Viking E-1600-30-IP User manual

E-1600-30-IP or
E-1600-30-IPEWP
VoIP Emergency Phone
February 11, 2021
1.0 Out-of-Box
QUICK START GUIDE
VIKING Electronics, Inc.
KSee Product Manual for complete installation and programming instructions.
1.3 Download and install the programming software
1. Go to www.vikingelectronics.com and enter E-1600-30-IP in the search box
2. Click E-1600-30-IP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on
setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
2.0 Power Source
Select PoE Switch or PoE Injector that meets the following requirements:
1. IEEE 802.3af / 802.3at / 802.3bt compliant
2. Capable of providing at least 4 Watts (class 1)
Note: CAT5e (or higher) cable recommended
1. 1 Verify that you have received all of the parts listed
1.2 Download the product manual
1. Go to www.vikingelectronics.com and
enter E-1600-30-IP in the search box
2. Click E-1600-30-IP in the search results
3. Click Product Manual to open and
download the PDF
X 1 E-1600-30-IP or E-1600-30-
IPEWP Emergency Phone
X 1 Torx T-10 Security Bit
X 4 6-32 x 3/4” Flat Head Torx
Drive Screws
X 3 Gel-Filled Butt Connectors
X 1 Faceplate Gasket
X 1 Label Braille
X 1 Flush Mount Back Box
X 1 Wire Nut
Scan the QR code to
open and download
the product manual - OR -

4.0 Features Overview
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
E-1600-30-IP Quick Start Guide ZF303603 REV B
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full-duplex
• If Spanning Tree Protocol (STP) is enabled, enable Portfast and BDPU Guard Globally
3.0 Network Port Settings
Rear (PCB) View of E-1600-IP Series
Emergency Phone
Connect to Optional
Strobe Light, LV-1K, etc.
Viking model SL-2
shown (not included),
see DOD 242
|
OR
|
MAC:
18E80FXXXXXX
asdesaxtff
N.C. (Gray)
N.O. (Yellow)
COM. (Blue)
Optional 2 Amp Relay
Output Contacts
(2A@30VDC / 250VAC max)
3 Gel-Filled Butt
Connectors (included)
- Black
+ Red
Black
Black
- Black
+ Red
LED
Help Switch
Info Switch (optional)
Speaker
Microphone
MAC Address Label: The MAC
address is a unique 12 digit number
used by routers to send network traffic
to the correct IP address.
PoE LAN Port 10/100, PoE Class 1
(<4 Watts): Connect to your LAN via
RJ45 plug and CAT5 or greater
twisted pair wire.
Yellow Network Status LED: Lights
steady to indicate power and data
link. Blinks to indicate network activity.
Green Unit Status LED
Red
Red
Yellow
Yellow
Viking model LV-1K
shown (not included),
see DOD 246
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a
maximum insulation of 0.082 inches. Cut off stripped wire ends before terminating.