Videx DINPAD User manual
1DINPAD
DINPAD
9mm
80mm
80mm
Technical CharacterisƟĐƐ
OperaƟŶŐsoltĂŐe: ϭϮͲϮϰsDCϭϱͲϮϰsAC
Current cŽŶƐƵŵƉƟŽŶ Standby 30mA; Max 100mA
Relays: ϯΛϮϰsDCϮϯϬsAC
RelaLJƟŵĞ 1 - 99 Seconds or latĐŚŝŶŐ;ϬϬͿ
Codes: 99 User cŽĚĞƐ;ϭͲϴĚŝŐŝƚƐͿ
IP raƟŶŐ IP40
,ŽƵƐŝŶŐ ABS
MounƟŶŐ UK electricĂůŇƵƐŚďĂĐŬ;ƐŝŶŐůĞŐĂŶŐͿ
tŝƌŝŶŐ TĞƌŵŝŶĂůďůŽĐŬ
OperaƟŶŐƚemperature: -25°C to +50°C
Note: Wall mount box not supplied!
MounƟŶŐ
DINPADC DINPADS DINPADW
These low profile standalone keypads are designed to fit
a standard UK single-gang electrical back box and are
available in 3 different colours: charcoal, silver and white.
They incorporate an easy to follow programming menu
allowing up to 99 unique codes and setting up of relay
output times.
The keypad also includes an input to trigger the relay
from a push to exit button (configured as push-to-make).
User Manual
+
+
0;!%
0;!%
<9
0!(
02
!!,#%-
9
)%9%
)%
)%9%#
'
9
9
)%9%
)%
)%9%#
'
9
'#=!
259+>>=!
6
(18.9%
?!
4!25#)
<@A
)%"!,!!-
)#@A
)%"!,!!-
ŵďĞƌ@A
3%#'!
)#4'#
0259+>>
25 )
@A!
#25;% 25B!5%
!"
#
ŵďĞƌ!"
#
ŵďĞƌ!"
!$$%%%
!$&'()*
+,$"-
+$ŵďĞƌ!
/$#4##4!4'#4C
(18.9%
!
"
# $%&&
'&&(!
# %) !
" *#"
"
!# $%$
+ ,-+ .-+ !/-
"
" 0'((
,12'.(
# 3 $%$
# 3$%&& $%$$&
$$/(4
"
" 0'((
"'
# $%&&
"
" 0'((
"(
"
" 0'((
"''
5
6
7
!
!
'5
6
7
5
6
7
!
$PEHU+
$PEHU+ ,,
$PEHU+
$PEHU+ ,,
$PEHU+
$PEHU+
$PEHU+ ,,
$PEHU+ ,,
(18.9%
8
!$
$%&''(()&(')(*%&
C 5B!,+B+#-C
$%&'+(),,&)+-'.)/),('
C 04#C
$%&'((-,,&),('
C 5#$#4#4!C
C 5$5A'>5C
$%&',,&),('0)((-(,*
C 5%!!#!#C
C 5!($!%C
&C 54!%%;!##C
C 55;4!%C
C 5B!,+B+#-C
%)+--''(())0,*)(+)&1+())
C 5%!
(18.9%
6DINPAD
DINPAD
ENUK-VB2
Fig.1
Fig.2
Fig.3
Access Granted
Enter <user code> (1-8 digits)
Press A
1. Observe the amber LED as this will flash with
each button press and the DINPAD will emit a
single beep for each press (Fig.1).
2. The amber LED will flash twice and the
DINPAD will emit a double beep (Fig.2).
3. The relevant relay will activate and the green
LED will switch ON for the duration of the
relay time (Fig.3).
User Operation
Access Denied
1. When an incorrect <user code> is entered the amber LED will continuously flash
for approximately 5 seconds and no relay will operate.
Latching Mode
1. When the relay has been setup in latching mode (relay time set for 00), enter the
<user code> then press A to latch the relay.
2. The amber LED will flash with each button press (Fig.1) as the <user code> is
entered and will emit a single beep with each press.
3. Once the A button has been pressed the amber LED will flash twice and the
keypad will emit a double beep (Fig.2).
4. The relevant relay will activate and the green LED will switch ON and stay ON
until the relay is unlatched.
5. To unlatch the relay enter the <user code> then press A, the green LED will
switch OFF and the relay will reset.
(18.9%
2()3..+,
#("!%@#
.D#A
9;.%
9AEFF
D&
>(ED
()3..+,
%
%05
%6%
@#
A
>(&
,3+,&&()
*B#(ƵŬC
&D
>(&
;;;CB#(ƵŬC
(18.9%
This manual suits for next models
3
Table of contents
Other Videx Keypad manuals
