VISIONARY DESIGNS RE-1067 Manual

© 2020
Locked layer contains
placeholder marks.
Top View
Perspective View
Scale: 19
10’
10’
RE-1067 General Layout
If
SETUP INSTRUCTIONS

© 2020
Locked layer contains
placeholder marks.
= 1 sq foot
Grid View

© 2020
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2020
Step 1 of 4
Locked layer contains
placeholder marks.
Completed Assembly
6
6
6
5A
7
5A
5
Door
Infill
Infill
1
4
3
2
5
PR37
S40
Velcro
TOP VIEW
PR37 S40
Velcro
TOP VIEW
PR37 S40
Velcro
TOP VIEW
PR37
S40
Velcro
TOP VIEW
Velcro: Bottom
Inside Edge
Velcro: Bottom
Inside Edge
Velcro: Top
Inside Edge
Velcro: Top
Inside Edge
Steps:
1) Attach horizontals [5] and [5A] between verticals [1] and [2],
making sure Velcro is facing inward.
2) Attach horizontals [6] between verticals [2] [3] and [1] [4], with
infills between, as shown.
3) Attach horizontal [7] between [3] and [4].
4) Connect Door Threshold between verticals [2] and [3].
See Door Threshold Attachment detail.
5) Connect Door between verticals [2] and [3]. See Door Connection detail.
Item
1
2
3
4
5,5A
6
7
Qty.
1
1
1
1
2,2
4
1
Description
95” S40 Vertical Extrusion w/ PR37
95” S40 Vertical Extrusion w/ PR37 w/ Door Hinge
95” S40 Vertical Extrusion w/ PR37 w/ Door Stop
95” S40 Vertical Extrusion w/ PR37
45” Z45 Horizontal Extrusion
21.833” Z45 Horizontal Extrusion
45” Z140 Horizontal Extrusion
Keep PR37 attached to extrusions [1] [2] [3] and [4], when packing.
Threshold
Door
Threshold
Tighten
setscrew
to secure.
Slide connector
into groove
of extrusion.
Door Threshold
Attachment
*
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
*
*
6
Closet Assembly

© 2020
Step 2 of 4
Locked layer contains
placeholder marks.
11
11
8
Bolt Bolt
8
10
9
Item
8
9
10
11
--
Qty.
1
1
2
2
2
Description
95” S40 Vertical Extrusion w/ PR37
95” S40 Vertical Extrusion w/ PR37
22” Z45 Horizontal Extrusion
Base Plate
18.75”w x 84”h Panel
Steps:
1) Attach base plates [8] to verticals [9] and [10], using bolts.
2) Attach horizontals [11] between verticals [9] and [10],
making sure Velcro is facing toward back.
3) Attach panels to clamps, as shown. See Clamp Attachment detail.
4) Connect fabric graphics to Velcro inside closet and back of backwall.
Panel Panel
Fabric Graphic
Fabric Graphic
Fabric Graphic
Keep PR37 attached to extrusions [8] and [9], when packing.
Velcro: Bottom
Back Edge
Velcro: Top
Back Edge
Keep A10 clamps attached to [2A] [2B] [3C] and [3D], when packing.
PR37
S40
Velcro
TOP VIEW
PR37 S40
Velcro
TOP VIEW
1) Slide clamp into groove
of extrusion.
2) Tighten set screw to
secure clamp.
3) Insert panel into clamp.
4) Tighten knob to secure
panel in place.
Clamp Attachment
Panel
1
2
3
4
Backwall Assembly

© 2020
Step 3 of 4
Locked layer contains
placeholder marks.
Monitor
Mount 10
97
5A 11
Shelf
Shelf
Steps:
1) Attach lights to horizontals [5A] and [11]. See Light Attachment detail.
2) Attach monitor mount to horizontal [7]. See Monitor Mount Attachment detail.
3) Attach shelves to verticals [9] and [10]. See Shelf Attachment detail.
*
**
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Attachment
Clip
Light
Horizontal Extrusion
Shelf Attachment
Horizontal extrusion stays attached to shelf.
Insert lock on horizontal extrusion
into groove of vertical extrusion,
then tighten set screw.
Lock
Set Screw
Back of Shelf
*
Set screws will face
outward for ease
of assembly.
Monitor
Mount
Wing
Nuts
Horizontal
Extrusion
Attach monitor mount to horizontal extrusion,
using bolts and wing nuts.
*Monitor Mount Attachment
Bolts
*
*
*
*
Attachments

© 2020
Step 4 of 4
*
Completed Assembly
Front View Back View
Steps:
1) Assemble panels and connectors in numerical order,
making sure Velcro is facing inward.
2) Connect shelf supports to Velcro.
3) Place shelf on top of shelf supports.
4) Lock counter top to panels [4] and [8]. See Counter Top Lock detail.
5) Attach graphic to panel [6], using standoffs and caps.
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
1
1
1
Description
38”h LT Connector
30”w x 38”h LT Panel w/ Door
38”h LT Connector
19”w x 38”h LT Panel
38”h LT Connector
30”w x 38”h LT Panel
38”h LT Connector
19”w x 38”h LT Panel
1
12
6
Door
Shelf
Support
Door
Standoff
Cap
3
75
4 8
2
3
4
5
6
7
8
Counter Top
Shelf
Graphic
Top View
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock
12
*
Pin
Hole
*
LTC-130 Counter