Viking K-1500-EHF Instructions for use

• Handsfree or handset models available
• Phone line powered
• No dial pads
• Designed to mount in a standard emergency
phone enclosure
• Built for easy installation and simple operation
K-1500-E Features
• Hearing aid compatible handset
K-1500-EHF Features
• Auto answer feature allows remote monitoring
(can be disabled)
•Adjustable time out to limit prank calls and false
alarms (approximately 30 seconds - 6 minutes)
• Two-way handsfree communication
• Vandal resistant metal push button
The K-1500 Emergency Telephones provide
reliable emergency communication without
complicated dialing procedures.
Simple Emergency Phones
VIKING©
Technical Practice
Telecommunication Peripheral Products K-1500-E
K-1500-EHF
Emergency/Elevator Phones
February 2, 1999
Features Applications
Power: Telephone line powered (18V DC/20mA minimum)
Dimensions: 174mm x 251mm x 63.5mm (6.8” x 9.875” x 2.1”)
Shipping Weight: K-1500-E - 1.13 kg (2.5 lbs), K-1500-EHF - .91
kg (2 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
Connections: RJ11 jack
Specifications
http://www.VikingElectronics.com
[email protected]
K-1500-E K-1500-EHF
• Commercial, industrial and residential door
security
• Door or gate communication
• Truck stop/gas station fuel island
communication
• Business delivery entrances
• Use in conjunction with a Viking Hot-Line Dialer
on C.O. lines or analog PABX/KSU stations
• Use on any programmed ringdown circuit of an
analog PABX/KSU station
The K-1500-E and K-1500-EHF can be
connected directly to a C.O. line or analog
PABX/KSU station when used in conjunction
with a Hot-Line Dialer or programmed ring
down circuit. The phones can also be used
with Viking’s DLE-200B ring down circuit.
The K-1500-E and K-1500-EHF components conform to industry-set standards, and
are mounted on a formed metal panel and finished in red powder paint.
When the button is pressed, the K-1500-EHF
will come off hook until the preselected time-out
has
has elapsed (adjustable from 30 seconds to 6 minutes). During this time, the user may
converse handsfree. Alternatively, standard handset communication is used with the
K-1500-E.

Printed in the U.S.A. ZF280240 Rev EFax Back Doc # 220
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking
Electronics, its affiliates and/or subsidiaries assume no responsibility for errors and/or omissions contained in this information. Revisions of
this document or new editions of it may be issued to incorporate such changes.
Product Support Line...[phone] Fax Back Line...[phone]
Installation/Programming
A. Wiring the K-1500-E
Rear View of the K-1500-E Rear View of the K-1500-EHF
Touch Tone (K-1900-5)
or
Pulse Dialer (K-1900-4)
(not included)
C.O. Line or
analog
PABX/KSU
extension
B. Wiring the K-1500-EHF
Touch Tone (K-1900-5)
or
Pulse Dialer (K-1900-4)
(not included)
Top View
2.10
Side
View
EMERGENCY
PHONE
MODEL K-1500-EHF
VIKING
1.60
0.70 6.86
9.875
8.50
0.675
Front View
(2) .3 diameter
mounting holes
Internal View of an Elevator
Open
12
34
56
78
1 2 3 4 5 6 7 8
Notes: Talk battery must be a minimum of 28V DC when using the K-1500-EHF in conjunction with a
Hot-Line Dialer. For more information regarding Hot-Line Dialers, retrieve Fax Back Document 833.
C.O. Line or
analog
PABX/KSU
extension
VIKING©
Programmable
Tone Dialer
MODEL: K-1900-5
Viking Electronics, Inc.
Hudson, WI 54016
VIKING©
Programmable
Tone Dialer
MODEL: K-1900-5
Viking Electronics, Inc.
Hudson, WI 54016
K-1500-EHF Programming
B. Adjusting Speaker Volume
A. Changing the Call Time-Out
D. Disabling the Auto-Answer feature
The K-1500-EHF is factory set to auto answer when an inbound call is
detected. To disable this feature, cut the resistor shown through the hole on
the back of the circuit board as shown to the right. Important: Disconnect
the telephone line before cutting the auto-answer resistor.
The K-1500-EHF is equipped with an adjustable call time-out feature which
automatically hangs up the K-1500-EHF after the time-out has elapsed. To
change the time-out, adjust the call time as shown to the right. The time can be
adjusted from approximately 30 sec to 6 min (factory set to approximately 3 min).
C. Adjusting the Microphone Volume
In certain noisy locations (background traffic, machinery or wind), the
microphone volume may need to be decreased. A symptom of this is one-way
talk path, in which the distant party cannot be heard over the speaker. A MIC
ADJ pot is provided on the K-1500-EHF for increasing or decreasing the
microphone sensitivity. Note: If the microphone volume is set too high or too
low, one-way talk path may occur.
The SPKR VOL pot can be adjusted to increase or decrease the speaker
volume to the level desired as shown to the right.
++
+
+
Speaker Volume
+
Microphone Volume
+
Call Time Out
Rear View of PCB
Cutout to disable
Auto-Answer
AUTOMATICALLY DISCONNECTS
30 sec 6 min
PUSH
TO
CALL