VISIONARY DESIGNS MOD-1701 User manual

© 2018
Order #XXXXX
Steps:
1) Connect horizontals [1,1A] between verticals [2,2A],
sliding Infill between verticals.
See CEI-110 Corner Connection detail.
2) Attach horizontal [5] between verticals [2A,4], sliding
Infill between verticals, then secure with horizontal [5A].
3) Attach horizontal [6] between verticals [2,3], sliding
Infill between verticals, then secure with horizontal [6A].
4) Attach horizontals [7,7A] between verticals [3,4].
5) Connect Door to vertical [3]. See Door Connection detail.
6) Connect shelf supports to Velcro on inside of Infills,
place Shelf on top of supports.
7) Place Counter Top on top of assembled Counter base.
8) Attach lights and transformer. See Light details.
9) Install SEG Graphic to front of assembled light frame.
See SEG Graphic Installation detail.
Item
1,1A
2,2A
3
4
5,5A
6,6A
7,7A
Qty.
1,1
1,1
1
1
1,1
1,1
1,1
Description
22.1654”w CEI110 Horizontal Extrusion
38”h CEI110 Vertical Extrusion w/ attached S10
38”h S44 Vertical Extrusion w/ Door Hinge
38”h S44 Vertical Extrusion w/ Door Stop
18”w Z45 Horizontal Extrusion
18”w Z45 Horizontal Extrusion
18.5”w Z45 Horizontal Extrusion
Completed Assembly
Counter Top
Shelf
shelf suppoprt
shelf suppoprt
shelf suppoprt
shelf suppoprt
Back View
1
1A
2
5
3
6
4
7A
7
5A
2A 2
2A
I
nfi
l
l
D
o
o
r
I
nf
i
ll
I
nf
i
ll
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Connection
*
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
6A
*
*
CEI-110 Corner Connection
*
1) Insert TSRV2 and A1 Brackets
into grooves of Extrusion.
2) Slide connecting Extrusion over
exposed ends of brackets.
3) Use Set screws to secure
Extrusions.
TSRV2
Bracket
A1
Set
Screw
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
48W / 2A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 5 lights per transformer.
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
MOD-1701 Backlit Counter

© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information