VISIONARY DESIGNS VK-2979 Manual

© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2979 - 10’x20’ Hybrid Display
Plan View
Perspective View
10’
20’

© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
www.classicexhibits.com
Order #XXXXX
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
4
13
2
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2017
www.classicexhibits.com
Order #XXXXX Crate Packing
Crate 1 of 1

© 2017
www.classicexhibits.com Step 1 of 9
Order #XXXXX Closet Assembly
When assembled
Velcro
1
6
10
10
5
8
4
11
11
9
3
8
8A
2
7
7A
9A
8A
Door
Shelf
Threshold
Infill
Infill
Item
1
2
3
4
5
6
7/7A
8/8A
9/9A
10
11
Qty.
1
1
1
1
1
1
1/1
2/2
1/1
2
2
Description
92”h S44 Vertical Extrusion
92”h S44 Vertical Extrusion
92”h S44 Vertical Extrusion
92”h S44 Vertical Extrusion
92”h S44 Vertical Extrusion
92”h S44 Vertical Extrusion
28”w Z45 Horizontal Extrusion
40.088” Z45 Curved Horzontal
28”w Z45 Horizontal Extrusion
28”w Z45 Horizontal Extrusion
10“w Z32 Horizontal Extrusion
Steps:
1) Attach horizontals [7] & [7A] to verticals [1] & [2] with infill
in between horizontals as shown.
2) Attach horizontals [8] & [8A] between verticals [2] & [3].
3) Attach horizontals [9] & [9A] between verticals [3] & [4].
4) Attach horizontals [8] & [8A] between verticals [4] & [5].
5) Connect horizontals [10] between verticals [5] & [6] with
infill inserted inbetween the two extrusions as shown.
6) Install door threshold between verticals [5] & [6].
7) Install door between verticals [5] & [6] using hinges on
door and vertical [5].
See Door Attachment detail.
NOTE: door swings towards inside of frame.
8) Apply graphics to Velcro located on inside of frame.
9) Connect Assembled shelf to back of verticals [3] & [4].
See Shelf Attachment detail.
Align hole with pin Rotate pin. Spring
will push pin into hole.
Shelf Attachment
12
*
14 1 4
*
*
Door Attachment
*
*
*
*
*
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door
Hinge
Hinge
Door Threshold
Tighten setscrew
to secure
Slide Connector
into Groove
of Extrusion
Velcro on back
of frame.

© 2017
www.classicexhibits.com Step 2 of 9
Order #XXXXX Closet Assembly (cont’d)
12
12A
6
1
13A
14
13
Item
12/12A
13/13A
14
Qty.
1/1
1/1
1
Description
92”w TSP46 Vertical Extrusion
96.5532”w TSP46 Curved Horizontal Extrusion
88.417”h Z32 Vertical Extrusion
Steps:
1) Attach horizontal [13] between verticals [12] & [12A].
2) Connect horizontal [13A] between verticals [12] & [12A].
See TSV1 Lock detail
3) Attach vertical [14] between horizontals [13] & [13A].
4) Install assembled frame between verticals [1] & [6].
*
TSP46
*
*
*
*
Lock
Tighten setscrew
to secure extrusions
TSV1 Lock Detail

© 2017
www.classicexhibits.com Step 3 of 9
Order #XXXXX Closet SEG Graphic
Steps:
1 Install SEG Graphic to assembled frame as shown.
SEG Graphic
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C

© 2017
www.classicexhibits.com Step 4 of 9
Order #XXXXX Front Frame Assembly
When assembled
15A
15B
16A
16B
17A
17B
18
Item
15A/15B
16A/16B
17A/17B
18
Qty.
1/1
1/1
1/1
1
Description
42” TSP46 Horizontal Extrusion
90” TSP46 Vertical Extrusion
38.417" Z45 Horizontal Extrusion
38.417" Z140 Horizontal Extrusion
Steps:
1) Connect Horizontals [15A, 15B] to Verticals [16A, 16B].
2) Connect Horizontals [17A, 17B, 18] between Verticals [16A, 16B].

© 2017
www.classicexhibits.com Step 5 of 9
Order #XXXXX Ceiling & Front Frame Attachment
When assembled
Steps:
1) Connect Ceilings to assembled lower frame with bolts.
2) Connect Front Frame assembly to assembled frame, including standoffs between the frames.
3) Attach Monitor Mount to Front Frame assembly (see detail).
Monitor Mount Attachment
*
Attach monitor plate to horizontal
bar using bolts & wing nuts.
*

© 2017
www.classicexhibits.com Step 6 of 9
Order #XXXXX Curved Wall Assembly
When assembled
3
19A
20
21
22A
22B
22C
22D
21
20
19B
19C
19D
Item
19A/19B
19C/19D
20
21
22A/22B
22C/22D
Qty.
1/1
1/1
2
2
1/1
1/1
Description
47.4869” Z45 Curved Horizontal
47.4869” Z45 Curved Horizontal
Baseplates
91.75” S44 Vertical Extrusion
82.4817” Z45 Curved Horizontal
82.4817” Z45 Curved Horizontal
Steps:
1) Connect Baseplates [20] to Verticals [21].
2) Connect Horizontals [19A,19B, 19C, 19D] between Verticals [3] of
existing assembly and [21], including Infills as shown.
3) Connect Horizontals [22A, 22B, 22C, 22D], including Infills as shown.

© 2017
www.classicexhibits.com Step 7 of 9
Order #XXXXX Curved Wall Assembly (cont’d)
When assembled
Infill
Infill
Infill
Infill
Item
20
23A/23B
23C
24
25A/25B
25C
Qty.
2
1/1
1
2
1/1
1
Description
Baseplates
63.7801” Z45 Curved Horizontal Extrusion
63.7801” Z41 Curved Horizontal Extrusion
46” S44 Vertical Extrusion
63.7801” Z45 Curved Horizontal Extrusion
63.7801” Z41 Curved Horizontal Extrusion
Steps:
1) Connect Baseplates [20] to Verticals [24].
2) Connect Horizontals [23A, 23B, 23C] between [21] of existing
curved wall, and [24],including Infills as shown.
3) Connect Horizontals [25A, 25B, 25C] between Verticals [24] and
[24], including Infills as shown.
20
20
23A
23B
23C
24
24
25A
25B
25C
21

© 2017
www.classicexhibits.com Step 8 of 9
Order #XXXXX Reception Counter Assembly
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
When assembled
Shelf
Countertop
Top View
Item
1
2
3
4
5
6
7
8
Description
38” 90° Connector
36.9738“ x 38” Curved Panel w/Door
38” 90° Connector
19“w x 38”h Side Panel
38” 90° Connector
44.13“w x 38” Side Panel
38” 90° Connector
19“w x 38”h Side Panel
Steps:
1) Assemble LT Panels in numerical order as shown.
2) Place Shelf into assembled counter.
3) Place Countertop onto assembled counter.
Place countertop
onto frame
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock Detail
Hole for lock
1 2
3 4

© 2017
www.classicexhibits.com Step 9 of 9
Order #XXXXX MOD-1430 Charging Station Table
Underside View
Base
Table Top
Post
Completed Assembly
Steps:
1) Connect Base to Center Post, using bolt.
2) Feed cord, from Table Top, through Center
Post and Base.
3) Connect Table Top to Center Post with
fixed brackets and bolts.