list),
enter the name of the list.
Warning : If the wrong installers list name is used it
cannot be set later, the system must be defaulted.
Leaving the name blank by pressing
ESC NO , it will be
named ‘ACCESS 1’ by default.
Please wait
ADJUSTING DATE
AND TIME
DATE (YEAR):
12/ /
To set the year
OK or YES
DATE (MONTH):
13/01/
To set the month
OK or YES
You may proceed in the same way for:
Day, Hour and Minutes.
13/10/14 10:47
ENTRY COMPLETE !
ACCOUNT NUMBER :
CONNECTED TO
MONITOR. STATION?
OK or YES
Use the Alphanumeric Keypad to enter in a 4-8 digit
account number provided by the Central Station.
ACCOUNT NUMBER :
567001
OK or YES
ESC
NO
www.videofied.com
INSTALL MANUAL
9
3. XT Panel Programming

www.videofied.com
INSTALL MANUAL
10
3. XT Panel Programming
TEST (hour) :
04:
CODE/STATE
MODIFICATION?
Test Periodicity: 1 hour, 12 hours, 24 hours, 48 hours, 7
days or no tests.
We suggest a 24 hours periodic test call.
PERIODIC TEST
PERIODIC TEST :
24 HOURS
To select periodicity
OK or YES
OK or YES
TEST (minutes) :
04:15
OK or YES
OK or YES
CODE/STATE
MODIFICATION
Keypad display Actions and comments
CODE/STATE
MODIFICATION
The CODE/STATE MODIF. menu is to configure the
transmitted events to the monitoring station, use the
arrow keys to toggle between events and
OK or YES to
modify.
ALARM: event transmitted upon occurrence.
ALARM/END: event is transmitted on occurrence and
on event restoral.
NOT TRANSMITTED: event is not transmitted, however
it will appear on the keypad.
Please liaise with your Monitoring Station to ensure
that the requested events to transmit are correctly
set.
Events list
ESC
NO
SERVER
ADDRESSES ?
OK or YES
Wait
ESC
NO