VISIONARY DESIGNS VK-1959 User manual

© 2016
www.classicexhibits.com
Order #XXXXX - VK-1959 Backwall Assembly
1
1
22A
3
4
4A
5
5A
3A
Power Break
Item
1
2/2A
3/3A
4/4A
5/5A
Qty.
2
1/1
1/1
1/1
1/1
Description
Base Plate
42”w Horizontal Extrusion
42”w Horizontal Extrusion
43.141”h Vertical Extrusion
43.141”h Vertical Extrusion
Transformer
Power
Power
*
*
**
Steps:
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of the blunt ends of extrusions
so that two of the set screws are inside groove;
tighten the two set screws to secure.
2) Slide connecting extrusion over exposed end
of bracket; tighten the two remaining set screw
to secure extrusions.
3) Attach base plates [1] to horizontal assembly [2/2A].
Use bolts, washers, and hex nuts.
4) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of horizontals [2 & 2A] and [3 & 3A]
so that two set screws are inside groove;
tighten the two set screws to secure.
5) Slide two A1 L-Brackets into outer interior
grooves of upper and lower horizontal assemblies;
secure with set screws.
6) Slide vertical extrusion assemblies [4/4A] and [5/5A] over
exposed ends of brackets in lower horizontal assembly [2/2A];
tighten set screws.
7) Slide exposed ends of installed brackets of
upper horizontal assembly [3/3A] into open ends of verticals;
secure with set screws.
8) Connect lighting power cords as indicated and
attach transformers.
See Light to Light Connections &
Light to Transformer detail.
9) Apply SEG Graphics to both sides of assembled frames.
See SEG Graphic Installation in General Information.
TS VR 2
Upper
Horizontal A1
A1
Lower
Horizontal
TS VR 2
A1
A1
TS VR 4
Bracket
Set
Screw
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Graphic: To Ensure Proper Fit
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
+
-
Power
Female
Transformer
Light to Tranformer Attachment
++
--
Lights
Male
Light to Light Attachment

© 2016
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information