Vision Fitness X1400 User manual

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2006 Vision Fitness. All Rights Reserved. 6.06
AG18.34PRD
REV6
starts
vision
with a
it all
Assembly
Guide
X1400 AND X1500
ELLIPTICAL TRAINERS
ORANGE BAG
PINK BAG
GREEN BAG
M8 Nut
Quantity: 4
M5x12L Bolt
Quantity: 12
M8x15L Bolt
Quantity: 2
8x17x1T Washer
Quantity: 4
M8X15L Bolt
Quantity: 6
8x16x1.5T Washer
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
8x25x1.5T Washer
Quantity: 2
M8x45L Bolt
Quantity: 2
BLUE BAG
M4x12L Bolt
Quantity: 2
8x38x2T Washer
Quantity: 2
4x10x1T Washer
Quantity: 2
Nylon Nut Cover
Quantity: 2
5x10x1T Washer
Quantity: 4
SS41 Link Joint Sleeve
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
M8x20L Bolt
Quantity: 2
8x38x2T Washer
Quantity: 2
M4x12L Screw
Quantity: 2
Nylon Interval Ring
Quantity: 4
TOOLS & PARTS INCLUDED
Screwdriver
5mm L-Shaped Wrench
PARTS BOX
13mm Wrench
Console Mast Boot
Dual-Action Link Arm Covers
Dual-Action Axle Covers
Pedal Arm Joint Covers
Right and Left Footplates
Rear Stabilizers
Water Bottle and Cage
Power Supply
Color Coded Hardware Bags
Owners Manual
Assembly Guide
Warranty Card
13mm Wrench
Quantity: 1
5mm T-Shaped Wrench
8x18x1T Arc Washer
Quantity: 2
SW8 Lockwashers
Quantity: 6
6x14x1T Washer
Quantity: 8
M8x20L Bolt
Quantity: 2

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2006 Vision Fitness. All Rights Reserved. 6.06
AG18.34PRD
REV6
starts
vision
with a
it all
Assembly
Guide
X1400 AND X1500
ELLIPTICAL TRAINERS
ORANGE BAG
PINK BAG
GREEN BAG
M8 Nut
Quantity: 4
M5x12L Bolt
Quantity: 12
M8x15L Bolt
Quantity: 2
8x17x1T Washer
Quantity: 4
M8X15L Bolt
Quantity: 6
8x16x1.5T Washer
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
8x25x1.5T Washer
Quantity: 2
M8x45L Bolt
Quantity: 2
BLUE BAG
M4x12L Bolt
Quantity: 2
8x38x2T Washer
Quantity: 2
4x10x1T Washer
Quantity: 2
Nylon Nut Cover
Quantity: 2
5x10x1T Washer
Quantity: 4
SS41 Link Joint Sleeve
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
M8x20L Bolt
Quantity: 2
8x38x2T Washer
Quantity: 2
M4x12L Screw
Quantity: 2
Nylon Interval Ring
Quantity: 4
TOOLS & PARTS INCLUDED
Screwdriver
5mm L-Shaped Wrench
PARTS BOX
13mm Wrench
Console Mast Boot
Dual-Action Link Arm Covers
Dual-Action Axle Covers
Pedal Arm Joint Covers
Right and Left Footplates
Rear Stabilizers
Water Bottle and Cage
Power Supply
Color Coded Hardware Bags
Owners Manual
Assembly Guide
Warranty Card
13mm Wrench
Quantity: 1
5mm T-Shaped Wrench
8x18x1T Arc Washer
Quantity: 2
SW8 Lockwashers
Quantity: 6
6x14x1T Washer
Quantity: 8
M8x20L Bolt
Quantity: 2

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order.
Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter
here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12.
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your
Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and
screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
Assembly
Guide
X1400 AND X1500
ELLIPTICAL TRAINERS
4
STEP
1
STEP
2
STEP
Stabilizer
Cover
1
STEP
ORANGE BAG
2
STEP
• Slide a wavy washer (25x34x2T) on
to the right rotation axle. Slide the
knuckle joint of the pedal arm assembly
onto the right rotation axle. The pedal
arm roller wheel should be placed into
the groove of the guide rail. Secure the
pedal arm assembly to the rotation axle
with a washer (8x38x2T) and bolt
(M8x20L). Tighten with the 5mm T-
shaped wrench.
• Place the pedal arm cover over the
knuckle joint. Secure in place with a
washer (4x10x1T) and bolt (M4x12L).
Tighten with the screwdriver.
• Repeat both steps on the left side.
BLUE BAG
3
STEP
• With the screwdriver remove the
bolts for the water bottle cage in the
center of the console mast. Slide the
rubber boot onto the console mast.
• Unfold the wire harness located in
the frame bracket. Wrap the end of
the wire tie, located at the bottom of
the console mast, around the end of
the wire harness. Pull the wire tie and
wire harness up through the console
mast while simultaneously sliding the
mast over the frame bracket.
• Slide a lock washer (SW8)
followed by a flat washer (8x17x1T)
onto four of the bolts (M8x15L). Insert
these bolts through the side of the mast
to secure the mast to the frame. Slide
a lock washer (SW8) followed by a
arc washer (8x18x1T) onto the two
remaining bolts (M8x15L). Insert these
bolts through the holes in front of the
mast. Tighten all bolts with the 5mm
T-shaped wrench.
• Slide the rubber boot down the
console mast and snap it in place
over the side covers.
• Remove the four bolts from the back
of the console. Connect the wire
harness to the plug in the back of the
console. Connect the heart rate wires
into the heart rate plugs in the back of
the console. Attach the console to the
console mast with the four console
bolts and screwdriver.
• Attach the water bottle cage to the
console mast with the two bolts
removed earlier in this step.
PINK BAG
4
STEP
• Slide the dual-action axle cover into
place over the console mast axle.
Slide a wavy washer (25x34x2T)
onto the console mast axle. Slide the
right dual-action arm onto the axle. Fix
in place with a washer (8x38x2T)
and nylon nut (M8). Cover with the
included nylon nut cover.
• Insert the link joint sleeve (SS41)
into the socket joint of the right link
arm. Position the socket joint of the
link arm into the bracket at the bottom
of the dual-action arm. Position the
Nylon Interval Rings between the
socket joint and bracket on each side.
Insert a bolt (M8x45L) through the
bracket, interval rings and socket joint
sleeve. Secure in place with a washer
(8x25x1.5T) and nylon nut (M8).
Tighten with the 5mm T-shaped
wrench and 13mm wrench.
• Position the link arm covers over the
socket joint and secure the two pieces
together with a screw (M4x12L).
Tighten with the screwdriver. Connect
the cover to each side of the link arm
with a washer (5x10x1T) and bolt
(M5x12L). Tighten with the
screwdriver.
• Position the right footplate onto the
right link arm. Secure in place with
four washers (6x14x1T) and four bolts
(M5x12L). Tighten with the screwdriver.
• Repeat steps on the left side.
• Attach the hand grips onto the dual-
action arms by turning grip in a
clockwise direction. Make sure it is tight.
GREEN BAG
3
STEP
Stabilizer
Shaft
Console
Mast
Console
Boot
Link Arm
Covers
Dual-Action
Axle Cover
Footplate
Dual-Action
Arm
Hand Grips
• Slide the stabilizer shaft through the
plastic sleeves in the rear support tube.
• Slide the stabilizer covers onto the
stabilizer shaft and secure with
(M8x20L) bolts and (8x16x1T) flat
washers. Tighten with the 5mm
T-shaped wrench.
• Attach end caps to the end of the
guide rails with (M8x15L) bolts. Tighten
with the 5mm T-shaped wrench.
End Cap
Pedal Arm
Cover
Pedal Arm
Assembly
Knuckle
Joint
Rotation
Axle
Hand Grips