Viking E-1600-ASTIPEWP User manual

QUICK START GUIDE
VIKING Electronics, Inc.
KSee Product Manual for complete installation and programming instructions.
1.0 Out-of-Box
1.1 Verify that you have received all of the parts listed
1.2 Download the product manual
1. Go to www.vikingelectronics.com and enter
E-1600-ASTIPEWP in the search box
2. Click E-1600-ASTIPEWP in the search results
3. Click Product Manual to open and download
the PDF
1.3 Download and install the programming software
1. Go to www.vikingelectronics.com and enter E-1600-ASTIPEWP in the search box
2. Click E-1600-ASTIPEWP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on
setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
2.0 Power Source
Select PoE Switch or PoE Injector that meets the following requirements:
1. IEEE 802.3af / 802.3at / 802.3bu compliant
2. Capable of providing at least 4 Watts (class 1)
Note: CAT5e (or higher) cable recommended
X 1 Assy Final
X 1 Assy Strobe Panel
X 1 Chassis E-1600-BLTIPEWP
X 1 Torx T-10 Security Bit
X 8 Screw Flat head Torx Drive
6-32 x 3/4 Stainless Steel
X 1 Black, Red and Green Wires
bundled with Cable Tie
X 2 Panel Gasket
X 1 Hood
X 2 5-16 x 2.5 in. Lag Screw
X 2 Washer 5/16 Fender
X 6 Gel-Filled Butt Connectors
X 1 Transformer 12VDC
Scan the QR code to
open and download
the product manual - OR -
E-1600-ASTIPEWP
VoIP Emergency
Phone
January 15, 2019

4.0 Features Overview
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
E-1600-ASTIPEWP Quick Start Guide ZF303713 REV A
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full duplex
• Disable Spanning Tree Protocol (STP) or enable Portfast
3.0 Network Port Settings
Rear (PCB) View of the Phone Panel
Connect to SL-2
Strobe Light,
included (see pg 6 in
Product Manual
for proper wiring)
MAC:
18E80FXXXXXX
asdesaxtff
N.C. (Gray)
N.O. (Yellow)
COM. (Blue)
2 Amp Relay
Output Contacts
(2A@30VDC/ 250VAC max)
- Black
+ Red
Black
Black
- Black
+ Red
LED
Help Switch
Info Switch (model
E-1600BLT2IPEWP only)
Speaker
Microphone
MAC Address Label: The
MAC address is aunique 12
digit number used by routers
to send network traffic to the
correct IP address.
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect
to your LAN via RJ45 plug
and CAT5 or greater twisted
pair wire.
Yellow Network Status LED:
Lights steady to indicate power
and data link. Blinks to indicate
network activity.
Green Unit Status LED
Red
Red
White
White
120V AC
12V DC Adapter
(included)
-
+