Videofied XTO Series User manual

XTO / XTO-IP ALARM PANEL SERIES
INSTALLATION MANUAL
DOC. - REF. 230-XTO-IP
MODIF. DATE : SEPTEMBER 2018
FIRMWARE VERSION : XLP.04.04.00.XXX AND
LATER
1

2
XTO / XTO-IP Alarm panel
INSTALLATION MANUAL
Description
The XTO / XTO-iP is a fully wireless alarm system. It is powered by standalone Lithium batteries.
This panel has been designed for outdoor installations, with its weatherproof casing and extended operating
temperature range.
With the Motion Viewers™ and Videofied®range of products, the XTO-iP panel provides video verification in case
of intrusion.
Technology
The XTO-iP alarm panel, like all Videofied devices, uses the S2View®patented technology. Which is an interactive
wireless and AES encrypted technology ensuring signal integrity and optimal security.
The reliability of the signal is guaranteed thanks to the two-way radio frequency transmissions with all the peripherals
of the Videofied®product line.
The integrated antennas allow the system to be totally wireless, thus preventing from the system beeing inelegant
and cumbersome, and eliminating the installation problems.
The jamming detection feature identifies any intentional jamming from a third party. On the other hand, the
supervision feature consists of transmitting signals between every device of the system and the alarm panel XTO-iP.
Through the supervision, the detectors transmit every 8 minutes a presence signal.
The entire RSI VIDEO TECHNOLOGIES team wishes you a successful installation.
INTRODUCTION

3
XTO / XTO-IP Alarm panel
INSTALLATION MANUAL
SUMMARY
Introduction............................................................................................................2
Summary..................................................................................................................3
1.
Panel setup.........................................................................................................................4
1.1 SIM card installation..........................................................................................................................4
1.2 Panel bracket mounting.......................................................................................................................4
1.4 Powering and initialization...................................................................................................................5
1.5 Pairing the keypad...............................................................................................................................6
1.6 Cover locking.......................................................................................................................................6
2. XTENDER Mode................................................................................................................................................................7
3.
Panel programming...................................................................................................................................8
ETHERNET parameters configuration.........................................................................................................................................12
XTENDER mode configuration...............................................................................................................................................14
4. XTO-iP features guide....................................................................................................................16
4.1 Get to access level 4......................................................................................................................16
4.2 How to Arm/Disarm the system.........................................................................................................16
4.3 Arming and Siren Mode Configuration.............................................................................................17
4.4 Manage badges and access codes...................................................................................................18
4.5 Delete the keypad or any other device............................................................................................20
4.6 Read the event log.............................................................................................................................21
4.7 Programmable inputs and outputs.....................................................................................................21
4.8 Golden rules........................................................................................................................................22
5. Transmitted events list....................................................................................................................23
6. 2G3G4G error codes......................................................................................................................24
7. Technical specification and security notes...............................................................................25

4
INSTALLATION MANUAL 1. PANEL SETUP
XTO / XTO-IP Alarm panel
1.2 Panel bracket mounting
The four screwholes here opposite are intended to
mount the bracket, the latter beeing used to attach the
panel to the wall or a pole.
Mounting the panel is not required for programming.
Screwholes
1.1 SIM card installation
Before removing the front cover from its box, Put the SIM card
on the plastic base (Take care to respect the right direction).
DO NOT insert or remove the SIM card while the panel is
powered.

5
INSTALLATION MANUAL 1. PANEL SETUP
XTO / XTO-IP Alarm panel
1.3 Powering and initialization
•The panel is powered either with 4 LSH20 Lithium batteries or mains powered with 4 alkaline backup batteries.
•Always replace all 4 batteries at once. Mixing new and used batteries can severely damage the panel (risk of explosion).
•Press and hold the PROGRAMMING BUTTON for 10 seconds, until the indicator LED blinks twice.
•The panel is now reset, a CMA, XMA or XMB has to be enrolled to configure the panel.
Programming button
Mains Power Supply
Lithium batteries
Do not use Lithium batteries when the panel is mains powered
When using Ethernet, only power yor panel with the mains power supply.

6
INSTALLATION MANUAL 1. PANEL SETUP
XTO / XTO-IP Alarm panel
1.5 Cover locking
Place and screw the cover on
its support.
•Press the XTO programming button and release for the enrollment of a programming
keypad.
•Insert all LS14500 Lithium batteries into the keypad.
•Do not mount the keypad. It will display one of the following screens:
1.4 Pairing the remote keypad
RSI (c) 2013
videoed.com <=========XX=========>
or
•Press on both CLR and ESC NO keys at the same time and release. The indicator
LED on the keypad will blink rapidly. Wait for the keypad to pair.
•If the keypad doesn’t pair up with the panel and shows «XX», it certainly means
that it is still paired to another system and needs to be reset. Take the batteries out,
and press repeatedly on the keypad tamper switch. Then proceed to the above steps.
Screw locking

7
XTO / XTO-IP Alarm panel
INSTALLATION MANUAL
Arming O/P 1
Arming O/P 2
Existing Host
panel
2.1 Standalone Mode
2.2 XTENDER Mode (From the host)
In this functioning mode,
the XTO-iP panel works as a
standard hybrid alarm system
with 25 wireless peripherals
and 3 programmable inputs.
It is a totally standalone alarm
system.
The panel can be used as standard standalone alarm system but it can also be connected to an existing alarm system capable of
latching a 9-12Vcc* voltage used for its arming/disarming.
When the panel is used in XTENDER mode, the system will only be able to arm and disarm by latching 9-12Vcc to its arming inputs
Arming Input 1 and/or Arming Input 2.
When the voltage switches to 0V, the panel will disarm automatically.
On a programmed panel, you can choose between standalone and XTENDER modes from the menu :
CONFIGURATION (LVL 4) > GENERAL PARAMETERS > XTENDER
*When using an XTO-iP in XTENDER
mode, the panel has to be powered
by the mains power supply.
2. XTENDER MODE

8
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
Keypad Display Actions and comments
KEYPAD 1
RECORDED
RADIO RANGE TEST?
RF TEST
x/9
RF TEST
9/9
RADIO RANGE TEST?
INSTALLER CODE
4 TO 6 DIGITS
THEN OK/YES
INSTALLER CODE :
< - LANGUAGE : - >
ENGLISH (UK)
The system can also be programmed in : french, italian,
german, dutch, spanish, swedish, portuguese, danish,
czech and polish.
The language can be changed at any time once the panel
is programmed in the MAINTENANCE menu.
The Radio Range test must be run during the device
learning process in order to ensure proper pairing with
the control panel. This test measures the strength of
communication between the device and the control
panel. The keypad will display a real time radio range
value on a scale of 9.
To receive the most accurate results you must run the radio
range test for at least 30 seconds.
Result must be 8 out of 9 or better for reliable
transmission.
Using the Alphanumeric Keypad, enter the Installer Code
of your choice.
The Installer Code will be used for all future maintenance
and configuration.
This code is important to keep track of.
There is no back door or Default codes to the
system
Please refer to the restriction rules for codes (Chapter 4.5).
Some codes are already used by default and therefore
cannot be used.
OK or YES
OK or YES
Please wait
OK or YES
ESC
NO
for language selection
OK or YES
CONFIRM CODE
OK or YES
OK or YES

9
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
Keypad display Actions and comments
CODE NAME :
OK or YES
ACCESS 1
REGISTERED
You may name the installer code using the Alphanumeric
Keypad.
If using automatic setting (called installer default list), enter
the name of the list.
Warning : If the wrong installers list name is used it
cannot be set later, the system must be defaulted.
Leaving the name blank by pressing
ESC NO , it will be
named ‘ACCESS 1’ by default.
Please wait
ADJUSTING DATE
AND TIME
DATE (YEAR):
12/ /
To set the year
OK or YES
DATE (MONTH):
13/01/
To set the month
OK or YES
You may proceed in the same way for:
Day, Hour and Minutes.
13/10/14 10:47
ENTRY COMPLETE !
ACCOUNT NUMBER :
CONNECTED TO
MONITOR. STATION?
OK or YES
Use the Alphanumeric Keypad to enter in a 4-8 digit
account number provided by the Central Station.
ACCOUNT NUMBER :
567001
OK or YES
ESC
NO

10
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
TEST (hour) :
04:
CODE/STATE
MODIFICATION?
Test Periodicity: 1 hour, 12 hours, 24 hours, 48 hours, 7
days or no tests.
We suggest a 24 hours periodic test call.
PERIODIC TEST
PERIODIC TEST :
24 HOURS
To select periodicity
OK or YES
OK or YES
TEST (minutes) :
04:15
OK or YES
OK or YES
CODE/STATE
MODIFICATION
Keypad display Actions and comments
The CODE/STATE MODIF. menu is to configure the
transmitted events to the monitoring station, use the
arrow keys to toggle between events and
OK or YES to
modify.
ALARM: event transmitted upon occurrence.
ALARM/END: event is transmitted on occurrence and on
event restoral.
NOT TRANSMITTED: event is not transmitted, however it
will appear on the keypad.
Please liaise with your Monitoring Station to ensure
that the requested events to transmit are correctly
set.
Events list
ESC
NO
SERVER
ADDRESSES ?
OK or YES
Wait
ESC
NO

11
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
SERVER
ADDRESSES ?
The IP1 address,Domain name 1 and/or Port 1 are provided by the monitoring station.
Leave Port details at 888 unless otherwise instructed.
Press
OK or YES to enter/modify the parameter then OK or YES for validation.
WARNING : You will use either an IP address or a Domain name but not both, leave the
Domain name blank if an IP address has already been entered.
Press on the right arrow to configure IP/Domain name 2 and PORT2 (for the back-up server),
and IP/Domain name TMT and PORT TMT (to configure remote maintenance server).
ESC
NO
OK or YES
ESC
NO
STR ATEGY:
ETH+2G3G4G
2G3G4G
PARAMETERS ?
ESC
NO
OK or YES
TEST IN PROGRESS
END = OK/YES
2G3G4G LEVEL
5/5
2G3G4G LEVEL ?
2G3G4G LEVEL ?
OK or YES
The APN Code (Access Point Name), User Name and Password are supplied by the
mobile operator. Please make sure you have entered the code exactly as indicated by your
local SIM card operator.
Press
OK or YES to enter/modify the parameter then OK or YES for validation.
Note: When entering your SIM card settings, both APN codes, username and
password fields are case sensitive! It makes a difference between UPPER and lower
case letters.
To switch between UPPER and lower case, use the M/m key from CMA keypad or hold a digit key
(0-9) for XMA/XMB.
Once the 2G3G4G test completed, the keypad will display one of the following results :
- A level between 0/5 and 5/5.
- A GPRS Error code (please see Chapter 7 : 2G3G4Gerrors codes and contact your
technical support).
If the screens shuts down, press any key to light it up except OK or YES , ESC NO or CLR .
The 2G3G4G level test can last several minutes. Do not interrupt the test or remove the SIM
card during the test.
IMPORTANT : Videofied will require a 3/5 grade or better for reliable transmission
of Video alarms.
ESC
NO
2G3G4G
PARAMETERS ?
OK or YES
How the alarms and videos are transmitted to the monitoring station ?
ETH+2G3G4G : Ethernet transmission with GPRS backup.
2G3G4G : GPRS transmission only (if the Ethernet connection is not used).
ETH : Ethernet transmission only (only if GPRS is not used).
Warning : the transmission mode “Ethernet only” is not recommended.
ESC
NO
IP1 ADDRESS
0.0.0.0
DOMAIN NAME 1 PORT 1
888
APN CODE
internet-entrepr
USER NAME
orange
PASSWORD
orange

12
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
IP
PARAMETERS ?
OK or YES
ETHERNET parameters configuration
DHCP :
ENABLED PANEL IP
DHCP :
DISABLED
OK or YES
IP MASK
GATEWAY
PRIMARY
DNS
SECONDARY
DNS
IP
PARAMETERS ?
ESC
NO
ETH. STATUS?
TEST IN PROGRESS
END = OK/YES
ESC
NO
OK or YES
PANEL IP
XXX.XXX.XXX.XXX
ETH. STATUS?
ESC
NO
ESC
NO
During this test, the panel tries to connect to the
local Ethernet Network. The result of this test
can be:
•If the connection is successful: the local IP
of the panel will be displayed (you can
display other Ethernet parameters with the
arrows ).
•ETHERNET OFF NO STATUS : the
Ethernet module is switched off. Please
verify that the Ethernet cable is connected
and try again.
•NETWORK/CABLE MISSING : the panel
doesn’t detect Ethernet Cable or Network.
Bysettingthe DHCPas ENABLED,
a new IP address will be assigned
dynamically to the panel every
time it connects to the network.
Network parameters will not be
asked.
If the router forces a static IP
address for the panel, there will
then be a need to define DHCP
as DISABLED. You will then need
to fill in the following network
parameters fields : Panel IP, IP
Mask, Primary DNS, Gateway
and Secondary DNS.
Warning: Verify that the IP
address selected is available on
the Network and accepted by the
router.
OK or YES

13
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
Your choice will depend on how you are arming the
system :
Standalone : Will make the XTO-iP a completely
independant system controlled by arming
and disarming using Videofied peripheral
devices(keyfobs, keypads, badge,readers).
From the host : Will make the XTO-iP panel a
piggyback/xtender system that will only arm and
disarm off the latching of 9-12V on the arming
inputs 1 & 2.
COMPATIBILITY
EN 50131 NORMS ?
AREAS CONFIGURATION
AREA 1 NAME :
ESC
NO
OK or YES
OK or YES
OK or YES
ARMING PROFILE :
STANDALONE
ARMING PROFILE :
FROM THE HOST
EXIT DELAY :
45 sec
For the selection
OK or YES
ENTRY DELAY :
15 sec
For the selection
Please go to page 15 if you chose
STANDALONE
OK or YES Please go to page 14 if you chose
FROM THE HOST
For full compatibility with EN50131, press OK or YES .
Otherwise, press
ESC NO.
Press ESC NO to default the area names.
Enter the name of the area 1 and
OK or YES .
Repeat the procedure for areas 2,3 and 4.
For further details, please refer to chapter 4.3.
Other values are available: 2 min, 1 min, 45 sec.
Other values are available: 2 minutes, 1 minutes, 45
seconds,30 seconds or 15 seconds.

14
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
XTENDER mode configuration
ARMING PROFILE :
FROM THE HOST
MODE SLOW : The panel will arm each device one at
a time saving battery life. We recommend this mode.
MODE FAST : The panel will arm all devices at the
same time. This mode increases significantly the
battery consumption.
OK or YES to choose the parameter.
ENTRY DELAY
VALUE (0-255) :
(000) : _
Enter the value for your Entry Delay up to 255 seconds
and press
OK or YES.
Note : In From the Host mode, the entry/exit delay are
dealt by the master system.
TRANSMISSION DELAY
VALUE (0-600) :
(000) : _
ARMING CONFIRMATION
VALUE (0-240) :
(0) : _
Arming Confirmation is the number of seconds the
system will wait to arm after voltage is latched on
the arming input. This feature can be used as an exit
delay, we suggest you to enter the same value as
your master system exit delay.
Enter the value you would like for the Arming
Confirmation and press
OK or YES.
OK or YES
ARMING MODE
MODE :
SLOW
MODE :
FAST
OK or YES
OK or YES
OK or YES
The transmission delay value sets the delay between
the detection of an event and its transmission to the
monitoring center.
Except when specifically required, please enter 0.
Enter the value you would like for the Transmission
Delay and press
OK or YES.
For further information about the programmable inputs and outputs, please consult the following
application notes available on our support website:
240-XT - APP NOTE - XTENDER CONFIGURATION MODE

15
INSTALLATION MANUAL 3. XTO-IP PANEL PROGRAMMING
XTO-IP Alarm panel
PRESS PROGRAM
BUTTON OF DEVICE
RECORDING
DEVICES
ENTERING A NEW DEVICE ?
BADGE ENTERED ?
RECORDING A
NEW BADGE ?
END OF
CONFIGURATION
Each device has a unique programming button or a
specific manipulation. Please refer to the Installation
Sheet for the device you would like to program.
Please check the radio level of each device on its final
location. The result must be 8 out of 9 as a minimum
(Please refer to the Radio Range section, page 8 for
further details).
Each system can embrace a maximum of 25 devices,
programming keypad included.
Press
OK or YES to enter a new device or ESC NO to
move to the next step.
ESC
NO
ESC
NO
ESC
NO
Aer initial programming has been completed, the system
cannot be armed or disarmed until a user code or badge
is entered (the installer code cannot arm or disarm the
system).
Press
OK or YES to register one or more badges.
ESC NO if you’re not using any badges.
If you wish to use an user code, please skip this step
and when initial programming is completed go to the
BADGES/ACCESS CODES menu (please refer to chapter
4.4 for further details).
Badges and codes are limited to 19 for user (level 2 or 3) +
1 installer code.
OK or YES
OPERATION
COMPLETED ?
SYSTEM CHECK
IN PROGRESS
INSTALLATION SUCCESSFUL !
Before completing programming make sure that no device
is tampered. Each device must be closed and its LED
indicator shall be turned off.
Aer initial programming has been completed, make
use of the menu overview document (available on our
technical support website), to see full programming
options.
OK or YES

16
INSTALLATION MANUAL 4. FEATURES GUIDE
XTO-IP Alarm panel
4.2 How to Arm/Disarm the System
When in standby mode, the system can be armed with the remote keypad, the remote keyfob
and/or the remote badge reader.
Full arming with
user code Full arming with badge Special Arming 1 Special Arming 2
With remote
keypad
Enter your user code
and press
OK or YES
Present your badge on
the keypad
( XMB model only)
Press /
enter your user code
and press
OK or YES
Press /
press
OK or YES and enter
your user code
With remote
badge reader
BR250
N/A Present your badge on
the badge reader N/A N/A
With remote
keyfob
N/A N/A Press Press
4.1 Get to Access level 4
Tue 29/10 11:23
DISARMED LVL:1
ACCESS LEVEL
1
ACCESS LEVEL
LEVEL : 1
ACCESS LEVEL
LEVEL : 4
OK or YES
OK or YES
To unlock and get access to the installer level 4, you need to successively enter TWO codes
(in any order) :
• INSTALLER CODE (entered during intial programming).
• USER CODE (Level3): the user must authorize the installer to get access to the
configuration of his panel.
OK or YES
BADGE OR CODE

17
INSTALLATION MANUAL 4. FEATURES GUIDE
XTO-IP Alarm panel
When in the ‘Arm From Host’ mode, the Videofied system will only arm and disarm when 9-12v is supplied and sustained.
When both arming inputs are supplied voltage at the same time the Videofied Keypad display will show ‘SYSTEM ARMED.
When only one arming input is supplied voltage the Videofied Keypad display will show ‘PART LVL #’
• Arming Input 1 will arm/disarm Areas 1 & 2 – Area 1 is delayed by default
• Arming Input 2 will arm/disarm Areas 3 & 4– Area 3 is delayed by default
4.3 Arming and Siren Mode Configuration
For each arming mode, it is possible to specify how each of the 4 areas will be armed and how the system will behave during an alarm.
Areas : 1 2 3 4 Each time you press the corresponding number, the system will toggle the arming
state for the respective area.
State : A A A A Press
OK / YES aer this configuration step. The system will then display what siren mode
will be in effect for this special profile. Select the siren mode using the direction arrows then
press
OK / YES .
A Armed
DDisarmed
PPerimeter
(by default : all opening contacts*)
E
External
(by default : all opening contacts
with external access*)
* You can set your devices as : External, Perimeter, ou External +Perimeter. Please go to the menu:
CONFIGURATION (LVL 4) -> AREAS AND DEVICES -> DEVICES -> DEVICES CONFIGURATION -> DEVICE TYPE
Siren Immediate triggering of all sirens
Delay Beeps Entry/Exit delay beeps, then triggering of all sirens
Silent No Sirens, No Beeps
Without Siren Beeps on the keypad only
•Use the to go to menu :
CONFIGURATION (LEVEL 4) > SPECIAL ARMING MODES > FULL ARM, SP1 or SP2 use direction arrows to select the arming mode you
want to modify and
OK / YES .
•There are 3 different arming modes :
FULL ARM : Arming of all areas and all devices. Use a badge or a user code and press
OK / on the XMA/XMB keypad or the
YES key on the CMA keypad.
SP1 : Partial Arming (1) is enabled by entering the user code and pressing on the XMA/XMB keypad, the key on the CMA
keypad or on the remote keyfob RC.
SP2 : Partial Arming (2) is enabled by pressing the key on a XMA/XMB keypad, on a CMA keypad, or on the remote
keyfob RC.

18
INSTALLATION MANUAL 4. FEATURES GUIDE
XTO-IP Alarm panel
4.4 Manage badges and access codes
Codes and badges get rights access to one of the 4 available levels of access.
Access Level Definition & Rights
LVL 1 Standby Level
LVL 2
Restricted USER level, where it is only possible to arm/disarm the system.
LVL 3
USER level, where it is possible to arm/disarm the system, check the event log, test the devices.
Modifications of the settings are not possible at this level.
User Level 3 can create Level 2 or Level 3 access codes or badges.
LVL 4
INSTALLER level, where it is possible to modify the setup of the panel. .
To access Level 4, the approval of a Level 3 oe Level 2 user is required.
Installer Level 4 can create the first Level 3 access code only.
How to return to the LVL1?
•Aer 1 min of no use of the keypad and no tests running, the display returns to the standby display and LVL1.
•When standby display, if the ESC NO key is held during 5s, the level is changed to LVL1.
Access Level

19
INSTALLATION MANUAL 4. FEATURES GUIDE
XTO-IP Alarm panel
Enter a new end user Badge/Code Delete an end user Badge/Code
ENTER A
BADGE/CODE
Press twice on the right
arrow
DELETING
BADGES/CODES
Badges/codes list
Select badge/code
then
OK or YES
DELETING CODE
ACCESS 5
CODE
DELETED
BADGE OR CODE
CODE NAME :
CONFIRM THE
CODE
ACCESS 2
ENTRY COMPLETE
BADGES
ACCESS CODES
ENTER A
BADGE/CODE
Enter a 4-6 digit user code and
OK or YES
or present a badge in front of the reader until
you hear the registration beep.
OK or YES
OK or YES
OK or YES
OK or YES OK or YES
OK or YES
When a code is created (1000 for example),
the 2 next codes and previous codes (0998,
0999, 1001 and 1002) will be automatically
reserved.
The +1 code (1001) is used for disarming
under duress.
The +2 code (1002) is used for panic.
The -1 and -2 codes (0998 et 0999) are
reserved to prevent conflicts when creating a
new user code.
Reserved Codes
000000
From 9998 to 9999
From 99998 to 99999
From 999898 to 999999
From 314157 to 314159
All user codes +1
All user codes +2
All user codes -1
All user codes -2
Reserved Codes
Up to 19 codes (or badges) can be registered
into the panel with the engineer code.
A code has 4 to 6 digits (0 to 9).
The table presents the reserved code
possibilities that cannot be used.
Those codes are used for maintenance or as
panic/duress codes.
A total of 186 codes are forbidden.

20
INSTALLATION MANUAL 4. FEATURES GUIDE
XTO-IP Alarm panel
4.5 Delete the keypad or any other device
You can now remove the batteries from
the device
ACCESS LEVEL
4CONFIGURATION
GENERAL
PARAMETERS
OK or YES
to select the device
and press
OK or YES
< = = = = XX = = = = >
DELETE
AREAS AND
DEVICES
DEVICES
ADD A NEW
DEVICE
DEVICE
CONFIGURATION
A1 : KEYPAD
KEYPAD 1
OK or YES
OK or YES
OK or YES
Devices list
OK or YES
OK or YES