Videofied VIA-Pro User manual

Owners
Manual
Manufactured by RSIalarm Document No. 2012 June 2007
VIA-Pro Security System

System Limitations ...........................................................................................................1
Your Privacy .......................................................................................................................1
About Your Security System .........................................................................................2
System Components .......................................................................................................2
Terms You Should Know .................................................................................................3
What Happens During an Alarm ....................................................................................3
Intrusion/Burglary Alarm ...............................................................................................3
Fire Alarm ..........................................................................................................................3
What to do If an Alarm Occurs ......................................................................................4
Stopping an Alarm ...........................................................................................................4
Alarms Caused By an Intruder ......................................................................................4
Fire Alarms ........................................................................................................................4
Accidental Alarms ............................................................................................................5
Preventing Accidental Alarms ......................................................................................5
Basic Systeevm Operation .............................................................................................6
Keypad Button Functions ...............................................................................................6
Keyfob Button Functions ................................................................................................6
Arming Modes ...................................................................................................................6
Arming the System .......................................................................................................... 7
Full Arming Mode .............................................................................................................7
Perimeter Arming Mode ................................................................................................. 7
Arming with Protected Doors or Windows Opened ..................................................8
Disarming the System .....................................................................................................8
Disarming when Arriving Home ....................................................................................8
Disarming after Overnight Arming...............................................................................9
Using Your System for an Emergency .........................................................................9
Activating an Alarm in an Emergency .........................................................................9
Special Arming Modes .................................................................................................. 10
Arming the System Using Special Arming Modes .................................................. 10
Voice and Email Alarm Messages ............................................................................... 10
Receiving Voice Alarm Messages by Phone ............................................................. 10
Receiving Alarm Messages by Email ......................................................................... 10
Advanced System Operation .........................................................................................11
Access Levels and System Menus ................................................................................11
Access Levels and System Function Control .............................................................11
Maintenance ......................................................................................................................11
Event Log ...........................................................................................................................11
Badges, Access Codes ....................................................................................................11
Alarm Parameters ............................................................................................................11
Changing the System Level ......................................................................................... 12
Programming and Deleting Access Codes ................................................................ 12
Access Code Changes Log ............................................................................................13
Changing Access Code Alarm Arming Mode Restrictions .................................... 14
Deleting Access codes .................................................................................................. 14
Creating Schedules ........................................................................................................ 15
Schedule Logs ............................................................................................................ 16-17
Viewing the History/Eventy Log ................................................................................. 18
Regulatory Information ................................................................................................ 19
Table of Contents

Thank you for choosing the Videoed security system.
System Limitations
Having an alarm system does not
guarantee protection against burglary,
re, or other security/safety related
conditions. All alarm systems are
subject to possible compromise or
failure to warn for several reasons,
including:
• If intruders have the technical means
of bypassing or disabling
• If power to detectors is inadequate
or removed.
• If smoke does not reach a smoke
detector.
For example, smoke detectors cannot
detect smoke inside chimneys, walls,
roofs, or if closed doors block the path
of smoke. Smoke detectors may not
detect smoke on building levels different
from their installed location. Smoke
detectors may not warn in time when
res are caused by smoking in bed,
explosions, improper storage of
ammables, overloaded electrical
circuits, or other hazardous conditions.
• If telephone service is interrupted
or disconnected. Telephone lines are
also vulnerable to compromise by
several means.
Having an alarm system may make
you eligible for reduced insurance
premiums. However, security systems
are no substitute for insurance. Security
systems cannot compensate you for
loss of life or property.
Your Privacy
RSIalarm security systems use
cameras for video verication of
alarms. It is important that you know
any cameras in your system are inactive
when the system is disarmed (off). A
camera is active only during an alarm
condition caused by activity inside the
premises when the system is armed (on).
This owner’s manual provides the necessary
information for using your system.
If you ever have any questions or concerns about
your security system, contact your installation/service
dealer. Use the space below to ll in your dealer contact
information for quick and easy reference.
Dealer name:
Phone number:
Vid e of ied Sec uri ty System Own ers Man ual 1

About Your Security System
This provides an overview of your
security system that describes the
components, terminology, and basic
information about alarm conditions
to help you become familiar with
your system.
We recommend that you read this
section before attempting to use your
system. Even if you have previous
experience with security systems, this
information is valuable since all
systems vary in their operation.
System Components
This is a wireless security system.
There are no wiring connections
between any components and the
control panel. The only required wiring
is for telephone line connections to the
control panel. The following describes
the individual components that may
be a part of your system:
Motion-activated Cameras—detect
persons moving within their eld of
view, activating a built-in camera that
captures a 10-second digital video clip
for verication. Some models have a
pet-immunity feature that allows roaming
pets weighing up to 40 lbs./18 kg.
Control Panel—monitors all compo-
nents in the system, activates sirens,
and noties you and the central
monitoring station of alarms.
Keypads—wall-mounted
devices that allow complete
operation of your system
and provide system status
information on a built-in
display.
Keyfobs—portable devices
that allow limited or basic
operation of your system.
Sirens—alert you
inside and outside to
emergency situations.
Outdoor sirens also
include a strobe light to help responding
authorities nd your location.
Door Contacts—
detect when protected
doors and/or windows
are opened or closed.
Environmental
Detectors—typically
smoke detectors that
activate when smoke is
detected
2
Motion
Sensor
0 lux
digital
camera

Terms You Should Knowsection
The following describes terms to
help you understand and operate
your security system.
• Access Codes—4- to 6-digit numbers
that allow only authorized persons to
operate the system.
• Arm—to turn on intrusion/burglary
protection so that the control panel
responds by sounding an alarm, if
necessary.
• Disarm—to turn off intrusion/burglary
protection.
• Arming Modes—determine how
much intrusion/burglary protection
is turned on.
• Entry/Exit Delays—allow authorized
persons time to enter (entry delay) or
leave (exit delay) the armed premises
through a designated delay door,
without causing an alarm.
• Instant—detectors in the system
programmed with no entry/exit delay
that trigger an immediate alarm when
activated while the system is armed.
• Panic Alarm—an alarm that you
activate from a Keypad or Keyfob
in case of an emergency.
What Happens During An Alarm
The following describes how your
system responds to intrusion/burglary
and re alarms.
Intrusion/Burglary Alarm
• The control panel activates interior
and exterior sirens.
• Keypads display the detector(s)
in alarm.
• The control panel reports the alarm
to the central monitoring station,
identifying the detector(s) that
triggered the alarm. If programmed
by your installer, you also receive
voice notication by phone (at your
ofce, cabin, on your cellular, etc.)
and/or by an Email message.
• If the alarm was caused by a motion-
activated camera, the control panel
includes a 10-second digital video clip
in its report for alarm verication. If
programmed by your installer, you
also receive the video clip on your
cellularphone.
• The central monitoring station
operator contacts the proper
authorities so they can be dispatched
to the premises.
Fire Alarm
• The control panel activates interior
and exterior sirens.
• Keypads display the detector(s)
in alarm.
• The control panel reports the alarm
to the central monitoring station,
identifying the detector(s) that
triggered the alarm. If programmed
by your installer, you also receive
voice notication by phone (at your
ofce, cabin, on your cellular, etc.)
and/or by an Email message.
• The central monitoring station
operator contacts the proper authori
ties so they can be dispatched to the
premises.
Vid e of ied Sec uri ty System Own ers Man ual 3

What Happens During An Alarm
What to do If an Alarm Occurs
The rst thing most people want to
know about their security system is how
to turn off the sirens or stop an alarm.
Alarms can occur automatically,
intentionally, or accidently whether the
system is armed or disarmed.
Intrusion/burglary alarms and re
alarms require different action, depend-
ing on the circumstances. This section
provides information to help prepare
you to take the correct action if an
alarm occurs.
Stopping an Alarm
Regardless of who or what caused
the alarm, this procedure silences
system sirens.
1. At the nearest Keypad, enter
Access Code +
YES
OR:
On any Keyfob, press the OFF button.
1. Interior sirens sound a long beep,
indicating the system is disarmed.
The display shows INTRUSION
DETECTED.
2. Press YES. The display shows
the device that was tripped, causing
the alarm.
3. Press YES. The display shows the
date, time, and level.
Alarms Caused By an Intruder
The sound of sirens may or may not
scare off intruders. Also, the sirens in
your system are programmed to stop
after a specic time setting expires.
Use the following guidelines to
determine what to do.
• If you arrive home and hear sirens
or see signs of forced entry (broken
windows, damaged doors, etc.), do not
enter the premises. An intruder may
be inside. Call for help from a cell
phone or other location and wait for
authorities to arrive.
• If you enter the premises and
discover there was an alarm, leave
immediately. Call for help from a cell
phone or other location and wait for
authorities to arrive.
Fire Alarms
Fire alarms require being prepared
ahead of time by planning your escape
routes from each room in your home
and practicing evacuating the building.
• Plan escape routes. Two escape
routes per room are recommended.
• Use a different escape route if closed
doors feel warm or hot to the touch.
• Emphasize that everyone must
escape as quickly as possible. DO NOT
gather any belongings to take with
you, which could prevent you from
getting out safely.
• Crawl and hold your breath as
much as possible to help reduce
smoke inhalation during your escape.
• Meet at a designated outdoor location.
• Emphasize that no one should
re-enter the premises if a re exists.
Warning! Do not re-enter the building if sirens stop.
The sirens in your system are programmed to stop
after a specic time setting expires. This does not
mean it is safe to re-enter the building. Only re
department personnel can determine when it is safe to
re-enter the building.
4

Accidental Alarms
Owning a security system means
changing some habits to avoid causing
accidental alarms. It can be a startling
experience not only from the alarm
itself, but also if local ordinances mandate
that you are ned for such an event.
Most accidental alarms occur when
leaving after arming, or entering the
armed premises when returning home.
For example, you may arm the system
and realize you forgot something.
Instead of disarming the system, you
automatically go get the item you
forgot, only to walk in front of a motion
detector and cause an alarm. Other
accidental alarm causes include:
• Leaving after the exit delay expires.
• Not disarming the system before the
entry delay time expires.
• Exiting or entering through a door
without a delay.
Preventing Accidental Alarms
The following guidelines describe good
habits to help prevent accidental alarms.
• Make sure each system user is
familiar with the location of all system
components and understands how
they operate.
• Pay close attention to siren status
beeps, indicator lights, and messages
on keypad displays which show the
current status of your system.
• Close all doors and windows before
arming the system.
• Exit and enter the premises
only through doors programmed
with delays.
• Make sure pets are not roaming
freely in areas where they may set
off an alarm.
• Make sure to have all necessary
belongings so you can exit immedi-
ately after arming the system.
• Disarm your system immediately
upon entering the armed premises.
Vid e of ied Sec uri ty System Own ers Man ual 5

Basic System Operation
Keypads and Keyfobs are used to
control your system. Keypads allow
complete system control while
Keyfobs allow limited or basic system
control. The following describes the
Keypad and Keyfob button functions.
Note: The keypad display goes blank after
30 seconds of no activity. Press any key to
wake it up, then enter your code, etc.
2
ABC
3
DEF
1
1 2
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
9
WXYZ
0@
M
mYES
ESC
NO
CLR
1
1—arms system to Special Mode 1.
Left Arrow—move backward
through menus/choices.
1 - 9, 0—use for entering access
codes and other numerical
information.
M
m
M/m—change between uppercase and
lowercase characters for text entries.
Keypad Button Functions
@
@
—use for special text
and punctuation entries.
2
2—arms system to Special Mode 2.
House—arms perimeter
protection only.
Right Arrow—move forward
through menus/choices.
CLR
CLR—clear numerical/text entries.
ESC
NO
ESC/NO—back out of a menu
or skip to the next one.
YES
YES—proceed with the
prompted action or accept
the displayed entry/setting.
Keyfob Button Functions
ON—Full arming
1
1—arms system to Special Mode 1 or
audible panic even if Special Mode 1
is not programmed.
OFF—disarms system.
2
2—arms system to Special Mode 2
or silent panic.
Arming modes let you select how much
of your system is turned on or armed.
There are two basic arming modes:
• Full Arming—arms all perimeter
and interior intrusion/ burglary
protection areas.
• Perimeter Arming—arms only
perimeter intrusion/burglary
protection areas to allow normal
activity inside the premises.
• Special Modes 1, 2—arm specic
areas based on programming by
your installer.
ON OFF
1 2
6
Arming Modes
Note: to activate panic alarms
press and hold button 1 or 2.

Arming the System
You can arm your system whether you
are leaving or staying on the premises.
Choose from the following procedures.
Full Arming Mode
Arming to this mode provides
protection for all perimeter and
interior areas. Use this procedure
when leaving the premises.
1. Close all protected doors
and windows.
2. Gather any belongings you want
to take with you.
3. Arm the system:
At the Keypad nearest an entry/exit
delay door, enter:
Access Code +
YES
If arming from a Keyfob,
press the ON button.
The Keypad responds by displaying
ARMING THE SYSTEM, the LED ashes
once every two seconds, and a beep
sounds every second indicating the exit
delay has started and the system is
arming.
4. Immediately leave through the
entry/exit delay door.
Note: If any detection sensors are activated
during the exit delay, the system momen-
tarily stops the arming sequence.
The Keypad display shows DETECTION,
identies the activated sensor(s), then
changes to ESC = REJECT EQUIP, YES = TRY
AGAIN.
If you choose to try again, you must rst
close the identied sensor(s) before pressing
YES.
If you choose to reject(bypass), this means
the identied sensor(s) will not trigger an
alarm during this arming period.
If you do not make a choice after three
minutes, the system automatically bypasses
the identied sensor(s) for this arming
period and arms the rest of the system.
Perimeter Arming Mode
Arming to this mode provides
protection for the perimeter (doors
and windows) only. This allows persons
to stay inside the premises and move
freely without triggering motion
detectors. You can use this mode
whether you are leaving or staying
on the premises. This mode works
well for overnight sleeping periods.
1. Close all protected doors
and windows.
2. Arm the system:
At the Keypad nearest an entry/exit
delay door, enter:
+ Access Code +
YES
The Keypad responds by displaying
ARMING THE SYSTEM, the LED ashes
once every two seconds, and a beep-
sounds every second indicating the
exit delay has started and the system
is arming.
3. If leaving, do so immediately through
an entry/exit delay door.
If staying, notice the Keypad LED
ashes once every two seconds and the
display shows SYSTEM ARMED.
Caution! To avoid an accidental alarm
when arming to this mode and staying inside,
remember to disarm the system before
opening any doors and/or windows.
Note: Keyfobs do not have perimeter arming
modes
Vid e of ied Sec uri ty System Own ers Man ual 7

Basic System Operation
Note: If any door contacts are activated
during the exit delay, the system momentarily
stops the arming sequence.
The Keypad display shows DETECTION,
identies the activated devices(s), then
changes to ESC = REJECT EQUIP,
YES = TRY AGAIN.
If you choose to try again, you must
rst close the identied device(s) before
pressing YES.
If you choose to reject (bypass), this means
the identied devices(s) will not trigger an
alarm during this arming period.
If you do not make a choice after three
minutes, the system automatically arms the
system.
Arming with Protected
Doors or Windows Opened
You can arm your system and still leave
some protected doors or windows open.
For example, you may want a window
open during the night and still arm the
remaining perimeter zones. Or, you may
want a window open during the day
while you are gone and still arm the
remaining perimeter and interior areas.
Note: Arming the system in this manner
means that any protected doors or windows
left open are excluded from the current
arming period and will not trigger an alarm.
1. Open the desired protected doors
and/or windows.
2. Arm the system: If leaving, at the
Keypad nearest an entry/exit delay
door,enter:
Access Code +
YES
If staying, enter:
+ Access Code +
YES
The Keypad responds by displaying
ARMING THE SYSTEM, the LED
ashes once every two seconds, and
a beep sounds every second
indicating the exit delay has started
and the system is arming.
3. The display then shows DETECTION,
identies the activated device(s),
then changes to ESC = REJECT
EQUIP, YES = TRY AGAIN.
4. Press ESC/NO. The system
continues arming, bypassing the
identied zones. If leaving, do so
immediately through an entry/exit
delay door.
Disarming the System
The system must be disarmed upon
entering the armed premises or when
waking up in the morning before
opening any door (such as getting the
morning paper) or window.
When disarming from a Keypad, the
system requires an access code so that
only an authorized system user can
disarm. If you forget your access code
or an unauthorized person tries to
disarm the system, the Keypad stops
accepting access code entries after
three incorrect codes. Thereafter, only
one access code attempt per minute is
allowed until a valid code is entered.
Disarming when Arriving Home
Entering the armed premises must be
done through a designated entry/exit
delay door. This triggers the entry delay
time and keypad and interior siren
beeps, as a reminder to disarm the
system to avoid an alarm.
1. Enter the armed premises through
a designated entry/exit delay door.
8

Keypads and interior sirens start
beeping, indicating the system is
armed and must be disarmed.
2. Disarm the system:
At the Keypad nearest the entry/exit
delay door, enter:
Access Code +
YES
If disarming from a Keyfob, press the
OFF button.
The Keypad shows the date/time
display and DISARMED.
Disarming after
Overnight Arming
Since there are no entry beeps to
remind you in the morning that the
system is armed, waking up inside the
armed premises requires immediate
disarming before opening any protect-
ed door or window. As mentioned earlier,
the Keypad LED ashes once every two
seconds as a reminder that the system
is armed.
1. After waking up, press any Keypad
button (except the red panic button)
to activate the display, which shows
SYSTEM ARMED.
2. Immediately disarm the system:
At the Keypad, enter:
Access Code +
YES
If disarming from a Keyfob, press the
OFF button.
The Keypad shows the date/time
display and DISARMED.
Using Your System
for an Emergency
You can manually activate a panic alarm
anytime the need occurs, whether the
system is armed or disarmed.
For example, if someone experiences a
medical condition or an injury, it is best
to activate the alarm and get trained
professional help to your location. You
can even have your installation dealer
set this up for a specic use based on
your personal needs.
Activating an Alarm in an Emergency
• Press and hold the red panic button
on any Keypad for two seconds, then
release it.
2
ABC
3
DEF
1
1 2
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
9
WXYZ
0@
M
mYES
ESC
NO
CLR
Access Code +
YES
• On a Keyfob, press and hold either the
1 or 2 button for ve seconds, then
release them. If button 1 is pushed the
interior and exterior sirens activate. If
button 2 is pushed the silent panic is
not displayed on the keypad and the
control panel sends an emergency
alarm report to the central monitoring
station.
Keypad
Panic
Button
Vid e of ied Sec uri ty System Own ers Man ual 9

Basic System Operation
Special Arming Modes
The 1 and 2 buttons on Keypads and
Keyfobs can be programmed by your
installer to arm the system according to
your specic needs or lifestyle.
For example, your system may have
divided your home into different
protection areas. Instead of using the
full and perimeter arming modes, these
buttons can be set up to arm a specic
area or combination of areas while still
giving you access to other areas that
will not be armed.
Arming the System
Using Special Arming Modes
1. Close all protected doors and
windows in the affected areas.
2. Arm the system:
At any Keypad, enter:
1
or
2
+Access Code +
YES
The Keypad responds by
displaying ARMING THE SYSTEM,
the LED ashes once every two
seconds, and a beep sounds every
second indicating the exit delay has
started and the system is arming.
3. If leaving, do so immediately
throughan entry/exit delay door.
If staying, notice the Keypad LED
ashes once every two seconds
and the display shows SYSTEM
ARMED.
Voice and Email
Alarm Messages
If your system is armed and an alarm
occurs while you are away, you can
receive the alarm message by phone or
Email.
Phone messages are in the form of a
digital voice that identify the date/time
of the alarm, the type of alarm, and the
device that caused the alarm. Email
messages contain this same informa-
tion and may also include a video le
that you can view.
This section describes how you receive
alarm messages by phone and Email.
Receiving Voice
Alarm Messages by Phone
1. The system goes into alarm and calls
the programmed phone number.
2. When you pick up or answer the
phone, a computer generated voice
identies the date/time of the alarm,
the type of alarm, and the device
that caused the alarm.
3. Press the # button on your phone
to verify you received the message.
Note: If you don’t press the # button, the
system continues reporting the voice alarm
message at regular intervals.
Receiving Alarm Messages by Email
1. The system goes into alarm and
sends an Email to the programmed
Email address.
2. Open the attachment in the Email
message (ASCII le format) using a
word/text processor such as
Microsoft® Word® or Notepad®.
The le identies the date/time of
the alarm, the type of alarm, and
the device that caused the alarm.
3. If a video le attachment is included,
simply double-click on this attachment
to view the video.
10

Once you are familiar with the basic
operation of your system, you can use
the procedures in this section to
customize system operation to t
your needs.
WARNING: If you don’t fully understand
this process, contact your alarm dealer
before you alter any system program-
ming.
• Access Levels and System Menus
• Programming and Deleting
Access Codes
• Creating Schedules
• Viewing the History/Event Log
Access Levels
and System Menus
Access levels determine how much
access you have to menus that let you
view and/or change system information.
Each system access code is assigned to
a specic access level, which determines
accessibility. Access levels and their
associated menus are described below.
Access Levels and System Function
Control
• Level 1—Arm and Disarm only.
• Level 2—Arm, Disarm, Maintenance,
Events Log, Badges Access Codes,
and Alarm Parameters menus.
• Level 3—same as Level 2.
• Level 4—Conguration, Maintenance,
Events Log, Badges Access Codes,
and Alarm Parameters menus
(accessible only by installers).
Menus
To access these menus, press either
arrow button until the desired main menu
(appearing in bold type) is displayed,
then press YES to proceed.
Advanced System Operation
• Maintenance—available in Levels 2
and 3, allows access to the submenus
below for system servicing.
Modifying Date/Time
Maintenance—Replace Battery
Detection Test—Detectors
Equipment Localizing (locate/identify
detectors)
Audio Test Equipment
Select Faulty Equipment
• Event Log—available in Levels 2 and
3, lets you view and send via Email, a
list of all system activity and events.
• Badges, Access Codes—available in
Levels 2 and 3 (only with a valid Level
2 or 3 access code), allows access to
the submenus listed below to let you
add, modify, assign access levels to,
and/or delete system access codes.
Schedules can be created to dene
certain days/times specic access
codes are active.
Recording A Badge/Code
Badges/Codes Conguration
Modify Name—Badge/Code
Access Level
Schedule Authorized
Areas
Alarm (Arming) Modes
Deleting Badges/Codes
• Alarm Parameters—available in
Levels 2 and 3, allows access to the
submenus below that let you view
and/or change the system phone and
IP numbers programmed during the
initial conguration/programming.
You can also enable/disable the
panic button.
Vid e of ied Sec uri ty System Own ers Man ual 11

Advanced System Operation
Changing the System Level
When changing the system level, you
are required to enter an access code
when increasing the level. No code is
required when changing to a lower level.
1. With the display showing the date/
time and current level, press the right
arrow button once. The display shows
ACCESS LEVEL (current level 1 - 4).
2. Press YES. The display shows a
colon (:) between LEVEL and the
number.
3. Press either arrow button until the
desired level number appears, then
press YES. If increasing the level, the
display shows BADGE OR CODE.
4. Enter the appropriate access code
(one assigned to the level selected in
step 3), then press YES. The display
shows the new level.
Programming and
Deleting Access Codes
Your security system allows you to
program up to 20 different access codes.
This gives each individual system user
their own access code with specic
abilities or restrictions.
Just as important, access codes can
and should be deleted when they are
no longer needed. This helps prevent
unauthorized system access and also
helps you maintain the integrity of
your system.
Programming Access Codes
Use the table on the next page to record
and keep track of system access codes.
Access codes must be 4 to 6 digits,
given a name, and assigned to an access
level that determines their abilities or
restrictions. The differences between
access levels are described below.
• Level 1—Arm and Disarm only.
• Level 2—Arm, Disarm, Maintenance,
Events Log, Badges. Access Codes,
and Alarm Parameters menus.
• Level 3—same as Level 2.
• Level 4—Conguration, Maintenance,
Events Log, Badges Access Codes,
and Alarm Parameters menus.
1. Make sure the system is in
Level 2 or 3.
2. Press either arrow button until
the display shows BADGES ACCESS
CODES.
3. Press YES. The display shows
BADGE OR CODE. Enter a Level 2 or
3 access code + YES. The display
shows ENTER A BADGE/CODE.
4. Press YES. The display shows
BADGE OR CODE.
5. Enter the desired new code + YES.
The display shows CONFIRM THE
CODE.
6. Re-enter the new code + YES. The
display shows CODE NAME:
7. Enter the desired user name + YES.
The display shows [NAME] RECORD
ED, then returns to RECORD
ING A BADGE/CODE.
8. Press the right arrow button once.
The display shows BADGES/CODES
CONFIGURATION.
9. Press YES. The display shows MODIF
NAME BADGE CODE.
10.Press the right arrow button once.
The display shows ACCESS LEVEL 3.
11. Press YES. The display shows
ACCESS LEVEL LEVEL: 3.
12.Press either arrow button until the
desired level is displayed,then press
YES. The display shows the new
level assignment.
12

13.Press ESC/NO three times to
return to BADGES ACCESS CODES.
14. Repeat steps 2 - 12 to continue
programming codes.
You can change the access level
assignments as needed anytime, using
the following steps.
1. Make sure the system is in Level 2 or 3.
2. Press either arrow button until the
display shows BADGES ACCESS CODES.
3. Press YES. The display shows BADGE
OR CODE. Enter a Level 2 or 3 access
code + YES. The display shows
ENTER A BADGE/CODE.
4. Press the right arrow button once.
The display shows BADGES/CODES
CONFIGURATION.
5. Press YES. The display shows the
rst programmed access code.
6. Press either arrow button until the
desired code appears, then press
YES. The display shows MODIF
NAME BADGE/CODE.
7. Press the right arrow button once.
The display shows ACCESS LEVEL 3.
8. Press YES. The display shows
ACCESS LEVEL LEVEL:3.
9. Press either arrow button until the
desired level assignment appears,
then press YES. The display shows
the new level assignment.
10. Press ESC/NO.
11. Repeat steps 5 - 9 for additional
code congurations.
Code No Code Name Level
Changing Access Level Assignments
Vid e of ied Sec uri ty System Own ers Man ual 13

Advanced System Operation
Changing Access Code
Alarm Arming Mode Restrictions
After programming a new access code,
all alarm (arming) modes are available
using the code. You can restrict alarm
(arming) modes for any access code,
using the following steps.
1. Make sure the system is in Level 2 or 3.
2. Press either arrow button until the
display shows BADGES ACCESS
CODES.
3. Press YES. The display shows
BADGE OR CODE. Enter a Level 2 or
3 access code + YES. The display
shows ENTER A BADGE/CODE.
4. Press the right arrow button once.
The display shows BADGES/CODES
CONFIGURATION.
5. Press YES. The display shows the
rst programmed access code.
6. Press either arrow button until the
desired code appears, then press
YES. The display shows MODIF
NAME BADGE/CODE.
7. Press the left arrow button once.
The display shows ALARM MODES
ENABLED.
8. Press YES. The display shows
SPECIAL MODE 1 ENABLED.
9. Press either arrow button until the
desired mode appears, then press
YES. The display shows ENABLED:
10. Press either arrow button once. The
display changes to DISABLED.
11. Press YES. The display shows the
new alarm (arming) mode setting
without the colon.
12. Repeat steps 6 - 11 for other code
restriction changes.
Deleting Access Codes
Delete access codes as needed anytime,
using the following steps.
1. Make sure the system is in Level 2 or 3.
2. Press either arrow button until the
display shows BADGES ACCESS CODES.
3. Press YES. The display shows BADGE
OR CODE. Enter your level 2 or 3
code + YES. The display shows
ENTER A BADGE/CODE.
4. Press the left arrow button once.
The display shows DELETING
BADGES/CODES.
5. Press YES. The display shows the
rst programmed access code.
6. Press either arrow button until the
desired code appears, then press
YES. The display shows DELETING
CODE.
7. Press YES again. The display shows
CODE DELETED.
8. Repeat steps 6 - 7 to continue
deleting codes.
14

Creating Schedules
Schedules allow you to control when
a specic access code can be used to
arm and disarm the system. A schedule
consists of a day, beginning time, and
ending time that the specic access code
can be used. Up to ve schedules can be
programmed for each access code.
Use the tables on page 16-17 to ll in the
necessary schedule information for each
code. Enter this information using the
procedure below.
1. Set the system to Level 2 or 3.
2. Press the left or right arrow button
until the display shows BADGES
ACCESS CODES, then press YES.
The display shows BADGE OR CODE.
3. Enter the appropriate Level 2 or 3
access code, then press YES. The
display shows ENTER A
BADGE/CODE
4. Press the right arrow button once.
The display shows BADGES/CODES
CONFIGURATION.
5. Press YES. The display shows the
rst access code.
6. Press the left or right arrow button
until the desired code is displayed,
then press YES. The display shows
MODIF NAME BADGE/CODE.
7. Press the right arrow button twice.
The display shows SCHEDULE
AUTHORIZED.
8. Press YES. The display shows
SELECT/MODIFY SCHEDULES.
9. Press the right arrow button once.
The display shows ENTER A NEW
SCHEDULE.
10. Press YES. The display shows
BEGIN SCHEDUL 1 Mon.
11. Press either arrow button until the
desired weekday appears, then press
YES. The display shows BEGIN
SCHEDUL 1 Day= 00:00.
12. Press either arrow button until the
desired hour appears, then press
YES. The display does not change.
13. Press either arrow button until
the desired minutes appear, then
press YES. The display shows END
SCHEDUL 1 MON.
14. Press either arrow button until the
desired day appears, then press
YES.
15. Press YES. The display shows
END SCHEDUL 1 Day= 00:00.
16. Press either arrow button until the
desired hour appears, then press
YES.
17. Press either arrow button until the
desired minutes appear, then press
YES. The display shows SCHEDULE
ENTERED!, then returns to ENTER
A NEW SCHEDULE.
18. Repeat steps 10 - 17 for additional
schedule programming.
Vid e of ied Sec uri ty System Own ers Man ual 15

Code No. Schedule No. Day Start Time End Time
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Advanced System Operation
16

Code No. Schedule No. Day Start Time End Time
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Vid e of ied Sec uri ty System Own ers Man ual 17

Advanced System Operation
Events are any system activity such
as arming, disarming, alarms, access
codes entered, and system program-
ming changes. The control panel uses
built-in memory to record each system
event and the date/timeit occured. This
log cannot be cleared or erased and
accumulates events for up to a full year.
As additional events occur, the control
panel automatically deletes the oldest
event. This ensures an accurate one
year history.
You can view the contents of the
history/event log using a system
Keypad or by instructing the system
to send the complete event log as
an Email.
Viewing by Keypad
This method lets you view the most
recent events.
1. Set the system to Level 2 or 3.
2. Press either arrow button until the
display shows EVENTS LOG.
3. Press Yes. The display shows
SELECT LAST EVENTS.
4. Press Yes. The last or most recent
event is displayed.
5. Press the left arrow button to view
previous events.
6. When nished, simply stop pressing
buttons. The display returns to the
date/time and current status, then
goes blank to conserve battery power.
18
Sending History/Log
File by Email
This method lets you send a complete
history/log le to a desired Email
address for viewing. The Email includes
an attachment (in ASCII le format)
that can be opened using a word/text
processor such as Microsoft® Word®
or Notepad®
Contact your alarm dealer
for details.