Viega Domoplex 6928 User manual

Model Year built:
6928 from 06/2015
en_INT
Domoplex drain equipment
Instructions for Use

Domoplex drain equipment 2 from 15

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 7
2.2.1 Overview 7
2.2.2 Technical data 7
3Handling 9
3.1 Assembly information 9
3.1.1 Mounting conditions 9
3.1.2 Installation dimensions 9
3.2 Assembly 9
3.2.1 Mounting the drain 9
3.2.2 Connecting the wastewater system 11
3.2.3 Leakage test 12
3.3 Maintenance 12
3.4 Cleaning the drain 12
3.5 Disposal 15
Table of contents
Domoplex drain equipment 3 from 15

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at www.viega.com/legal-notices.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nheating and sanitary professionals and trained personnel
noperators
nconsumers
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general approved rules of engineering and the Viega instructions for
use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
About these instructions for use
Domoplex drain equipment 4 from 15

Notes give you additional helpful tips.
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand-
ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.
About these instructions for use
Domoplex drain equipment 5 from 15

2 Product information
2.1 Intended use
2.1.1 Areas of use
NOTICE!
Risk of damage due to unsuitable liquids.
To avoid damaging the drain, only introduce the following
liquids:
– Liquids with a pH-value higher than 4
– typical household water with a maximum temperature of
95 °C
The Domoplex shower drain is a drain with odour trap for shower trays
with 52 mm drain holes.
Detailed information regarding all shower tray models and the corre-
sponding Viega drains can be found in the catalogue or on the Internet.
Product information
Domoplex drain equipment 6 from 15

2.2 Product description
2.2.1 Overview
1
2
3
4
567 98
Fig. 1: Components
1 - cover plate
2 - immersion pipe
3 - fixing flange with screws
4 - seal
5 - odour trap
6 - sealing ring
7 - sliding ring
8 - union nut
9 - drain elbow
2.2.2 Technical data
Drainage capacity at an accumulation height of
120 mm
0.73 l/s
Diameter drain hole 52 mm
DN (nominal diameter) drain support 40 / 50 mm
Height 80 mm
Dimensions and installation depth
ÄChapter 3.1.2 „Installation dimensions“ on page 9
Water head seal 50 mm
Product information
Domoplex drain equipment 7 from 15

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
The following requirements exist for the mounting of the drain:
nThe shower tray is installed.
nThe drainage line is installed all the way to the shower tray.
nThe underside of the shower tray is accessible.
nThe drainage capacity is sufficient at an accumulation height of
120 mm.
3.1.2 Installation dimensions
75Ø
70 Ø
Fig. 2: Dimensional drawing
3.2 Assembly
3.2.1 Mounting the drain
Proceed as follows to mount the drain:
Place the seal on the sealing surface of the drain and push into the
holding groove.
Insert seal
Handling
Domoplex drain equipment 8 from 15

Position the drain unit with seal under the shower tray.
Push the upper part of the seal through the drain hole.
Place fixing flange and insert the screws by hand.
NOTICE! Only use a screwdriver, not a cordless screwdriver.
Tighten screws evenly.
Insert immersion pipe into the odour trap.
Secure drain
Handling
Domoplex drain equipment 9 from 15

Press the cover plate onto the two fixing points.
3.2.2 Connecting the wastewater system
Proceed as follows to connect the drain to the waste water system:
Requirement:
nThe drain unit is installed onto the shower tray.
If the waste water pipe only has a diameter of 40 mm, cut off drain
elbow.
Push the union nut, sliding ring and seal onto the drain pipe.
Screw the union nut onto the drain unit.
DN 40
DN 50
Handling
Domoplex drain equipment 10 from 15

Align the odour trap in such a way that the drain elbow can be con-
nected to the waste water pipe.
Push waste water pipe onto the drain elbow.
3.2.3 Leakage test
The leakage test is only carried out as a visual inspection.
Check drain fitting for visible leaks.
3.3 Maintenance
NOTICE!
Risk of damage due to unsuitable cleaning agent.
The following cleaning agents can damage chrome-plated
surfaces and therefore may not be used:
– scouring agent
– abrasive sponges
– lime, plaster or cement dissolver
– solvents or other acidic cleaning agents
Normal soap or a mild cleaning agent can be used for regular care and
prevention of lime scale on the rotatable rosette and valve cone. Under
no circumstances should scouring agent or scratching objects be used.
Strong stains, even around the drain unit and the siphon, can be
removed using typical household cleaner. It should be noted that the
cleaning agent should be rinsed off after the prescribed soaking time.
There should be no residue on the components.
3.4 Cleaning the drain
NOTICE!
Be careful not to damage the odour trap when cleaning the
drain system.
Handling
Domoplex drain equipment 11 from 15

Remove cover plate.
Remove the immersion pipe upwards.
For free access to the drain pipe:
Grip the closing plug on the lug with pliers and pull off.
Clean the drain carefully to avoid damaging the fitting.
Handling
Domoplex drain equipment 12 from 15

Insert closing plug flush with the surface.
Make sure to position the closing plug properly. The lug must be
positioned vertically.
Insert immersion pipe.
Mount cover plate.
Handling
Domoplex drain equipment 13 from 15

3.5 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Domoplex drain equipment 14 from 15