manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Vision Fitness
  6. •
  7. Elliptical Trainer
  8. •
  9. Vision Fitness S7100 User manual

Vision Fitness S7100 User manual

S7100 ASSEMBLY GUIDE
HARDWARE INCLUDED
S7100
Suspension Elliptical Trainer
To avoid possible damage to this Suspension Elliptical™ Trainer, please follow assembly steps in the correct order. Before proceeding
though, find your new Suspension Elliptical™ Trainer’s two serial numbers located on the console mast frame bracket, and on the back
side of the console, and enter here:
Console Mast Frame Bracket Serial Number: ____________________________________
Console Serial Number: ________________________________________
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Suspension Elliptical™ Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Suspension Elliptical™
Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially
threaded in before completely tightening any ONE bolt or screw.
TOOLS & PARTS INCLUDED
ASSEMBLY GUIDE
HARDWARE INCLUDED
S7100
Suspension Elliptical Trainer
6mm L-Shaped Wrench x2
Screwdriver
5mm L-Shaped Wrench
1600 Landmark Drive • Cottage Grove, WI 53527
toll free 800.335.4348 • fax 608.839.8731
www.visionfitness.com
©2012 Vision Fitness. All Rights Reserved.
2012.06.21
REV8.2
15mm Wrench
Qty: 2
13mm Wrench
Assembly Guide
Power Cord
Incline Arm Covers (x2)
C r a n k A r m B e a r i n g E n d C a p s ( x 2 )
Elevation Bracket Cover
Color-coded Hardware Bags
PARTS BOX
M8 Nut
Quantity: 4
M8x90L Bolt
Quantity: 2
M8X30L Socket Head Bolt
Quantity: 4
M8 Flat Washer
Quantity: 4
M8 Nut
Quantity: 2 8.2x25x2.5T Washer
Quantity: 2
M8x15L Button Head Bolt
Quantity: 2
8.2x16x2T Washer
Quantity: 4
M8 Nut
Quantity: 2
M8x50L Bolt
Quantity: 2
Spacer Bushings
Quantity: 4
10.5x45x5T Washer
Quantity: 2
M10x25L Button Head Bolt
Quantity: 2
BLACK BAG
GREEN BAGPURPLE BAG
PINK BAG
M8x70L Socket Head Bolt
Quantity: 4 8.2x25x1.5T Washer
Quantity: 4
3/8x52L Socket Head Bolt
Quantity: 1
M8x20L Socket Head Bolt
Quantity: 4
10.2x15x1.5T Washer
Quantity: 1
M5x15L Bolt
Quantity: 10
BLUE BAG
LIGHT BLUE BAG
ORANGE BAG
8.2x16x1.5T Washer
Quantity: 4
STEP 7
STEP 6
STEP 5
STEP 4
STEP 3
STEP 2
STEP 1
NOTE: A second person will be helpful to
complete this step.
• Slide the console mast boot onto the
console mast.
• Using the two bolts inserted in the front
of the console mast as guides, set the
console mast into the console mast
frame bracket ensuring cables are not
pinched between the console mast and
console mast bracket. Secure the front
of the mast to the frame bracket with the
other two socket head bolts (M8x20L)
and (8.2x16x1.5T) washers using a 6mm
L-shaped wrench. Secure each side of the
console mast to the console mast bracket
with one socket head bolt (M8x20L) and
one washer (8.2x16x1.5T) using a 6mm
L-shaped wrench. Do NOT tighten the
bolts yet.
• Release the console mast elevation
bracket and slide it down the console
mast to its lowest position. Slide the
console mast elevation bracket (shaft
bracket) over the elevation motor tube
so the holes in the console mast elevation
bracket line up with the top holes in
the elevation motor tube. Insert the bolt
(3/8x52L) and washer (10.2x15x1.5T)
and tighten just to snug using a 6mm
L-shaped wrench. Do not allow the bolt to
draw tight and deform the tube.
• Tighten the six (M8x20L) bolts on the
mast completely tight using a 6mm
L-shaped wrench.
• Connect the data cables coming from the
bottom of the console mast to the data
cables coming up from the frame.
• Slide the console mast boot down over
the frame.
• Remove button head cap bolt, flat washer
and one wavy washer from the left hand
dual-action arm housing shaft. Then
slide the left dual-action arm on the left
housing and secure in place with a button
head cap bolt (M8x20L) wavy washer
and flat washer. Tighten with the 5mm
L-shaped wrench.
• Insert a spacer bushing onto each side
of the left hand link arm bearing. Slide
the link arm between the flanges of
the dual-action arm bracket. Insert a
button head screw (M8x50L) and flat
washer (8.2x16x2T); through the hole
to connect the brackets. Secure with a
washer (8.2x16x2T) and nylon nut (M8).
Tighten with the 5mm L-shaped wrench
and 13mm wrench.
• Repeat these steps on the right side.
• Take the left pedal assembly lay it on
the ground in position on the left side of
the machine and insert the bearing end
of the suspension arm into the bracket
of the incline arm. From the outside,
insert a hex head bolt (M8x90L) with
flat washer (M8) through the bracket
and suspension arm. Secure with a flat
washer (M8), and hex nut (M8). Fully
tighten with two 13mm wrenches. This
joint must be VERY tight.
• Repeat this step on right side.
• Take the front end of the left pedal arm
and insert it into the end of the crank
arm (You will have to slightly pry the
pedal arm out in order to place it into
the bearing). Rotate the crank arm/
pedal arm connection up to the 11 o’clock
position (1 o’clock right side) and insert
the button head bolt (M8x15L) with flat
washer (8.2x25x2.5T). Tighten with the
5mm L-shaped wrench.
• Press inner crank arm bearing end cap
in place.
• Repeat this step on the right side.
CONSOLES
PREMIER
DELUXE
NOTE: Do not fully tighten the four bolts
at the bottom of the incline arm until
instructed to do so in step 4.
• Slide the incline frame pivot shaft into
the incline pivot tube at the rear of the
unit.
• Slide the bottom of the left incline
arm over the incline pivot shaft and
let it rotate forward resting it on the
ground. Repeat on the right side.
NOTE: The incline frame pivot shaft
should be centered in the incline
pivot tube. Insert a button head bolt (
M10x25L) and washer (10.5x45x5T) into
each side of the incline frame pivot shaft.
Tighten the two button head bolts using
two 6mm L-shaped wrenches to pull the
incline arms in snug against the incline
pivot tube.
• Do NOT tighten the four bolts at the
bottom of the incline arm.
NOTE: A second person will be helpful to
complete this step.
• Lift the left incline arm and place a top
tube (they are interchangeable) over the
left incline arm bracket and connect with
two socket head cap bolts (M8x70L),
and two washers (8.2x25x1.5T). Turn
bolts finger tight with the 6mm L-shaped
wrench.
• Insert the pin on the elevation bracket
into the hole on the front flange of the
connection arm.
• Repeat these steps on the right side.
• With the screwdriver, remove the four
console mounting screws from the
backside of the console. Connect the
heart rate wires coming from the mast
to the heart rate wires coming from the
bottom of the console. Plug the data
cables into the board. Tuck any extra
wires into the console. Take care to
ensure cables coming from the frame sit
in the groove in the back of the console
and do not get pinched. Secure console
to the bracket using the four console
mounting screws removed earlier.
Tighten with the screwdriver.
• Position the cover over the elevation
bracket and secure with two bolts
(M5x15L).
• Position the covers over the rear of the
incline frame and secure each cover in
place with four bolts (M5x15L) each.
Tighten the bolts just until the covers
are snug.
• Plug the power cord into the power
socket in the front of the unit. Plug the
other end of the cord into the wall outlet.
Make sure the power switches at the
bottom of the unit and on the back of
the console are in the on position.
• When both top tubes are onto elevation
bracket alignment pin, lift the entire
assembly slightly to line up the bolt
holes. Insert the four socket head cap
bolts (M8x30L) through these holes.
Secure each bolt with a nylon nut (M8).
Do NOT tighten these bolts yet.
• Tighten the left and right top tube/
incline arm bolts using a 6mm L-shaped
wrench.
• Tighten the four elevation bracket bolts
(M8x30L) with the 6mm L-shaped
wrench and 13mm wrench.
• Tighten the four bolts at the bottom
lower-rear pivot of the incline arms using
a 6mm L-shaped wrench.
Please follow the order and intent of these
instructions as much as you can. The order
of assembly and order of tightening the
bolts will affect the performance of your
new exercise machine.
TIGHTEN
TIGHTEN
Console Mast
Data Cable
Console Mast
Frame Bracket
Console Mast
Boot
Elevation
Bracket
Incline Arm
Incline Frame
Pivot Shaft
Incline
Pivot Tube
Top Tube
Elevation
Bracket
Incline Arm
Incline Arm
Top Tube
Elevation
Bracket
Suspension
Arm
Crank Arm
Pedal
Assembly
Incline Arm
Bracket
Dual-Action
Arm
Dual-Action Arm
Housing Shaft
Link Arm
Incline Frame
Cover
Elevation
Bracket Cover
Elevation
Motor Tube
Heart
Rate Wires
Data Cables
BLUE BAG
BLACK BAG
LIGHT BLUE BAG
PURPLE BAG
ORANGE BAG
PINK BAG
GREEN BAG
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7

Other manuals for S7100

5

Other Vision Fitness Elliptical Trainer manuals

Vision Fitness R2150 Use and care manual

Vision Fitness

Vision Fitness R2150 Use and care manual

Vision Fitness X6000DA User manual

Vision Fitness

Vision Fitness X6000DA User manual

Vision Fitness S7100 User manual

Vision Fitness

Vision Fitness S7100 User manual

Vision Fitness X6150 User manual

Vision Fitness

Vision Fitness X6150 User manual

Vision Fitness S7100 User manual

Vision Fitness

Vision Fitness S7100 User manual

Vision Fitness X6000 User manual

Vision Fitness

Vision Fitness X6000 User manual

Vision Fitness X6100 User manual

Vision Fitness

Vision Fitness X6100 User manual

Vision Fitness X20 User manual

Vision Fitness

Vision Fitness X20 User manual

Vision Fitness X70 User manual

Vision Fitness

Vision Fitness X70 User manual

Vision Fitness XF40 User manual

Vision Fitness

Vision Fitness XF40 User manual

Vision Fitness X6150 User manual

Vision Fitness

Vision Fitness X6150 User manual

Vision Fitness X6600HRT User manual

Vision Fitness

Vision Fitness X6600HRT User manual

Vision Fitness S7200 User manual

Vision Fitness

Vision Fitness S7200 User manual

Vision Fitness X6200HRT User manual

Vision Fitness

Vision Fitness X6200HRT User manual

Vision Fitness S7100 User manual

Vision Fitness

Vision Fitness S7100 User manual

Vision Fitness X20 User manual

Vision Fitness

Vision Fitness X20 User manual

Vision Fitness X6750HRT User manual

Vision Fitness

Vision Fitness X6750HRT User manual

Vision Fitness X6100 User manual

Vision Fitness

Vision Fitness X6100 User manual

Vision Fitness T1450 User manual

Vision Fitness

Vision Fitness T1450 User manual

Vision Fitness X6600HRT/DA User manual

Vision Fitness

Vision Fitness X6600HRT/DA User manual

Vision Fitness X6200HRT User manual

Vision Fitness

Vision Fitness X6200HRT User manual

Vision Fitness S70-02 User manual

Vision Fitness

Vision Fitness S70-02 User manual

Vision Fitness X6200 Frame 9 User manual

Vision Fitness

Vision Fitness X6200 Frame 9 User manual

Vision Fitness X6600HRT User manual

Vision Fitness

Vision Fitness X6600HRT User manual

Popular Elliptical Trainer manuals by other brands

Schwinn 520 Reclined Elliptical Assembly manual

Schwinn

Schwinn 520 Reclined Elliptical Assembly manual

Sunny SF-E3628 user manual

Sunny

Sunny SF-E3628 user manual

NordicTrack E 7.2 Elliptical Uživatelská příručka

NordicTrack

NordicTrack E 7.2 Elliptical Uživatelská příručka

AFG 2.5 ae owner's manual

AFG

AFG 2.5 ae owner's manual

SOLE E95 owner's manual

SOLE

SOLE E95 owner's manual

NordicTrack 831.23954.1 user manual

NordicTrack

NordicTrack 831.23954.1 user manual

CAPITAL SPORTS Helios 10040072 manual

CAPITAL SPORTS

CAPITAL SPORTS Helios 10040072 manual

Weslo Eclipse 2 WLEMEL45071 user manual

Weslo

Weslo Eclipse 2 WLEMEL45071 user manual

Precor HANDBOEK EFX 556i Owner's manual addendum

Precor

Precor HANDBOEK EFX 556i Owner's manual addendum

Gold's Gym Stride Trainer 410 user manual

Gold's Gym

Gold's Gym Stride Trainer 410 user manual

Cubii JR1+ owner's manual

Cubii

Cubii JR1+ owner's manual

Xterra 16604701500 owner's manual

Xterra

Xterra 16604701500 owner's manual

Merach MR-632 user guide

Merach

Merach MR-632 user guide

Boomerang 850 user manual

Boomerang

Boomerang 850 user manual

Weslo Momentum Ct5.8 Elliptical Manual Del Usuario

Weslo

Weslo Momentum Ct5.8 Elliptical Manual Del Usuario

Precor EFX EFX 5.23 user manual

Precor

Precor EFX EFX 5.23 user manual

Hammer SPEED RACER S manual

Hammer

Hammer SPEED RACER S manual

Insportline SM-3276 user manual

Insportline

Insportline SM-3276 user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.