Videofied XL 3.1 Owner's manual

Videofied XL Programming
Module 3:1

MODULE 3.1 : VIDEOFIED XL SYSTEM
PROGRAMMING
Learning Outcomes :
1. Knowledge of Videofied XL Panel and associated
peripherals
2. Ability to program a Videofied XL System
3. Ability to add and delete Videofied devices
4. Ability to perform radio (RF) device range tests
5. Ability to perform functional device tests
6. Knowledge in the placement of Videofied MotionViewers

1. GOLDEN RULES - XL
1. Devices in Area 1 are ALWAYS subject to Entry and Exit delay.
2. If a Keypad or Badge Reader is entered into an Area, then all the devices in this Area are
also subject to Entry/Exit delays.
3. Never place the panel near an electric switchboard: there is a possibility of interference with
the Radio and GPRS modem.
4. Place the alarm panel at the most central location of the site to be protected. (guarantees a
better propagation of the radio)
5. Never record the same device twice without having first deleted the device off the panel.
6. Record a maximum of 19 peripheral devices and 19 User codes/badges (XL panels)
7. You are limited to 3 keypads or badge readers or combination there-of.
8. Installation height for Indoor MotionViewers is 2.1 to 2.35mtrs.
9. Installation height for Outdoor Motionviewers is 2 –3mtrs. NOTE: Suited to protect assets
not areas, and should be angled down to cutoff the PIR view to10mtrs.
10. Never mount the keypad at the beginning of installation so that you can walk around with it
during programming.
11. Always clean the camera lens after installation (with a clean and dry piece of cloth, without
pressing on the lens)
12. The keypad becomes inactive after 30 seconds of inactivity, in order to make the display to
reappear, press on the [YES] key

2. What we need to begin?
•Videofied XL Panel
•8 x Energizer ‘D’ cell alkaline batteries
•Wireless keypad (CMA701)
•Indoor MotionViewer (DCV701)
•Outdoor MotionViewer (DCV751)
•Wireless Universal Device –Reed (CT701)
•Remote Control (RC701)
•Badge Reader (BR751)
•Badge –Proximity Tag
•18 x ‘AA’ Saft lithium batteries (LS14500)
•SIM Card (GPRS activated) Security PIN Disabled
•Monitoring Station Details : Account Number & IP OR Domain Name
•XL Programming Manual (Download at
www.videofied.com.au/downloads/manuals )

Videofied XL Panel

3. Programming XL Panel
i. Refer to the XL programming manual Page 3
ii. Remove the XL panel from the box
iii. Insert SIM card into the panel as shown:

3. Programming XL Panel
IV. Assemble the XL panel
Affix rear panel on the wall and clip in front of panel

3. Programming XL Panel
V. CONNECT POWER LEAD
Connect power cable and insert batteries. Keypad should
light up and flash (a beep should be heard).

3. Programming XL Panel
VI. DEFAULT THE PANEL
Hold down the PROGRAM BUTTON on the panel for 10
seconds until the keypad beeps again and lights up all the
keys of the panel keypad.

3. Programming XL Panel
VII. RECORD KEYPAD
Press and release instantly the PROGRAM BUTTON of the
panel again to switch to keypad registration mode.

3. Programming XL Panel
• Insert the 3 Lithium LS14500 batteries in the keypad.
• Do not mount the keypad.
• Simultaneously press the [CLR] and [ESC NO]
buttons on the keypad, until the keypad’s LED flashes,
then release. (Usually 2 –5 seconds)
IIX. RECORD THE KEYPAD (Ref. Keypad installation data sheet)
PRESS [CLR] & [ESC NO]
SIMULTANEOUSLY

3. Programming XL Panel
IX. BEGIN PROGRAMMING - RADIO RANGE TEST
KEYPAD 1
RECORDED
KEYPAD DISPLAY
PRESS
<LANGUAGE>
ENGLISH
RADIO RANGE
TEST?
RADIO RANGE
X/9
PRESS
PRESS Perform a radio range test between the XL
panel and the keypad. Must not be less
than 5/9 radio strength.
Allow 30 seconds for signal strength to
stabilize.

3. Programming XL Panel
X. ENTERING INSTALLER CODE
ENTER THE
INSTALLER CODE
KEYPAD DISPLAY
WAIT
4 to 6 DIGITS
THEN YES
INSTALLER CODE:
CODE NAME :
WAIT
There is no default installer code, it is what
is entered at this stage.
Installers code will take up 1 of the 20 user
code/proximity badge slots

3. Programming XL Panel
XI. ADJUSTING DATE & TIME
ADJUSTING
TIME AND DATE
KEYPAD DISPLAY
DATE (YEAR) :
00/ / Repeat for MONTH, DAY, TIME and MINUTES

3. Programming XL Panel
XII.MONITORING STATION SETTINGS
CONNECTED TO
MONITORING STATION?
KEYPAD DISPLAY
PRESS
ACCOUNT NUMBER:
PERIODIC TEST
PERIODIC TEST:
24 HOURS
Enter the client account number provided by monitoring
station then
Hourly Periodic tests will significantly
shorten the battery life

3. Programming XL Panel
XII. MONITORING STATION SETTINGS..
TEST HOUR:
00:0
KEYPAD DISPLAY
CODE/STATE
MODIFICATION?
By default events that are transmitted to the monitoring station are:
DEVICE (Intrusion), PANIC, TAMPERS, PERIODIC TEST, LOW PANEL
BATTERIES, LOW DEVICE BATTERIES, SUPERVISION FAULT.

3. Programming XL Panel
XIII.AREA CONFIGURATION
AREA
CONFIGURATION
KEYPAD DISPLAY
AREA NAME 1 :
Repeat this for Areas 2, 3 and 4.
Areas are the logical areas that devices will reside within. For example
Area 1: Entry Foyer (delayed)
Area 2: Front Offices
Area 3: Warehouse
Area 4: Show Room
Area 1 is always an entry exit delay area.
Enter the name of Area 1 and then

3. Programming XL Panel
XIV.ENTRY –EXIT DELAY
EXIT DELAY:
45 sec
KEYPAD DISPLAY
ENTRY DELAY:
15 Sec
Exit Delays can be
either 45 sec, 1min or
2min
Entry Delays can be
either 15 sec, 30 sec,
45 sec, 1min or 2min

3. Programming XL Panel
XV.GPRS PARAMETERS - CONFIGURATION
GPRS
PARAMETERS?
KEYPAD DISPLAY
PRESS
APN:
•APN (Access Point Name) information entered
depends upon your SIM service provider.
•APN information must be entered in lower case
•A username and password is used for corporate
network
Service
Provider
APN
USERNAME
PASSWORD
Telstra
telstra.wap
Telstra
Corporate
telstra.corp
YES –(as provided by
Suretek)
Optus
internet
Vodafone
vfinternet.au
If using public Telstra
sim enter : telstra.wap
then

APN (Access Point
Name) USERNAME
and PASSWORD is
providedby your
service provider
IPAddress or Domain
Name of CMS main
server and backup
server
IPAddress or Domain
Name of CMS remote
maintenance
SMTP server if panel has to send email e.g.
mail.bigpond.com
GPRS PARAMETERS
These values should never be
changed without Technical
Support Approval