Videx IP videokit IPVK/6296 Series System manual

VIDEOKIT
IPVK/6296 SERIES
IP one way, two way videokit
66550062-EN - V6.0 - 31/10/21 We recommend
This equipment is installed by a
Competent Electrician, Security or
Communications Engineer .
Installation handbook
IPVK
IPVKCRev.0.1

66550062-EN - V6.0 - 31/10/21
- 2 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Index
System components and available versions ................................................................................................................................ 3
Art.4533 IP speaker unit module.................................................................................................................................................. 5
Art.4901 Digital codelock module.............................................................................................................................................. 10
4000 Series surface and ush mounting door station installation .......................................................................................... 14
Art.6296 3.5" touchscreen videophone for IPure system......................................................................................................... 16
Art.6296 mounting instructions................................................................................................................................................. 24
Windows setup static IP address ................................................................................................................................................. 25
VX IPWIZARD Wizard conguration software for VIDEX IP System ........................................................................................ 27
Installation diagrams ................................................................................................................................................................... 62
INSTALLATION DIAGRAMS  NOTES AND SUGGESTIONS
• All diagrams refer to all kit versions: ush or surface.
• Dashed connections refer to optional connections (“Local
bell”, “Push to exit” & “Door monitor”).
• Some diagrams show how to connect a 12Vdc electric lock:
these directions are suitable for all diagrams in this manual.
• All diagrams shown are valid for systems with surface or ush
mount door station.
• To install this equipment are required expertises in the eld
of information and networking technologies.
DECLETION OF RESPONSIBILITY
This manual has been written and revised carefully. The instruc-
tions and the descriptions which are included in it are referred
to VIDEX parts and are correct at the time of print. However, sub-
sequent VIDEX parts and manuals, can be subject to changes
without notice. VIDEX Electronics S.p.A. cannot be held respon-
sible for damages caused directly or indirectly by errors, omis-
sions or discrepancies between the VIDEX parts and the Manual.
WE RECOMMEND
This equipment is installed by a Competent Electri-
cian, Security or Communications Engineer
To download the programming software
VX IP Wizard and obtain the latest rmware
and manuals please visit the following web-
site and register
https://service.videx.it/
MORE INFORMATION ON PAG. 27 OF THIS MANUAL.

66550062-EN - V6.0 - 31/10/21
- 3 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
System components and available versions
IPVK/6296
Colour videokit.
50
43,8
135,0
160,0
45,0 22,7
15,7
143,0
120,0
45,0
INDOOR
STATION
Videophone
Art.6296
pag. 16
OUTDOOR
STATION
Camera unit
Art.4533
pag. 5
Flush
Mounting
Surface
Mounting
ACCESSORIES
Power supply
Art.HDR-15-12
Fig. 1 - IPVK/6296 components (measures in mm)
ONE WAY VERSIONS
IPVK-1/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4851: Flush mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
IPVK-1S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4881: Surface mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
TWO WAY VERSIONS
IPVK-2/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4851: Flush mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
IPVK-2S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4881: Surface mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12

66550062-EN - V6.0 - 31/10/21
- 4 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
IPVKC/6296 Colour videokit plus a codelock module.
50135,0
280,0
45,0 22,7
263,0
INDOOR
STATION
Videophone
Art.6296
pag. 16
ACCESSORIES
Power supply
Art.HDR-15-12
OUTDOOR
STATION
Camera unit
Art.4533
pag. 5
Codelock
module
Art.4901
pag. 10
Flush
Mounting
Surface
Mounting
Fig. 2 - IPVKC/6296 components (measures in mm)
ONE WAY VERSIONS
IPVKC-1/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4901: Codelock module
1 Art.4852: Flush mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
IPVKC-1S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4901: Codelock module
1 Art.4882: Surface mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
TWO WAY VERSIONS
IPVKC-2/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4901: Codelock module
1 Art.4852: Flush mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
IPVKC-2S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4901: Codelock module
1 Art.4882: Surface mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
System components and available versions

66550062-EN - V6.0 - 31/10/21
- 5 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
D
C
E
A
BB
Fig. 1 Front
STEEL
ALI
HIGH BRASS
MATTE
4533-0
4533-1
4533-2
Made in Italy
RELAY 1 RELAY 2 INPUTS
EXT CAMERA
POWER ETHERNET
EXPANSION
BUTTONS
RS485
C1 NO1 NC1 NO2 NC2 C2 IN1
GNDI
IN2 GND +12V RX+ RX– TX+ TX–
GND
B
A
V
JP1
GND
SL
Close
Open
PROG.
4533X-0
4533X-1
4533X-2
EIA/TIA-568A
or EIA/TIA-568B
See CONNECTION table
O
F G
I
N
M
L
H
Fig. 2 Back
DESCRIPTION
Speaker unit module for IP systemwith built-in wide colour camera
with autoiris lens and white light illumination LEDs. Depending on
the speaker unit version it includes zero, one or two call push buttons.
Art. 4533X versions are also equiped with a built-in proximity
key reader and programming modes.
The unit circuitry incorporates:
• The transmitting amplier with microphone and volume control;
• The receiving amplier with volume control;
• Two enslavement relay to enable electric lock and an additional ser-
vice (3 contacts each: common, normally open and normally closed).
• The call buttons from 0 to a maximum of 2 depending on the
module version;
• The illumination LEDs for the card name holder;
• The camera comprised of illumination LEDs.
To download the programming software
VX IP Wizard and obtain the latest rmware
and manuals please visit the following web-
site and register
https://service.videx.it/
LEGEND
ACamera with illumination LEDs
BOperation LEDs
CLoudspeaker
DCard name holder with built in-in proximity key reader
(only Art.4533X versions)
ECall push button (0, 1 or 2 depending on the model)
FLoudspeaker volume
GMicrophone volume control
HRS485 connection terminals
IBoot loader push button for rmware update
LRS485 termination jumper
MExternal camera connection terminals
NButton expansion modules connector
OSystem connection terminals
AVAILABLE VERSIONS
Art.4533-0 Art.4533X-0 Art.4533-1
Art.4533X-1
Art.4533-2
Art.4533X-2
LEDS
Flashes when the called indoor station is busy.
The LED will be o when the system is in stand-by.
If illuminated, indicates that the call from the outdoor sta-
tion is in progress. The LED will switch OFF when the call
is answered or expired the call time without any answer.
If illuminated, indicates that it is possible to speak because
the call has been answered. The LED will switch OFF at the
end of a conversation (or at the end of the conversation time).
If illuminated, indicates that the door lock has been op-
erated. It will switch OFF at the end of the programmed
“door opening” time.
CONTROLS
Microphone volume
Adjust the microphone volume.
Rotate clockwise to increase or anti-clockwise to decrease
Loudspeaker volume
Adjust the loudspeaker volume.
Rotate clockwise to decrease or anti-clockwise to increase
Rev.0.1
Art.4533X Speaker unit with built-in camera & proximity key readeri
Art.4533 Speaker unit with built-in camera

66550062-EN - V6.0 - 31/10/21
- 6 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 Speaker unit with built-in camera
Art.4533X Speaker unit with built-in camera & proximity key reader
PROGRAMMING
The programming of the module is carried out through the VIDEX IP Wizard software. There are some adjustments available directly
on the module:
• Microphone volume through the relevant trimmer;
• Speaker volume through the relevant trimmer;
• RS-485 connection termination.
For the module programming refer to the section VIDEX IP Wizard.
CONNECTION
EIA/TIA568A
1
2
3
4
5
6
7
8
EIA/TIA-568A
TX+
TX−
RX+
RX−
4533 signals RJ-45 pin
TX+ PIN 1 - White-green
TX–PIN 2 - Green
RX+ PIN 3 - White-orange
RX–PIN 6 - Orange
EIA/TIA568B
1
2
3
4
5
6
7
8
EIA/TIA-568B
TX+
TX−
RX+
RX−
4533 signals RJ-45 pin
TX+ PIN 1 - White-orange
TX–PIN 2- Orange
RX+ PIN 3 - White-green
RX–PIN 6 - Green
OTHER STANDARD CABLES
1
2
3
4
5
6
7
8
TX+
TX−
RX+
RX−
4533 signals RJ-45 pin
TX+ PIN 1 Twisted pair
TX–PIN 2
RX+ PIN 3 Twisted pair
RX–PIN 6
J2 AND J1 JUMPERS BACKLIT LEDS SETTINGS
For proper functioning please set J2 and J1 jumpers of any con-
nected button expansion module Art.404X as shown in the ta-
ble aside.
J2 J1
B A B A
OPERATION
The system operation is supported by the built-in LED.
• When a visitor press a call button the units emits an intermittent deep call tone and in correspondence with the tone the red
LED ashes (Fig. 3) until the resident answer or the programmed call time expires.
• If the called indoor station is busy the red LED ashes (Fig. 4) 4 times quickly and the unit emits a deep tone on each ash.
• When the resident answers, the yellow LED (Fig. 5) illuminates and remains illuminated until the conversation terminates.
• If the resident open the door, the green illuminates (Fig. 6) for the programmed door opening time.
ERROR MESSAGES
The LED is used also to provide error messages concerning system misfunctions:
• A fast ashing LED shows connection to the push notication service is being made. This should only be temporary; if this persists then
there is something not working correctly;
• Slow ashing means that the gateway set cannot be reached;
• xed on means that the SIP server cannot be reached or connection not allowed because of wrong credentials.
Fig. 3 Call in progress Fig. 4 Calling a busy indoor
station
Fig. 5 The conversation is in
progress
Fig. 6 Door opening

66550062-EN - V6.0 - 31/10/21
- 7 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 Speaker unit with built-in camera
Art.4533X Speaker unit with built-in camera & proximity key reader
PROGRAMMING TAGS ONLY ART.4533X VERSIONS
The programming of the tags is carried out through the VIDEX IP Wizard software.
USING TAGS
Place a tag in front of the tag reader:
↪If the tag is programmed, the external module emits two high-pitched “beeping” sounds and its relay is activated.
BIP BIP
↪If the tag is not programmed, the external module emits three low-pitched “beeping” sounds and its relay is not
activated.
BIP BIP BIP
FACTORY DEFAULT PROCEDURE FOR ENTRANCE PANEL SUPPLIED WITH VIDEOKITS
The following procedure can be used to reset and pair the videophone and entrance panel supplied in a one apartment or two
apartment kit. Once paired the door panel will call the videophones without any further setup required. Additional setup is optional
to set device names, specic IP addresses etc. The default IP addresses are:
Entrance panel 192.168.1.180 // Videophone 1 192.168.1.181 // Videophone 2 192.168.1.182
4533 DOOR PANEL RESET FOR ONE OR TWO APARTMENT VIDEO KIT
The door panel is required to be open for this procedure.
1. Power down the door station;
2. Restore the power keeping pressed Call Button 1 (Bottom button on a 2 button panel Fig. 7) until the (red) and (green)
led’s start ashing together (Fig. 8)*;
3. Press the boot loader button once (inside the panel) (Fig. 9), the red LED will stop ashing while the green LED contin-
ues ashing together with the yellow LED (Fig. 10);
4. Press call button 1 (Fig. 11) for a one way videokit otherwise press call button 2 (Fig. 12) for a two way video kit;
5. When the button is released, the door panel emits one long beep for one way videokit or two long beeps for two way videokit
then reboots with the new settings.
* If the door panel is connected to the cloud, the LED will ash twice and the panel will reboot without changing your settings. In this case, the IP wizard must be used to make any changes
to the door panel settings.
Fig. 7 Keep pressed button 1 Fig. 8 Bell & Key LEDs ashing
STEEL
ALI
HIGH BRASS
MATTE
4533-0
4533-1
4533-2
Made in Italy
RELAY 1 RELAY 2 INPUTS
EXT CAMERA
POWER ETHERNET
EXPANSION
BUTTONS
RS485
C1 NO1 NC1 NO2 NC2 C2 IN1
GNDI
IN2 GND +12V RX+ RX– TX+ TX–
GND
B
A
V
JP1
GND
SL
Close
Open
PROG.
4533X-0
4533X-1
4533X-2
Fig. 9 Press the boot loader button (back
of the module)
Fig. 10 Speech & Key LEDs ashing Fig. 11 One way videokit Fig. 12 Two way videokit

66550062-EN - V6.0 - 31/10/21
- 8 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
ENABLE BOOTLOADER MODE
In case of rmware update failure (i.e. because of mains failure or cable disconnec-
tion during the update etc.) and the door panel is no longer recognised by theVidex
IP Wizard software, you can try to restore it by manually putting it into boot mode.
It is strongly recommended that this operation is carried out by a qualied engineer
and in any case after a contact with Videx support.
• Disconnect the door panel from the power supply.
• Press and keep pressed the
I
button (Fig. 2 on page 5) then connect again
the power supply source.
• The door panel will go into boot mode which is indicated by the four LED’s
ashing alternatively (Fig. 13).
• Now proceed using the utility “VidexFirmwareUpdater.exe” to upload the
rmware to the device.
• If the update process terminates correctly, the device should be restored and ready to work.
• If the device still does not work, please contact the supplier to proceed according to the warranty terms.
CAMERA NOTES
MAXIMUM ILLUMINATION DISTANCE
FROM CAMERA AT NIGHT
The illumination LED’s within the camera
will illuminate the visitor when they are
within 50cm of the camera.
MAX 50 cm
FIELDS OFVIEW
The elds of view for standard camera are 55° for vertical angle and 115° for horizontal angle
while for Wide Angle camera are 80° for vertical angle and 170° for horizontal angle.
195 cm
80° 55°
170 cm
100 cm
75 cm
135 cm
70 cm
Vertical angle
170°
115°
180 cm
105 cm
70 cm
Horizontal angle
Standard camera Wide Angle camera
ADHESIVE GASKET PLACEMENT
Apply the Yseal as shown in Fig. 14.
ANTITAMPERING LOCKS FIXING
Fit the anti-tampering locks Was shown in Fig. 15.
Y
G
Fig. 14
W
Fig. 15
HOW TO REMOVE/INSERT THE CARD NAME HOLDER
• To avoid damage to the module front plate, mask the side that
will be in contact with the screwdriver blade;
• Insert the screwdriver (at side) into the card-holder hole as
shown in Fig. 16;
• Move the screwdriver to the left as shown in Fig. 17 to extract
the card name holder;
• Edit the card name then replace it inside the holder and ret:
insert the holder inside its housing from the left or right side
then push the other side until it clips into place. Fig. 16 Fig. 17
Fig. 13 Door panel in BOOTLOADER mode
Art.4533 Speaker unit with built-in camera
Art.4533X Speaker unit with built-in camera & proximity key reader

66550062-EN - V6.0 - 31/10/21
- 9 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 Speaker unit with built-in camera
Art.4533X Speaker unit with built-in camera & proximity key reader
CONNECTION TERMINAL SIGNALS
EXT
CAMERA
SL Active low output enabled when the
external video input is in use
GND Composite video signal ground reference
VComposite video signal input
RS485
ARS-485 Connection
(termination adjusted through the JP1 jumper)
B
GND
POWER +12V 12Vdc - 400mA power supply input
GND
INPUTS
IN1 Active low input 1 (when enabled activate
the programmed output)
IN2 Active low input 2 (when enabled activate
the programmed output)
GNDI Ground for IN1 and IN2 inputs
ETHERNET
RX– Ethernet Connection Orange (568A)
RX+ Ethernet Connection White/Orange (568A)
TX– Ethernet Connection Green (568A)
TX+ Ethernet Connection White/Green (568A)
RELAY 2
C2 Relay 2 common contact
Max
12-24
Vac/dc
0.4A
NC2 Relay 2 normally closed contact
NO2 Relay 2 normally open contact
RELAY 1
C1 Relay 1 common contact
NC1 Relay 1 normally closed contact
NO1 Relay 1 normally open contact
TECHNICAL SPECIFICATION
Video codec: H.263
H.263+
Supported resolutions:
352x288 (CIF) used in SIP standard mode
320x240 used betweenVidex devices and app
176x144 (QCIF) used in SIP standard mode
Audio codec: G.711 μ-law, A-law
Sampling frequency: 8 khz
SIP compatibility: SIP 2.0
Power Supply: 12Vdc - 400mA
Power consumption: Stand by: 250mA
Operating: 380mA
Working Temperature: -10 +50 °C
CLEANING OF THE PLATE
Use a clean and soft cloth. Use moderate warm water or non-ag-
gressive cleansers.
Do not use:
• abrasive liquids;
• chlorine-based liquids;
• metal cleaning products.

66550062-EN - V6.0 - 31/10/21
- 10 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
A B
C
Fig. 1 Front
MOV
NO1 NC1 NO2 NC2 NO3 NC3
SW2
SW1
NC2
NO2 C2
NC3
NO3 C3
NC1
C1
– +
NO1
Made in Italy
4901
STEEL
ALI
HIGH BRASS
MATTE
Note: Remove MOV
jumper completely
when using a relay to
trigger a gate controller.
A
BJPL ED
F
Fig. 2 Back
DESCRIPTION
The Art.4901 is manufactured from 316 grade brushed stainless
steel and the module features 12 stainless steel buttons, backlit
in blue (Keys 0 - 9, ENTER and CLEAR) and 2 LED’s for progress
information during use and programming. With three integral
relays each with common, normally open and normally closed connections and two inputs to enable the external triggering of
relays one and two (for example, push to exit button). Key presses are signalled both acoustically and visually while each button
press has a tactile feel. Entering the correct code followed by ENTER will activate the relevant relay. Programming is carried out
through the same keypad following a simple programming menu. The module can be combined with other 4000 Series modules in
an audio or video intercom system.
LEGEND
AGreen LED
BRed LED
CBacklit keypad
DJPL jumper
EMOV jumpers
FConnection terminals
MAIN FEATURES
• 3 C, NC, NO relay outputs (24Vac/dc – 5A max);
• 3 Programmable secret codes (one for each relay);
• Each relay can be set to be activated for a specic time (01 to 99 seconds) or to work as latch;
• Two active low inputs to command directly the relay 1 and 2;
• Programming menu guarded by a 4-8 digit programmable engineer’s code;
• Visual and Acoustic signal during operating and programming;
• Keypad illumination LEDs;
GENERAL DIRECTIONS FOR INSTALLATION
In order to achieve the best results from the schematics described it is necessary to install only original VIDEX equipment, strictly
keeping to the items indicated on each schematic and follow these General Directions for Installation:
• The system must be installed according to national rules in force, in any case the running of cables of any intercom unit must be
carried out separately from the mains;
• All multipair cables should be compliant to CW1308 specication (0.5mm twisted pair telephone cable).
• Cables for speech line and service should have a max resistance of 10 Ohm
• Lock release wires should be doubled up (Lock release wires and power supply wires should have a max resistance of 3 Ohm);
• The cable sizes above can be used for distances up to 50m. On distances above 50m the cable sizes should be increased to keep
the overall resistance of the cable below the RESISTANCES indicated above;
• Double check the connections before power up;
• Power up the system then check all functions.
Art.4901Digital codelock module Rev.0.1