Viking VCRT300 User manual

Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA

IMPORTANT: PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely
and carefully.
• Do not remove permanently affixed labels, warnings, or
plates from product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• Please ensure that this product is properly grounded.
•The installer should leave these instructions with the
consumer who should retain for local inspector's use and
for future reference.
Installationmust conform with localcodes or inthe absence of
codes, with the National ElectricalCode, ANSI/NFPA 70-latest
edition. InCANADA: Electricalinstallationmust be in
accordancewith the currentCSA C22.2 CanadianElectrical
Codes Part1 and/or local codes.
GENERAL INFORMATION
•WARNING: The useof cabinets for storage above
the appliance may result in potential fire or burn hazard.
Combustible items may ignite, metallic items may
become hot and cause burns. If a cabinet storage is to
be provided the risk can be reduced by installing a
rangehood that projects horizontally a minimum of 5"
(12.7 cm) beyond the bottom of the cabinets.
•WARNING: This appliance shall not be used for
space heating. This information is based on safety
considerations.
• All openings in the wall behind the appliance and in the
floor under the appliance shall be sealed.
• Keep appliance area clear and free from combustible
materials, gasoline, and other flammable vapors.
• Disconnect the electric supply to the appliance before
servicing.
• When removing oven for service and/or cleaning,
disconnect AC power supply.
• Electrical requirements:
Listed in specifications chart. Electrical installation
should comply with national and local codes.
ELECTRICAL GROUNDING
INSTRUCTIONS
This rangetop must be electrically grounded in
accordance with local codes or, in the absence of
codes, with the National Electrical Code,
ANBI/NFPA 70-latest edition..
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
ELECTRICAL REQUIREMENTS
Check your national and local codes regarding this
unit. This rangetop is supplied with a 3 wire
240/208, 60hz conduit which is equipped with a No.
10 ground wire. Bee electrical connection section for
grounding instructions. This unit should be fused
separately. CAUTION: Be sure the electrical power
is off from the breaker box to the junction box until
the unit is installed and ready to operate. The
junction box should be connected to a suitable
ground.
ELECTRICAL CONNECTION
WARNING: The electrical power to the unit
must be shut off while line connections are being
made. Failure to do so could result in serious
injury or death.
When making the wire connections, use the entire
length of the conduit provided (3 feet). The conduit
must not be cut. Connect the red and black leads
from the unit conduit to the corresponding leads in
the junction box. The bare ground wire in the conduit
is connected to the unit frame. When connecting to a
3-conductor branch circuit, if local codes permit,
connect the bare ground connector lead of the unit to
the branch circuit neutral (gray or white in color).
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE. SUCH USE MAY RESULT IN A FIRE,
ELECTRICAL SHOCK OR OTHER PERSONAL INJURY.
BACK TRIM ACCESSORIES
Assembly and installation instructions are included
with all back trim accessories.

SPECIFICATIONS-ELECTRIC RANGETOP
Description
Overall Width
Overall Height from
Bottom
VCRT300
BASE HEIGHT
To top of glass frame
7 7/8" (20.0 cm)
Overall Depth from To edge of side panel -
Rear To end of control panel -
To end of knobs -
Cutout Width
Cutout Height
Cutout Depth
VI RT300
29 7/8" (75.9 cm)
ADDITIONS TO BASE HEIGHT
add 1 1/4" (3.2 cm)
add 6" (15.2 cm)
add 23 1/2" (59.7 em)
To top of island trim -
To top of backguard -
To top of high-shelf -
24" (61.0 cm)
25 15/16" (65.9 em)
27 7/16" (69.7 cm)
30" (76.2 cm)
7 1/2" (19.1 cm)
24" (61.0 cm)
Electrical 3-Wire, 240/208 VAC, 60 Hz, electrical connection.
Requirements Unit is equipped with No. 10 ground wire in conduit. Should be fused separately.
Maximum Amps 240v- 37.9 amps
208v- 32.8 amps240V 208V
Left Front 2500 watts 1875 watts
Left Rear 1500 watts 1125 watts
Right Front 1200 watts 900 watts
Right Rear 3300 watts 2475 watts
240v - 40.0 amps
208v - 34.6 amps
240V 208V
Left Front 2700 watts 2025 watts
Left Rear 1800 watts 1350 watts
Right Front 1200 watts 900 watts
Right Rear 3300 watts 2475 watts
Surface Element
Rating
Approximate 110 Ibs. (49.5 kg)
Shipping Weight
Minimum clearances from adjacent combustible construction
• Cooking surfaces and below (36"[91.4 cm] and below)
• Sides- 0"
• Rear- 0" with backguard or highshelf; 0" with island trim and non-combustible wall;
6" (15.2 cm) with island trim and combustible rear wall
•Top grate support - 36" (91.4 cm)
•Above cooking surface (above 36"[91.4 cm])
• Sides- 6" (15.2 cm)
•Within 6" (15.2 cm) side clearance, wall cabinets no deeper than 13" (33.0 cm) must be minimum 18" (45.7 cm)
above cooking surface.
•Wall cabinets directly above product must be minimum 36" (91.4 cm) above cooking surface

PROXIMITY TO CABINET INSTALLATION
1. This rangetop may be installed directly adjacent to existing 36" (91.4 cm) high base cabinets.
2. The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36" (91.4 cm) high. There must be a minimum of 6" (15.2 cm) side clearance from the rangetop to
such combustible surfaces above the 36" (91.4 cm) counter height.
3. Within the 6" (15.2 cm) side clearance to combustible vertical surfaces above 36" (91.4 cm), the maximum wall
cabinet depth must be 13" (33.0 cm) and wall cabinets within this 6" (15.2 cm) side clearance must be 18" (45.7 cm)
above the 36" (91.4 cm) high countertop.
4. Wall cabinets above the rangetop must be a minimum of 36" (91.4 cm) above the rangetop cooking surface for the
full width of the rangetop.
SIDE FRONT
71/2"
(19.1 cm)
t
36" Min.
(91.4 cm)
,t
13" Max
(33.0cm)
Im"lk "& "k "ll_'lL_k "& "1_"k III
-1
t
36" Min.
I_1"1 (91.4 cm) OC]
A6" Min._
('15.2 cm_
DD
18" Min.
(45.7 cm)
t

INTERIOR CABINET CLEARANCES FOR PROPER AIR FLOW
DETAILED VIEW OF
BOTTOM SUPPORT
E) DD
J
\\
f
mj
DD
23/4"
"_'1 I_(7'0 cm)
1 1/2" dia.
cutout for
conduit
r3,, (7.6 cm)
t 8,,t
(20.3 cm)
2"
_(5.1 cm) t
t t
8" (20.3 cm)
t t
1/2"
(3.8 cm) L;,, (7.6 cm)
Remove the material from this area
for proper air flow into the unit.
IMPORTANT: The electronic components for the induction
elements in the rangetop need some air circulation. To ensure
long life of electronic components, it is required that a minimum of
8" (20.3 cm) of open space remain between the bottom of the unit
and any shelf underneath. The maximum length of the shelf
underneath is to be 18" (45.7 cm) There should be no partition or
shelf directly underneath the unit. 8" Min.
(20.3 cm)
I 18" Max.
(45.7 cm)

FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. All stainless steel body
parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If build-up
occurs, do not use steel wool, abrasive cloths, cleaners, or powders!! If it is necessary to scrape stainless steel to
remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper.
Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel! Scratches are almost
impossible to remove.
2. The interior of the oven should be washed thoroughly with hot, soapy water to remove film residues and any
installation dust or debris before being used for food preparation, then rinsed and wiped dry. Solutions stronger
than soap and water are rarely needed.
REPLACEM ENT PARTS
Only authorized replacement parts may be used in performing service on the range. Do not repair or replace any
part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a
qualified technician.
WIRING DIAGRAM
ELECTRIC ALL INDUCTION RANGETOP
LEFT
TEM_CO_TROL
TEM_CONTROL
_l
L2
_ED
WARNING:
CAUTION:
T_M_CONTROL
T_M_CONTROL
R_HT
This unit must be properly grounded. See Installation Instructions for proper grounding
instructions. NOTE: Trailers or stripes will be the second color in a color combination.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing.

WIRING DIAGRAM
ELECTRIC INDUCTION/RADIENT RANGETOP
_ED/SLK
_YELIRED
I REO_BLK
"_EL/RED
WH/RED
_E
vlo
_Row
-_R
_RE_
,REDIBLK
--J16
_J17
_J7
_J4
_J5
J12_
J13_
J2
÷118 JOUT3_
_J19 JOUT4_
JOUTI-
JOUT2t
J3 rEMPCONTROL
J14_J15_
J8 m _LAC
JI0 --_L
[EMPCONTROL
_E_
_qH_SLK
¥EL/SLK -WH/BLK ¥EL_SLK
L_
BLACK REO
L _E_
_URPLE_E[_
SURFELEM
POWER ON
LIGHT
_ED--
WARNING: This unit must be properly grounded. See Installation Instructions for proper grounding
instructions. NOTE: Trailers or stripes will be the second color in a color combination.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing.

F20115 (PSO506VR)