Videofied XT GPRS User manual

Monitored GPRS Cellular alarm system
Made by RSI VIDEO TECHNOLOGIES
Installation
Manual
Security System Videofied®- Model XT GPRS
XT GPRS -
XT600i GPRS for USA/Canada,
XT700i GPRS for Australia/New Zealand
200 i GPRS for Europe and rest of the world.
Video Alarm Technologies HELPLINE: 1300 46 44 55
[email protected]
Australasian Hotline +61 (0) 7 5

Video Alarm Technologies
SETUP MANUAL
FOR
XT710 GPRS PANEL
*THIS SYSTEM REQUIRES A CMA01 FOR PROGRAMMING*
1. XT Installation
Open the Control Panel
Unscrew the 2 screws holding
the panel together
infor
[email protected]
www.videofied.com.au

2009/06/15 Ed1.0 User manual for XT710GPRS
2 | Page
*The SIM card must not be inserted or removed while the panel is powered*
Install the SIM card
Put the SIM card on the plastic
(Take care to respect the right direction)
Slide it into the connector.
*How to Mount the Control Panel
Fix the back casing on the wall
with 3 screws (n top).
*Mounting does not have to be performed
in-order to program the panel.
Power the XT panel
Option 1: Option 2:
4 x LSH20 Lithium D-Cell
Used for Standalone or Xtender mode without
Programmable Inputs. (inputs may be used if N/O)
4 x E95 Alkaline D-Cell + 12DC power supply
Used for Standalone or Xtender mode where
Programmable Inputs/Mapping will be used
n
o
p

2009/06/15 Ed1.0 User manual for XT710GPRS
3 | Page
2. XT Programming
CMA Programming Device/Keypad
or
Reset the XT Panel :
Press and hold programming button (n) for 10sec until the
Indicator LED blinks twice
Press and instantly release the programming button (n).
The indicator LED will blink once. The panel is now in ‘Learn
Mode’ for the CMA701 keypad.
CLR & ESC/NO
≤======XX======>
Insert all three batteries into the CMA701 and press on both
the ESC/NO and CLR keys at the same time and release.
The indicator LED on the keypad will blink rapidly.
©YES
KEYPAD 1
RECORDED
RSI (c)2005
www.RsiAlarm.com
<- LANGUAGE : ->
ENGLISH
Õor Öfor language selection
©YES to apply
Other languages are available by scrolling with arrows.
ITALIANO, NEDERLANDS, DEUTSCH, CASTELLANO,
SVENSKA, PORTUGUES, FRANCAIS
Press YES for the selected one.
n
n

2009/06/15 Ed1.0 User manual for XT710GPRS
4 | Page
ENTER THE
INSTALLER CODE
4 TO 6 DIGITS
THEN YES
INSTALLER CODE:
INSTALLER CODE:
xxxx
©YES
CONFIRM CODE
RE-ENTER CODE
CONFIRM CODE
xxxx
CODE NAME :
ACCESS 1
ENTRY COMPLETE
RADIO RANGE
TEST ?
RF TEST
x/9
©YES
ESC/NO
ADJUSTING
TIME AND DATE
DATE (Year) :
09/ /
DATE (Year) :
10/ /
DATE (Month) :
10/01/
The Radio Range test must be run during the learn in
process in order to ensure proper pairing with the control
panel. This test is the strength of communication between
the device and the control panel. The keypad will display a
real time range out of 9 for the device that the test is
running for. To receive the most accurate results you must
run the radio range test for at least 30 seconds.
The RF level test must be 8/9 or better for reliable
transmission.
©YES
RADIO RANGE
TEST ?
©YES
©YES
Wait while the screen changes
Use the Õor Öto set the Year
You may name the installer code using the Alphanumeric
Keypad. If you leave the name blank it will default to
‘ACCESS 1’
Use the Alphaumeric Keypad to enter the Installer Code
*This code is important to keep track of. There is no back
door to the system
Wait while the screen changes

2009/06/15 Ed1.0 User manual for XT710GPRS
5 | Page
DATE (Minutes) :
10:00
DATE (Minutes) :
10:53
03/06/09 10:53
ENTRY COMPLETE
CONNECTED TO
MONITOR.STATION?
ACCOUNT NUMBER?
ACCOUNT NUMBER:
99865123
PERIODIC TEST:
24 HOURS
Other periods are available:
48 hours, 24 hours, 12 hours,1 hour, No Test
Use arrows for the selection and press ©YES to confirm.
*We suggest at least a 24 hour test
Õor Öfor period selection
and ©YES to apply
DATE (Month) :
10/11/
DATE (Day) :
09/06/01
DATE (Day) :
09/06/03
©YES
©YES
©YES
Using the arrow keys + ©YES to choose the Hour and
Minute the periodic test will happen.
TEST MINUTE:
00:00
TEST HOUR:
00:00
Use the Alphanumeric Keypad to enter in a 4-8 digit account
number provided by the Central Station
Use the Õor Öto set the Hour
Use the Õor Öto set the Minutes
©YES
TIME (HOUR) :
00:00
YOU MUST ALWAY CHOOSE ‘YES’
©YES
TIME (HOUR) :
10:00
Use the Õor Öto set the Day
Use the Õor Öto set the Month

2009/06/15 Ed1.0 User manual for XT710GPRS
6 | Page
CODE/STATE
MODIFICATION ?
ENTER YOUR
I.D.
NAME OR ADDRESS
AREAS
CONFIGURATION
AREA NAME 1:
Other values are available:
2 min, 1 min, 45 sec
Use the arrows for the selection and ©YES to confirm.
Other values are available:
2 min, 1 min, 45 sec, 30 sec, 15 sec
Use the arrows for the selection and ©YES to confirm.
Use the Alphanumeric Keypad to name the area and press
©YES. Repeat for all areas. If you want to keep the default
area names press the ESC/NO key.
CODE/STATE modification
These are the default transmitted events:
Intrusions
Panic
Periodic Test
Tamper
Supervision Fault
Device Battery Low
Panel Battery Low
If you would like any other events to be transmitted
press ©YES and use the Õor Öto toggle
between events
If you would like the default press ESC/NO
You may name the Site
Wait
TRANS. STATE
MODIFICATION
List of all
events
©YES
ESC/NO
©YES
EXIT DELAY:
45 Sec
ENTRY DELAY:
15 Sec
ARMING OPTION:
From the host ARMING OPTION:
Standalone
ARMING OPTION: You will choose between configurations
depending on how you will be arming the system.
From the host: Will make the XT a piggyback/xtender
system that arms and disarms off the latching of 9-12v on
the arming inputs.
Standalone: Will make the XT a solo system controlled by
arming and disarming using Videofied peripheral devices.
Ö
Go to Page 7 if you will
be choosing this option
Go to Page 8 to continue with
standalone programming

2009/06/15 Ed1.0 User manual for XT710GPRS
7 | Page
©YES
Ö
Ö
Ö
Ö
Ö
ARMING OPTION :
From The Host
MODE:
Slow
MODE:
Fast
Mode Slow : Used for following the arming and disarming of
the host system. This will arm each device one at a time
conserving battery life.
Mode Fast : Used to instant arm all devices while sacrificing
battery life.
ENTRY DELAY
There is no Videofied Exit Delay with the ‘From the Host’
option. Videofied will only control the Entry Delay.
Enter the value for your Entry Delay up to 255 seconds and
press ©YES.
VALUE:(0-255)
(000):
Ö
TRANSMISSION
DELAY
Value: (0-600)
(000):
ARMING
CONFIRMATION
©YES
Value: (0-5)
(0-5):
©YES
©YES
©YES
©YES
By entering a value using the keypad, up to 600 seconds,
the transmission of any event will be delayed that many
seconds.
Enter the value you would like for the Transmission Delay
and press ©YES
Arming Confirmation is the number of seconds of latched
voltage (where voltage must stayed latched after) the panel
will require before arming.
Enter the value you would like for the Arming Confirmation
and press ©YES
©YES
Using the control panel as a Xtender system will only be able to arm and disarm by latching 9-12vDC to
one of the two inputs.
Arming input 1 will control the arming and disarming of devices in areas 1 and 2. Where devices in
area 1 are subject to the Entry Delay.
Arming input 2 will control the arming and disarming of devices in areas 3 and 4. Where devices in
area 3 are subject to the Entry Delay.

2009/06/15 Ed1.0 User manual for XT710GPRS
8 | Page
©YES
Ö
Ö
Ö
Ö
Ö
GPRS
PARAMETERS ?
APN CODE
APN CODE:
xxxxx.xxxxxx.xxx
Your APN code (Access Point Name) is given to you by your
SIM card Provider. Press ©YES to enter into the parameter
and use the Keypad to complete the code. Press ©YES to
confirm your entry and the Öarrow to move to the next
parameter.
USERNAME
PASSWORD
Your USERNAME is given to you by your SIM card Provider.
Press ©YES to enter into the parameter and use the
Keypad to complete the name. Press ©YES to confirm
your entry and the Öarrow to move to the next parameter.
PASSWORD:
xxxxxxxxxxxx
USERNAME:
xxxxxxxxxxx
©YES
IP1 ADDRESS
IP1 ADDRESS:
xxx.xxx.xxx.xxx
DOMAIN NAME 1
©YES
DOMAIN NAME 1:
xxxxx.xxx.xxx
PORT 1
PORT 1:
xxx
©YES
©YES
©YES
©YES
Your PASSWORD is given to you by your SIM card Provider.
Press ©YES to enter into the parameter and use the
Keypad to complete the name. Press ©YES to confirm
your entry and the Öarrow to move to the next parameter.
Your IP1 address is given to you by your Monitoring Station.
Press ©YES to enter into the parameter and use the
Keypad to complete the address. Press ©YES to confirm
your entry and the Öarrow to move to the next parameter.
*You will use either a IP address or a Domain Name but not
both
Your Domain Name is given to you by your Monitoring Station.
Press ©YES to enter into the parameter and use the
Keypad to complete the name. Press ©YES to confirm
your entry and the Öarrow to move to the next parameter.
*You will use either a IP address or a Domain Name but not
both leave it blank if an IP has already been entered.
The Port is given to you by your Monitoring Station. By default
the panel will use 888. If you need to modify the port press
the ©YES key to enter into the parameter and the keypad
to complete the port. Press ©YES to confirm and the
Öarrow to move to the next parameter.
GPRS PARAMETERS?
The Port is given to you by your Monitoring Station. By default
the panel will use 888. If you need to modify the port press
the ©YES key to enter into the parameter and the keypad
to complete the port. Press ©YES to confirm and the
Öarrow to move to the next parameter. Continue through
IP2 and TMT IP.
Once you have entered all valid parameters press ESC/NO
to return to the main menu then ESC/NO again to move to
the next parameter.
ESC/NO
ESC/NO

2009/06/15 Ed1.0 User manual for XT710GPRS
9 | Page
3. Other XTi setup with CMA701 keypad (Standalone ONLY)
Other setup (badges/codes, arming profiles, etc…) must be set with the CMA keypad
4. GPRS error codes
GPRS LEVEL?
TEST IN PROGRESS
YES = END
GPRS LEVEL
x/5
Videofied will require a 3/5 or better for reliable transmission
of Video alarms
During the GPRS Level test the Modem will boot and
attempt to gain access to the internet to post a Level out of
5 or an error Code that will help troubleshoot why it cannot
connect. To keep the keypad awake use any keys on the
keypad except the YES, ESC/NO, and CLR keys. This test
can take up to 5 minutes. Once the level or error has
posted press YES to continue in programming.
*For explanation of GPRS errors see page 9
RECORDING
DEVICES
Each device has a unique programming button. Please
reference the Installation Sheet for the device you would like
to program.
PRESS PROGRAM
BUTTON OF DEVICE
ENTERING A NEW
DEVICE?
END OF
CONFIGURATION
CLOSE THE PANEL
©YES or ESC/NO
©YES
©YES
OPERATION
COMPLETED? ©YES
Before completing programming make sure that all tampers
are depressed by verifying that each devices indicator LED is
off