Vimar Eikon User manual

Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
20592.0 01 2105
EIKON
20592.0
ARKE'
19592.0-19592
IDEA
16492
PLANA
14592-14592.0
Connected 2-way switch
20592.0-19592.0-14592.0: to be completed with 1- or 2-module interchangeable buttons.
19592-16492-14592: complete with button.
The device is equipped with 2 interlocked relay outputs for the switch function and it can also be
connected to existing wired multi-way/two-way switches to make the load function “connected”.
TWO OPERATING MODES (ALTERNATIVE)
or
Download the View Wireless App from the stores onto the tablet/smartphone you
will be using for configuration.
Depending on the mode you select, you will need:
Gateway
art. 20597-19597-16497-14597
Zigbee Gateway
(Amazon Echo Plus, Echo Show or Echo
Studio)
Alexa App
View App
for management via smartphone/tablet
Amazon Alexa, Google Assistant, Siri and
Homekit voice assistants for possible
voice operation
CONFIGURATION IN
1. Create your Installer account on MyVimar (on-line).
2. Wire all the devices in the system (2-way switches, actuators, thermostats, gateway, etc.).
3. Start the View Wireless App and log in with the credentials you just created.
4. Create the system and the environments.
5. Associate all the devices with the environments, except for the gateway (which should be
associated last).
To associate the 2-way switch:
• Select “Add” ( ), choose the environment to place it and give it a name
• Select ; activate the Bluetooth connection on your tablet/smartphone and approach the
2-way switch
• Press the button on the 2-way switch and set the desired function
6. For every device, set the function, the parameters and any accessory devices (wired or radio
control and related function).
7. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.
8. Transfer the system to the Administrator user (who must have created his/her profile on
MyVimar).
For details please refer to the View Wireless App manual you can download from www.
vimar.com DOWNLOAD View Wireless MOBILE App
CONFIGURATION IN
Follow the procedure above from points 1to 3.
Associate the 2-way switch directly with Amazon Echo Plus, Echo Show or Echo Studio.
1) Press the button on the 2-way switch until the LED flashes. Download the Zigbee software
onto the device using the View Wireless App (see the View Wireless App manual).
To update the software on the device, the procedure is the same.
2) After conversion to Zigbee technology (or the software update), the 2-way switch automatically
goes into pairing mode so that it can be recognised by the Amazon device within 5 minutes.
If the 2-way switch is not in pairing mode, cut off the power supply and restore it after a few
seconds.
3) Associate the 2-way switch with Amazon Echo Plus, Echo Show or Echo Studio according to
the procedure envisaged by the voice assistant (see the Amazon documentation).
Set the actuator parameters.
1) Within the first 5 minutes after the device has been powered (already associated with Amazon
Alexa), press the button for 15 s; this way, you can select the relay operation - between one-po-
sition stable and two-position stable (the LED flashes green for the two-position stable setting
and amber for the one-position stable setting).
2) Briefly press the button to switch from two-position stable to one-position stable and vice
versa; once the choice has been made, press the button for 5 s to confirm. If you have set the
two-position stable setting, the LED flashes green three times, whereas if you have chosen the
one-position stable setting, you will move on to the next step (3).
3) Press the button for 5 s to set the one-position stable activation time. Press the button briefly,
the output is activated and the LED lights up amber permanently; at the end of the time you
wish to set, press the button again. The output is deactivated and the LED flashes amber for 3
times to confirm the setting made.
N.B. When the voltage returns after a power outage, the relay maintains the state in which it was
prior to the power supply cut out.
Summary of Zigbee technology mode signalling.
• During normal operation:
LED Meaning
On
(amber for Eikon, blue for Arké, green for Idea and
Plana)
Relay active
Off Relay not active
• In the configuration phase:
LED Meaning
Flashing white
(for max 5 min.) Zigbee mode active pending voice assistant
Flashing blue
(for max 2 min.) Pending receipt of a fw update
Blue permanently lit Device associated with the smartphone via
Bluetooth
Flashing green during the one-position
stable/two-position stable configuration
(for max 5 min.)
Setting in two-position stable
Flashing amber during the one-position
stable/two-position stable configuration
(for max 5 min.)
Setting in one-position stable
Amber permanently lit One-position stable time setting
Flashing green 3 times Confirms two-position stable setting
Flashing amber 3 times Confirms one-position stable setting
Flashing green quickly 3 times Device correctly associated with the voice
assistant
On
(amber for Eikon, blue for Arké, green for
Idea and Plana)
Relay active during normal operation
CONTROLLABLE LOADS.
For correct load state signalling, connect a 2 W minimum load.
Loads
- maximum
100 V~ 250 W 50 W 60 W 125 VA
240 V~ 500 W 100 W 120 W 250 VA
RESETTING THE DEVICE.
The reset restores the factory settings. Within the first 5 minutes from powering, press the
button for 30 s until the white LED flashes.
INSTALLATION RULES.
• Installation must be carried out by qualified persons in compliance with the current regula-
tions regarding the installation of electrical equipment in the country where the products are
installed.
• The device must be completed with interchangeable buttons and installed in flush mounting
boxes or surface mounting boxes with Eikon, Arkè and Plana mounting frames and cover
plates.
• The relay output power circuit must be protected against overloads by installing a device, fuse
or automatic 1-way switch, with a rated current not exceeding 10 A.
• Installation must be carried out with the system switched off. Install the buttons onto the
switch mechanism before powering up the system.
IMPORTANT: the electronic switch must be powered with the same L and N that power
the load. In the event of installation with wired multi-way/two-way switches, the electronic
switch should be connected so that it is always powered and therefore should be installed
instead of the wired two-way switch furthest from the load.
CHARACTERISTICS.
• Rated supply voltage: 100-240 V~, 50/60 Hz.
• Dissipated power: 0.55 W
• RF transmission power: < 100mW (20dBm)
• Frequency range: 2400-2483.5 MHz
•Terminals:
- 2 terminals (L and N) for line and neutral
- 1 terminal (P) for connection to the remote wired control (for instance art. 20008-19008-
16080-14008). The max distance between the IoT device and the push button is 50 m
with a cable with a minimum cross-section of 1.5 mm2.

Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
20592.0 01 2105
EIKON
20592.0
ARKE'
19592.0-19592
IDEA
16492
PLANA
14592-14592.0
Connected 2-way switch
WEEE - User information
The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately
from other waste. The user must therefore hand the equipment at the end of its life cycle over to the appropriate municipal centres for the
differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you
want to dispose of free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver electronic
products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area
of at least 400 m2. Proper sorted waste collection for subsequent recycling, processing and environmentally conscious disposal of the old
equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing and/
or recycling materials used in manufacture.
- 2 terminals (1 and 2) for the switch output
• Front button that is used both to control the load and as a configuration push button.
• RGB LED indicating the load status (which can be set from the View Wireless App) and the
configuration status (flashing blue)
• In Bluetooth technology mode, you can associate up to 2 radio devices (art. 03925) which make
it possible to control the actuator or activate a scenario.
• Operating temperature: -10 ÷ +40 °C (indoor)
• Protection degree: IP20
• Configuration from View Wireless App for Bluetooth technology system and Amazon App for
Zigbee technology.
• Controllable via View App.
OPERATION IN Bluetooth technology MODE.
The device operates by default in Bluetooth technology mode and this standard makes it pos-
sible to:
- recall a scenario using the traditional push button connected to the connected switch;
- associate the radio control 03925 which can be configured to control the actuator on-board
or to recall a scenario.
Through the use of gateway 20597-19597-16497-14597 the functions can be managed locally
or remotely via the View App, and the control is also available via the voice assistants Amazon
Alexa, Google Assistant and Siri.
The device is also compatible with Homekit.
N.B.: From fw version 1.7.0, the device works as a repeater node for battery-operated devices
(for instance art. 03980).
Apple HomeKit is a trademark of apple Inc. App Store is a service mark of Apple Inc. To control this HomeKit-enabled accessory, iOS 9.0 or later is recommended. Controlling this HomeKit-enabled accessory
automatically and away from home requires an apple TV with tvOS 10.0 or later or an iPad with iOS 10.0 or later or a HomePod/Siri set up as a home hub.
The Apple logo, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other countries and regions. App Store is a service mark of Apple Inc.
Google, Google Play and Google Home are trademarks of Google LLC.
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
Settings.
The View Wireless App can be used to set the following parameters:
- RGB LED for backlighting: colour can be selected from a default list (default: amber for Eikon,
blue for Arké and green for Plana).
- LED brightness: off, low, medium, high for active load (default: high) and for off load (default: off).
- Load status when the voltage is restored: off, on or previous status (default: previous status).
- Relay operation: two-position stable or one-position stable (default: two-position stable).
- One-position stable activation time (default: 60 s).
REGULATORY COMPLIANCE.
RED Directive. RoHS directive.
Standards EN 60669-2-1, EN 301 489-17, EN 300 328, EN 62479, EN 50581.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text
of the EU declaration of conformity is on the product sheet available on the following website:
www.vimar.com
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
FRONT AND BACK VIEW
6 mm
P2 1 L
μ
N
Output for connection to a reversing switch or an electro-mechanical switch
Input for wired push button: remote control (for Bluetooth technology and Zigbee technology
mode) or scenario recalling (only for Bluetooth technology mode)
LED
L
N
Button

Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
20592.0 01 2105
CONNECTIONS
L
N
20008 20592.0
6 mm
P2 1 L
μ
N
10mm
L
1
20008
10mm
L
1
20008
10mm
L
1
Example of a two-way switch with traditional push buttons in a new system. For lighting devices with relays.
PUSH BUTTON PUSH BUTTON PUSH BUTTON
L
N
20008 20592.0 20013 20005
6 mm
P2 1 L
μ
N
12
L1 L2
10mm
10mm
L
1
2
10mm
L
1
* Can recall a scenario involving lights/roller shutters/socket outlets controlled in the system (only for Buletooth technology mode).
IMPORTANT: the electronic switch must be powered with the same L and N that power the load. In the event of installation with wired multi-way/two-way switches, the electronic switch should be
connected so that it is always powered and therefore should be installed instead of the wired two-way switch furthest from the load.
REVERSING SWITCH SWITCH
Example of a light circuit with push buttons and relays in a new system.
PUSH BUTTON*
Connecting an individual lighting device
L
N
20592.0
6 mm
P2 1 L
μ
N