virtual access GW2040 Series User manual

Virtual Access GW2040 Series
Quick Start Guide

Table of contents
1Preface.................................................................................................... 3
1.1 Safety instructions ................................................................................. 3
1.2 Electrical safety...................................................................................... 3
1.3 Wireless safety....................................................................................... 3
1.4 Product disposal..................................................................................... 4
2Introduction ............................................................................................ 5
2.1 GPRS ...................................................................................................... 5
2.2 HSDPA.................................................................................................... 5
2.3 HSUPA.................................................................................................... 5
2.4 UMTS...................................................................................................... 5
2.5 EDGE ...................................................................................................... 5
2.6 CSD in EGSM900/GSM1800 MHz............................................................. 5
2.7 More information.................................................................................... 6
3Getting started ........................................................................................ 7
3.1 Serial number......................................................................................... 7
3.2 Inserting the SIM card ........................................................................... 7
3.3 Connecting the antenna ......................................................................... 7
3.3.1 Antenna diversity ................................................................................... 8
3.4 Connecting the power supply ................................................................. 8
4LED behaviour ......................................................................................... 9
4.1 Main LED behaviour................................................................................ 9
4.2 Ethernet switch LED behaviour............................................................. 10
5Configuring the GW2040 Series for 3G access....................................... 11
5.1 Optional automatic configuration......................................................... 11
5.2 Manually configuring a GW2040 Series router ..................................... 11
5.3 Configuring the APN and PIN ............................................................... 13
5.4 Configure authentication options ......................................................... 13
5.5 Save the configuration ......................................................................... 14
5.6 Reload the configuration ...................................................................... 14
5.7 Connection Monitor .............................................................................. 14
6File system ............................................................................................ 15
6.1 Managing configuration files ................................................................ 15
6.1.1 Managing configuration via the web interface............................................15
6.1.2 Managing configuration via the command line...........................................17
6.2 Managing firmware .............................................................................. 18
6.2.1 Managing firmware via the web interface..................................................18
6.2.2 Managing firmware via the command line.................................................19
7Firmware updates information .............................................................. 21
8Troubleshooting .................................................................................... 22
Copyright 2013 Virtual Access (Irl) Ltd. This material is protected by copyright. No part of this material may be reproduced,
distributed, or altered without the written consent of Virtual Access. All rights reserved. Third party trademarks are the property
of the third parties.
Virtual Access GW2040 Series Quick Start Guide
Issue: 1.2 Page 2 of 22

1: Preface
1Preface
1.1 Safety instructions
The router is complicated electronic equipment that may be repaired only by authorised
and qualified personnel.
•Do not try to open or repair the router yourself.
•Do not place the router in a damp or humid place.
•Do not stack the router.
•The router should be used in a sheltered area, within a temperature range of 0oC
to 40oC.
•Do not expose the router to direct sunlight.
HIGH VOLTAGES
Under no circumstances is the router to be operated with the cover removed.
DANGEROUS SUBSTANCES
Semiconductor devices contain dangerous substances, such as beryllium and arsenic.
Electronic devices must not be opened. If they become damaged, they must only be
handled using protective gloves. If the substances inside the electronic devices come into
contact with broken skin or wounds, hospital care must be sought immediately.
Electronic components must be disposed of as hazardous toxic waste and must not be
incinerated.
1.2 Electrical safety
The GW2040 Series router is a class I/II apparatus.
We recommend that an AC surge arrestor is installed in the AC outlet to which this
equipment is connected.
Plug in the power supply into a socket outlet that is installed near the equipment and is
easily accessible.
1.3 Wireless safety
Wireless routers incorporate a wireless radio module. Ensure the antenna is positioned at
least one metre away from you and other people in normal operation.
If in a hospital or health care facility, do not use the router in areas where guidelines to
switch off mobiles phones are posted. Medical equipment may be sensitive to RF energy.
The operation of cardiac pacemakers, other implanted medical equipment and hearing
aids can be affected by interference from wireless routers when placed close to the
device. People with pacemakers are advised to keep the wireless router away from the
pacemaker while it is on.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 3 of 22

1: Preface
Do not operate your wireless router in the presence of flammable gases, fumes or
potentially explosive atmospheres. Wireless routers should not be used anywhere that
blasting operations are taking place.
Wireless routers operate using radio signals and cellular networks cannot be guaranteed
to connect in all possible conditions. Therefore, you should not rely solely on any wireless
device for life-critical communications.
1.4 Product disposal
The United Kingdom and Republic of Ireland are under an obligation to minimise the
disposal of Waste Electrical and Electronic Equipment (WEEE) in domestic waste and
encourage recycling, recovery and environmentally sound disposal. Virtual Access is
committed to promoting the reuse, recycling and recovery of WEEE by contributing to the
appropriate compliance schemes.
Our product packaging is marked with the crossed out wheeled bin symbol to indicate
that the product must not be disposed of in domestic waste but disposed of through an
approved WEEE take back scheme. For details of your local collection facilities, please
contact your local authority.
Virtual Access WEEE registration number: WEE/CA2530XZ.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 4 of 22

2: Introduction
2Introduction
This configuration guide explains how to set up and configure a 3G connection on a
Virtual Access GW2040 Series router.
3G is the third generation of mobile phone standards and technology. It is based on the
International Telecommunication Union (ITU) family of standards under the International
Mobile Telecommunications programme, IMT-2000.
3G technologies enable network operators to offer users a wider range of more advanced
services while achieving greater network capacity through improved spectral efficiency.
Services include wide-area wireless voice telephony, video calls, and broadband wireless
data, all in a mobile environment.
The GW2040 Series contains a GSM (Global System for Mobile communications) 3G
wireless modem. The modem together with a SIM card establishes a WAN connection to
the Internet or private network.
Data bearers are frame protocols that transport data streams. The GSM (3G) modem
supports GPRS, Edge, HSDPA, HSUPA, UMTS and CSD.
2.1 GPRS
GPRS (General Packet Radio Service) uses packet-switched technology to transmit small
bursts of data. The 3G modem on the GW2040 Series supports multi-slot class 6, which
allows a maximum data rate of 384Kbps class 3. The maximum data rate available to the
3G modem depends on provisioning by the network operator.
2.2 HSDPA
HSDPA (High-Speed Downlink Packet Access) uses circuit-switched technology to
transmit data at speeds of up to 7.2Mbps.
2.3 HSUPA
HSUPA (High-Speed Uplink Packet Access) is a 3G mobile protocol with up link speeds of
5.76Mbps
2.4 UMTS
UMTS (Universal Mobile Telecommunications System) is a 3rd generation technology
providing higher transfer rates.
2.5 EDGE
EDGE uses the same frequencies as GPRS but offers better speeds. It is used when the
signal strength for 3G is not sufficient.
2.6 CSD in EGSM900/GSM1800 MHz
CSD (Circuit-Switched Data) mode enables the 3G modem to transmit data over the
EGSM (Extended Global System for Mobile communications) frequency or the GSM
frequency. The modem behaves as a dual-band mobile phone behaves
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 5 of 22

2: Introduction
2.7 More information
For a digital copy of this guide and more detailed GW2040 information about:
•Configuring a GSM Modem on a GW2040, and
•SIM Management on a GW2040
visit http://www.virtualaccess.com/customer-support.php
For more detailed router configuration information, read the Advanced Configuration
section:
http://www.virtualaccess.com/smg-docs/start.htm
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 6 of 22

3: Getting started
3Getting started
3.1 Serial number
When you receive your GW2040 Series package retain the outer packaging. The label
containing the model number, serial number (S/N) and part number (P/N) is located on
the side of the packaging box.
Each GW2040 Series router is assigned a unique serial number. Record your device serial
number on your warranty card or somewhere you can easily access it. You must
reference your unique serial number (S/N) when you contact your distributor or Virtual
Access support for installation and configuration confirmation or should you request
service on the device.
Figure 1: The GW2040 label on the side of the packaging
Unpack the contents. There is a matching label located on the bottom of the router.
Figure 2: The GW2040 label on the bottom of the router
3.2 Inserting the SIM card
1. Ensure the unit is powered off.
2. Hold the SIM card with the chip side facing down and the cut corner top left.
3. Gently push the SIM card into SIM slot 1 until it clicks in.
4. To remove the SIM card, gently push the SIM card. The card will click out.
WARNING
The SIM card MUST be inserted into the router before the unit is powered on.
Do not insert or remove the SIM card after the unit has been powered on.
3.3 Connecting the antenna
The GW2040 is shipped with one antenna suitable for the model you ordered. If you
require antenna diversity, contact your reseller.
Screw the antenna into the back MAIN SMA connector.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 7 of 22

3: Getting started
3.3.1 Antenna diversity
The GW2040 has an AUX connector for connection of a second antenna to allow for
antenna diversity. Antenna diversity helps improve the quality and reliability of a wireless
link by mitigating problems associated with multipath distortion.
Multipath distortion is a form of RF interference that occurs when a radio signal has more
than one path between the receiver and the transmitter. It commonly occurs when there
is no clear line of sight between the transmitter and receiver and instead the signal is
reflected off hard surfaces such as shelves, ceilings and walls.
3.4 Connecting the power supply
1. Plug the power cable into an electrical socket suitable for a DC12V/1A power
supply.
2. The router initialises. The Power LED lights green, the CONFIG LED flashes, and
all the LEDs temporarily light in sequence. Then your router activates.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 8 of 22

4: LED behaviour
4LED behaviour
4.1 Main LED behaviour
The GW2010 and GW2040 Series router has a single colour LED. When the router is
powered on, the LED is green.
Figure 3: Example of LED activity: power and config are on
The possible LED states are:
•Off
•Flashing slowing
•Flashing quickly
•On
The following table describes the possible LED behaviour and meaning.
Power LED Off No power
On Power
Config LED
Off Error reading config from flash. Normally this means an unrecognised command in the boot configuration file in
flash.
Flashing slowly Unit running in recovery mode.
Flashing quickly Unit running in factory configuration.
On Unit running a valid configuration file.
SIM LEDs
Off SIM not selected or the SIM is not inserted.
Flashing
SIM selected and not registered on the network.
On
SIM selected and registered on the network.
Signal LEDs
None IPCP not connected.
1 IPCP connected and signal strength <= -89dBm.
2 IPCP connected and signal strength >= -89dBm AND <=-
69dBm.
3
IPCP connected and signal strength >-69dBm
All LEDs
flashing
slowly in
synchronisati
on
The unit has lost its application firmware and is no longer
operational.
Table 1: LED behaviour
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 9 of 22

4: LED behaviour
4.2 Ethernet switch LED behaviour
The Ethernet switch has two LEDs per port: a link LED (green) and a speed LED (amber).
When looking at the switch the LED on the left hand side is the link LED, and on the right
hand side is the speed LED.
Figure 4: Ethernet LED activity
Link LED
Off No physical Ethernet link detected.
Flashing Data being transmitted or received on the Ethernet port.
On Physical Ethernet link detected.
Speed Off 10M Ethernet link
On
100M Ethernet link
All LEDs flashing
slowly in
synchronisation The unit has lost its bootloader and is no longer
operational.
Table 2: Ethernet switch LED behaviour
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 10 of 22

5: Configuring the GW2040 Series for 3G access
5Configuring the GW2040 Series for 3G access
Depending on the factory configuration installed on the GW2040 Series router, the device
either automatically self-configures or it requires manual configuration.
5.1 Optional automatic configuration
Virtual Access GW2040 Series routers can be automatically configured from a service
provider’s central management service using the automated configuration process.
The GW2040 Series router contacts a central server and automatically pulls down its run
time configuration.
To verify this setting, browse to the router’s start page. You can access the router’s start
page by plugging an Ethernet cable into port A on the Ethernet switch.
The GW2040 Series router is configured as a DHCP server. The default IP of the router is
192.168.100.1/24.
From the start page, click Advanced -> Expert View to check that your router has
been configured for automatic configuration.
For the automated configuration process, the Factconf Name: field should show
‘GWXXXX_Zero; and the Factconf Type: field should show ‘activation’.
Figure 5: The GW2040 system information for automatic configuration
Contact your service provider to avail of this service.
5.2 Manually configuring a GW2040 Series router
To manually configure your GW2040 Series router with 3G check that the router has
been pre-loaded with a manual factory configuration. The manual factory configuration
for this model comprises settings for basic Internet connectivity of 3G data services.
To verify this setting, browse to the router’s start page. You can access the router’s start
page by plugging an Ethernet cable into port A on the Ethernet switch.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 11 of 22

5: Configuring the GW2040 Series for 3G access
Figure 6: The start page
The GW2040 Series router is configured as a DHCP server. The default IP of the router is
192.168.100.1/24.
When the start page has opened, click Advanced -> Expert View to check that the
router has been supplied for manual configuration. The Factconf Name: field should show
‘GWXXXX_man; the Factconf Type:field should show ‘manual’.
Figure 7: The GW2040 system information for manual configuration
Once you confirm that the router has a manual factory configuration installed, you can
proceed to configure the following parameters:
•APN
•SIM PIN (if using 3G)
•PPP Username and password
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 12 of 22

5: Configuring the GW2040 Series for 3G access
5.3 Configuring the APN and PIN
1. To set the APN and PIN, browse to the router’s start page and click Advanced ->
Expert View -> interfaces -> modem-0 -> gsm. The Modem Interface on
GSM page appears.
Figure 8: The modem interface on GSM
2. Type in the APN and PIN details.
3. Click Update and save to flash. Note which configuration you have committed
the changes to. For more information, read section 4.5, ‘Save the configuration’.
5.4 Configure authentication options
Access to each PPP interface can be restricted based on a username and password.
1. In the Expert View menu, click interfaces -> ppp-1 (3G) -> ppp-
>authentication->name and password. The Username and Password page
appears.
Figure 9: The username and password page
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 13 of 22

5: Configuring the GW2040 Series for 3G access
2. Enter in the relevant details, click Update and save to flash.
Note: password validation does not require a minimum length or the use of numeric
characters.
5.5 Save the configuration
1. In the Configuration Update Result page, click Save to flash. The Save
Configuration to Flash page appears.
2. In the drop-down menu select the configuration you want to save changes to and
click Save.
There are 3 options to save to:
•Config 1
•Config 2
•Alternate Config
3. Select config 1.
For more information on config options, read section 6.1, ‘Managing configuration files’.
5.6 Reload the configuration
1. In the Expert View menu, select set boot configuration.
2. In the drop-down menu, select the configuration option you have chosen to save
to.
3. Click Select, then select reload.
5.7 Connection Monitor
To check the status of each of the connections, in the Advanced menu, click Connection
Monitor. The Connection Monitor page appears.
Figure 8: The Connection Monitor interface
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 14 of 22

6: File system
6File system
6.1 Managing configuration files
The GW2040 has three configuration file segments in flash: factonf, config1 and config2.
Routers are shipped in factory configuration. Live routers will toggle between config1 and
config2. When you make configuration changes it is good practise to save to the
alternate configuration segment for recovery to the original configuration if problems
occur. Changing the active configuration file requires a reload to take effect.
6.1.1 Managing configuration via the web interface
To view the active configuration, from the start page, click Advanced.
In the Advanced menu, click Diagnostics.
Figure 10: The diagnostics page
To change the boot configuration file, from the start page, click Advanced.
In the Advanced menu, click Expert View->set boot configuration.
Figure 11: The next boot configuration page
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 15 of 22

6: File system
To view any of the configuration files, from the start page, click Advanced.
In the Advanced menu, click Expert View->Configuration Files.
Figure 12: The Config 1 page
To upload any of the configuration files to your local PC, from the start page, click
Advanced.
In the Advanced menu, click Expert View->Configuration Files->upload from
router.
Figure 13: The configuration file upload page
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 16 of 22

6: File system
6.1.2 Managing configuration via the command line
Command line: show ident
Display the operating and web software version information.
Figure 14: Output showing operating and web software version information
Command line: show current config
Display the name of the configuration file that is currently running.
Figure 15: Output of the command line show current config
Command line: show next config
Display the name of the configuration file that will load the next time the device reloads.
Figure 16: Output of the command line show next config
set next config <configFile>
Make the configuration file held in flash the file to be used the next time the system
boots. The table below shows the 4 file options.
factconf Use the configuration stored in the factory configuration file the
next time the system boots.
config1 Use the configuration stored in config1 the next time the system
boots.
config2 Use the configuration stored in config2 the next time the system
boots.
altconfig If config1 is running, use the configuration stored in config2 the
next time the system boots.
If config2 is running, use the configuration stored in config1 the
next time the system boots.
Table 3: The possible strings for the set next config command
Figure 17: Output of the command line set next config
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 17 of 22

6: File system
Command line: show cfg
Display the running configuration file
Command line: show factconf
Display the factcory configuration file
Command line: show config1
Display config1
Command line: show config2
Display config2
6.2 Managing firmware
The GW2040 firmware consists of two deliverables - an ‘.img’ extension image file that
defines the operation of the router and a ‘.web’ extension web file for the embedded web
server.
The GW2040 has two flash segments available for the image: image1 and image2. Only
one segment will be active. It is good practise to upgrade image firmware to the
alternate image segment. Changing the active image requires a reload to take effect.
6.2.1 Managing firmware via the web interface
To view the active image, from the Start page, click Advanced.
In the Advanced menu, click Diagnostics.
Figure 18: The diagnostics page
To change the active image, from the start page, click Advanced> Expert View.
In the top menu, click Operations.
In the Operations menu, click file transfers->set boot image.
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 18 of 22

6: File system
Figure 19: The next boot software (program) image page
6.2.2 Managing firmware via the command line
Command line: show system software version
Display the operating software version number.
Figure 20: Output of the command line show system software version
Command Line: show system software variant
Display the operating software country code.
Figure 21: Output of the command line show system variant Command line: show current
image
Display the name of the operating software image file that is currently running.
Figure 22: Output of the command line show current image
Command line: set next image <filename>
Make the image held in flash in segment filename the one that will be used the next time
the system boots.
Figure 23: Output of the command line set next image
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 19 of 22

6: File system
Image 1
Image stored in image segment 1
Image 2 Image stored in image segment 2
Alt image Image stored in image segment that is not currently running.
(Show current Image)
Table 4: Descriptions of image command
Command line: show next image
Display the name of the operating software file that will be loaded the next time the
device reloads.
Figure 24: Output of the command line show image
Virtual Access GW2040 Series Quick Start Guide © Virtual Access Ltd.
Issue: 1.2 Page 20 of 22