VISIONARY DESIGNS VK-1327 Manual

© 2015
www.classicexhibits.com
Order #XXXXX - VK-1327
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at
[email protected]
Plan View
Elevation View

© 2015
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2015
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.



While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 1 of 3
Backwall Assembly
When assembled
Infill
Infill Infill
Infill
Infill
Item
1
2A/2B
3
4A/4B
5
6A/6B
7
8A/8B
9
10A/10B
11
Qty.
1
1/1
1
1/1
1
1/1
1
1/1
1
1/1
1
Description
96” Vertical Extrusion
39” Horizontal Extrusion
96” Vertical Extrusion
23.5” Horizontal Extrusion
96” Vertical Extrusion
8.5” Horizontal Extrusion
96” Vertical Extrusion
39” Horizontal Extrusion
96” Vertical Extrusion
8.5” Horizontal Extrusion
96” Vertical Extrusion
Steps:
1) Connect Horizontals to Verticals in numerical order, including Infills.
12A
3
4A
5
6A
6B
7
8A 9
8B
4B
2B
10A
10B
11

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 2 of 3
Shelves & Attachments
3
5
7
9
12A 12B
13A 13B
13C
13D
Ceiling B
Shelves
Countertop
Counter Baseplate
Shelves
Infill
Infill
Ceiling A
When assembled
Item
12A/12B
13A/13B/13C/13D
Qty.
1/1
1/1/1/1
Description
38.7556” Vertical Extrusion
Ceiling Support Brackets
Steps:
1) Connect Verticals [12A, 12B] between Counter Baseplate and Countertop.
2) Attach Counter assembly to Verticals [5, 7].
3) Attach Ceiling Support Brackets [13A, 13B, 13C, 13D] to Verticals [3, 5, 7, 9]
as shown.
4) Attach Ceiling A to Ceiling Support Brackets [13A, 13B].
5) Attach Ceiling B to Ceiling Support Brackets [13C, 13D].
6) Connect Shelves to Verticals [5, 7, 9] as shown.
7) Connect Infills to Vertical [1] using A10 clamps.
2) Tighten set screw to
secure A10 to extrusion.
1) Slide A10 connector
into groove of extrusion.
A10 Clamp Detail
Wing
4) Tighten knob to secure
wing in place.
3) Insert Infill into Clamp
1
2
3
4

© 2015
www.classicexhibits.com
Order #XXXXX -
Step 3 of 3
Counter Assembly
When assembled
Steps:
1) Connect legs to bottom of pedestal.
2) Connect countertop to top of pedestal with standoffs and standoff caps.
3) Connect front graphic to front of pedestal with standoffs and standoff caps.