Vision Fitness X70 User manual

PINK BAG
HARDWARE INCLUDED
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2008 Vision Fitness. All Rights Reserved. 3.08
AG18.52PRD
REV4
Assembly
Guide
X70
COMMERCIAL ELLIPTICAL TRAINERS
BLUE BAG
HARDWARE INCLUDED
20.5x29x1.5t Wavy
Washer Quantity: 2
X70
COMMERCIAL ELLIPTICAL TRAINERS
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your
new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before
completely tightening any ONE bolt or screw.
6mm T-Shaped Wrench
Screwdriver
5mm T-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Power Cord
Console Mast Bracket
Console Mast Cover
Accessory Tray
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
13mm Wrench
10mm T-Shaped Wrench
17mm Wrench
8mm L-Shaped Wrench
ORANGE BAG
M10x70L Socket Head
Cap Screw Quantity: 2
M8x80L Socket Head
Cap Screw Quantity: 1
M8x20L Socket Head Cap
Screw Quantity: 2
M8x10L Socket Head Cap
Screw Quantity: 4
Spacer
Quantity: 4
M8x20L Socket Head Cap
Screw Quantity: 8
M10x50L Hex Socket Head
Cap Screw Quantity: 2
M10x1.25P Nylon
Nut Quantity: 2
BLACK BAG
M5x12L Socket Head
Cap Screw Quantity: 6
5.3x10x1.0t Washer
Quantity: 4
X70_091111.indd 1 11/11/09 9:11 AM

PINK BAG
HARDWARE INCLUDED
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2008 Vision Fitness. All Rights Reserved. 3.08
AG18.52PRD
REV4
Assembly
Guide
X70
COMMERCIAL ELLIPTICAL TRAINERS
BLUE BAG
HARDWARE INCLUDED
20.5x29x1.5t Wavy
Washer Quantity: 2
X70
COMMERCIAL ELLIPTICAL TRAINERS
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your
new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before
completely tightening any ONE bolt or screw.
6mm T-Shaped Wrench
Screwdriver
5mm T-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Power Cord
Console Mast Bracket
Console Mast Cover
Accessory Tray
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
13mm Wrench
10mm T-Shaped Wrench
17mm Wrench
8mm L-Shaped Wrench
ORANGE BAG
M10x70L Socket Head
Cap Screw Quantity: 2
M8x80L Socket Head
Cap Screw Quantity: 1
M8x20L Socket Head Cap
Screw Quantity: 2
M8x10L Socket Head Cap
Screw Quantity: 4
Spacer
Quantity: 4
M8x20L Socket Head Cap
Screw Quantity: 8
M10x50L Hex Socket Head
Cap Screw Quantity: 2
M10x1.25P Nylon
Nut Quantity: 2
BLACK BAG
M5x12L Socket Head
Cap Screw Quantity: 6
5.3x10x1.0t Washer
Quantity: 4
X70_091111.indd 1 11/11/09 9:11 AM

4
STEP
5
STEP
• Remove the four mounting screws
from the back of the console. Remove
the four console back cover screws.
Connect the wire harness and heart rate
wires that come from the console mast
into the plugs located in the back of the
console. Attach the console to the mast
with the four screws removed earlier.
• Plug in the 9-volt battery. Re-attach
the console back cover with the four
screws previously removed.
• Attach accessory tray to the console
mast with the two included screws and
screwdriver. Insert the water bottle.
CONSOLE
Link Arm
Cover
Dual-Action
End Cap
Dual-Action
Arm
Rotation Housing
3
STEP
5
STEP
3
STEP
• Connect the right dual-action arm to
the right console mast rotation hous-
ing, being sure to line up the holes.
Secure the dual-action arm in place
with four screws (M8x20L) and tighten
with the 6mm T-handled wrench.
Snap the dual-action end cap into
place.
• Make sure the spacers are inserted
into the outside holes of the ball and
socket joint of the lower link arm.
Connect the right lower link arm to the
right dual-action arm by lining up the
holes on the end of each arm. Slide
the screw (M10x50L) through the
hole. Place a nut (M10) on the screw
and tighten using the 17mm socket
wrench and 6mm T-handled wrench.
PINK BAG
Pedal Arm
Lower Link Arm
2
STEP
2
STEP
• Place a wavy washer (M20) on the
axle located under the foot plate of
the right lower link arm.
• Slide the axle of the lower link arm
into the bracket located on the top of
the right pedal arm. Secure the lower
link arm to the pedal arm by attaching
the pedal support bracket and screw
(M8x20L) to the end of the axle.
Secure the outside holes in the bracket
to the footplate with two sockethead
capscrews (M8x10L). Tighten screws
with the 5mm T-handled wrench.
• Repeat the same steps on the left
side
BLUE BAG
1
STEP
• Place the console mast boot on the
end of the console mast.
• Connect the wire tie that exits the
bottom of the console mast to the wire
harness that sits in the bracket at the
top of the frame. Pull the wire tie and
wire harness up through the console
mast while at the same time insert-
ing the console mast into the frame
bracket.
• Secure the console mast to the
frame with two capscrews (M10 x
70L). Tighten with the 8mm L-shaped
wrench.
• Stabilize the console mast by insert-
ing the socket head screw (M8x80L) to
the front of the bracket. Tighten with the
8mm L-shaped wrench.
• Slide the console mast boot down
the console mast and snap it in place
so it integrates with the side covers.
ORANGE BAG
1
STEP
Bracket
Console Mast Boot
Console Mast
Accessory Tray
Console Console Back Cover
• Position the link arm cover over the
joint of the lower link arm and dual-
action arm. With a screw (M5x12L)
and the screwdriver, connect the two
halves of the cover through the hole
located in the front of the cover.
Attach the cover to each side of the
lower link arm with the two washers
(M5) and two screws (M5x12L).
• Repeat these same steps on
the leftside.
BLACK BAG
4
STEP
X70_091111.indd 2 11/11/09 9:11 AM