VISIONARY DESIGNS MOD-1702 Manual

© 2019 Order #XXXXX
Front View Back View
Modied MOD-1702 General Layout
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019 Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2019 Order #XXXXX
Corner Connection
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 2
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Assembly
CEI-110 Frame Assembly
CEI110 Profile
CEI110 Frame Assembly

© 2019
Case 1 of 2
Order #XXXXX
Graphics
Setup Hardware
Top View of Each Level
12
Infills
18
17A 17
18A
8
8A
9A 9
11A
11
16 16A
10A
13
10
4 5
Shelf
Shelf
Counter
Top
Level 6 Level 7Level 1 Level 2 Level 3 Level 4 Level 5
Door
7A
1 2
736
Case Packing

© 2019
Case 2 of 2
Order #XXXXX
Counter Top Door
19A
14 15
19
23 25
22
24
20
Top View of Each Level
Level 4 Level 5Level 2Level 1
23A
25A
Level 3
Bracket
w/21A
Bracket
w/21
Case Packing

© 2019
Step 1 of 3
Order #XXXXX
1
7A 8A
9A
10A 16A
16
12 13 14 15
19A
18A
17A
17 18 19
23
44
5
11
11A
Infill
Infill
Infill Infill
Door
Infill Infill
Door
6
9
8
7
10
Completed Assembly
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Connection
*
Steps:
1) Assemble lower horizontals [7] [8] [9] [10] [11] between
verticals [1] [2] [3] [4] [5] [6].
2) Slide Infills between verticals.
3) Secure Infills with upper horizontals [7A] [8A] [9A] [10A] [11A].
4) Connect lower horizontals [16] [17] [18] [19] between verticals
[4] [12] [13] [14] [15].
5) Slide Infills between verticals.
6) Secure Infills with upper horizontals [16A] [17A] [18A] [19A].
7) Connect doors to vertical [3] and [12]. See Door Connection detail.
Item
1
2
3
4
5
6
7,7A
8,8A
9,9A
10,10A
11,11A
Qty.
1
1
1
1
1
1
1,1
1,1
1,1
1,1
1,1
Description
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
8.341” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
21.825” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
12
13
14
15
16,16A
17,17A
18,18A
19,19A
1
1
1
1
1,1
1,1
1,1
1,1
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
4” Z45 Horizontal Extrusion
16.067” Z45 Horizontal Extrusion
4” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
Infill
*
*
*
*
Counter Assembly

© 2019
Step 2 of 3
Order #XXXXX
Completed Assembly
6
15
1
**
*
*
20
20
24
25
25A
21
21
21A
21A
23A
Infill
Infill
23
22
6
Steps:
1) Connect horizontals [23] and [23A] to vertical [22] and
horizontals [25] and [25A] to vertical [24] See CEI110
Frame Assembly sheet for instruction.
2) Attach assembled frames to verticals [1] and [15], as
shown. See Frame to Assembly Attachment detail.
3) Slide Infills into back of assembled CEI110 frames.
4) Connect assembled frames to vertical [20], using
horizontals [21] and [21A] and two brackets.
See Z45 & Bracket Connection detail.
Item
20
21,21A
22
23,23A
24
25,25A
Qty.
1,1
1,1
Description
38.752” TSP2 Vertical Extrusion
3.193” Z31 Horizontal Extrusion
39.5” CEI110 Vertical Extrusion
47.75” CEI110 Horizontal Extrusion
39.5” CEI110 Vertical Extrusion
50.037” CEI110 Horizontal Extrusion
1
1,1
1
1,1
*
*
Frame to Assembly Attachment
Bolt
CEI110
S44
Connector
*
Slide Connector into S44 vertical, then
tighten set screws to secure. Attach
CEI110 vertical to Connector, using bolt.
Slide Connector into Z31 horizontal, then
tighten set screws to secure. Attach Z31
to Bracket, using bolts. Attach bracket to
CEI110 horizontal, using bolts. Slide
vertical [20] into slot of Bracket, then
secure lock of Z31 into vertical [20].
Connector
Z31
CEI110
20
Z31 & Bracket Connection
*
Bracket
Counter Attachments

© 2019
Step 3 of 3
Order #XXXXX
Completed Assembly
Back View
Counter Top Counter Top
Shelf Shelf
Transformer Transformer
Steps:
1) Connect lighting power cords and attach
transformers. See Light to Light Connection
and Light to Transformer Connection details.
2) Place shelves onto pins. See Shelf Pin detail.
3) Place counter top on top of assembed counter base.
See Counter Top Attachment detail.
4) Install SEG graphics to front of assembled frames.
See SEG Graphic Installation detail.
BACK VIEW FRONT VIEW
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
***
**
*
**
SE
G Gra
p
h
i
c
S
E
G
G
raph
ic
Shelf Pin
1) Slide pin into groove
of Vertical Extrusion.
2) Use hex tool to
tighten pin in place.
Pin
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
Light to Light Connection
Light to Tranformer Connection
Counter Attachments (Cont’d)