VISIONARY DESIGNS VK-2934 Manual

© 2016
www.classicexhibits.com
Order #XXXXX -
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2934 - General Layout
Perspective View
20’
10’

© 2016
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.



While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
Case 1 of 5
Case Packing - 1 of 5
Top View of Each Level
Level 1 Level 2
Halogen Lights
Setup Hardware
Wings
11 12 14 13

© 2016
www.classicexhibits.com
Order #XXXXX -
Case 2 of 5
Case Packing - 2 of 5
Top View of Each Level
Level 1
8,7
4 2
1 3
17,18
Base Plate (x2)
Graphics
Monitor Mount
5 6
15,16
Level 2 Level 3 Level 4
Connector
F Conn.
Connectors
Connector

© 2016
www.classicexhibits.com
Order #XXXXX -
Case 3 of 5
Case Packing - 3 of 5
Top View of Each Level
Level 1
Pedestal
Counter
Pedestal
Counter
Pedestal Back
Wall Assembly
Pedestal Door
Wall Assembly
25(x4) Shelf Supports
Level 2 Level 3
Base
Plates
Shelf
Shelf
Level 4

© 2016
www.classicexhibits.com
Order #XXXXX -
Case 4 of 5
Case Packing - 4 of 5
Pedestal Back
Wall Assembly
Infills Infills
Pedestal Door
Wall Assembly
25(x4) Shelf Supports
Top View of Each Level
Level 1 Level 2 Level 3
Graphic
Setup Hardware
Halogen Lights
Monitor
Mount
Monitor
Mount

© 2016
www.classicexhibits.com
Order #XXXXX -
Case 5 of 5
Case Packing - 5 of 5
Top View of Each Level
31,32 35,36 33,34
Level 2 Level 3
26 29 27 28
Level 1
Wings

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 1 of 7
Backwall Assembly
When assembled
Item
1
2/2A
3/3A
4/4A
5/5A
Qty.
2
1
1
1
1
Description
Base Plate
48”h Round Vertical Extrusion
48”h Round Vertical Extrusion
41.7083” Curved Horizontal Extrusion
41.7083” Curved Horizontal Extrusion
Steps:
1) Attach base plates [1] to lower verticals
[2] & [3] using bolts as shown.
2) Connect verticals [2] & [2A] together;
repeat step to assembled [3] & [3A].
3) Connect horizontals [4] & [4A] together;
repeat step to assemble [5] & [5A].
4) Attach horizontals [4/4A] & [5/5A]
between verticals [2/2A] & [3/3A].
5) Install A10 clips to verticals [2/2A] where indicated.
See A10 Clamp Attachment detail.
2
3
2A
3A
1
1
44A
5A
5
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Attach graphic
to velcro on back of
assembled frame

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 2 of 7
SEG Frame Assembly
When assembled
SEG Graphic
Blocker
Velcro
Front View
Item
6
7
8
9
10/10A
11/11A
12
13
Qty.
1
1
1
1
1
1
1
1
Description
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
48”h Curved Vertical Extrusion
38.5”w Horizontal Extrusion
38.5”w Horizontal Extrusion
46.2573"w Horizontal Extrusion
48"w Horizontal Extrusion
Steps:
1) Assembled SEG frame pieces together
as shown. Refer to detail.
See Straight Connection detail. 7
6
9
8
10 10A
11 11A
12
13
TSP46
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
**** See attached SEG graphic
installation for graphic attachment
Velcro attached
to back of SEG
extrusion for lights
TSP46
Insert PR53 Spline into
extrusion; secure with
set screws
Straight Connection
*
PR53
*
**
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 3 of 7
SEG Frame to Backwall Assembly
When assembled
Item
14
15
Qty.
2
2
Description
Standoff Block
Standoff Block
15
14
Steps:
1) Attach assembled SEG frame to backwall
using connectors [14] & [15] as show.
2) Attach lights to velcro on back of SEG frame.
Attach lights to velcro
on back of extrusion
facing the back
Attach lights to velcro
on back of extrusion
facing the back
Attach lights to velcro
on back of extrusion
facing the back
15
14

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 4 of 7
Backwall Attachments
Steps:
1) Connect Light to the upper horizontal of SEG Frame.
See Light Connection detail.
2) Attach Wings to A10 clips on verticals [2/2A].
See Wing Attachment detail.
3) Install Monitor Mount to horizontals [12] & [13].
See Monitor Mount Attachment detail. Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
*
*
*
*
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Plastic
Knob
Wing Attachment
*Attach wall plate to
horizontal bars using
standoffs and wing nuts
Hook monitor brackets over
top of wall plate, then secure
with safety bolts to bottom
of monitor brackets.
Monitor Mount Attachment

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 5 of 7
Backwall Assembly Cont’d
When assembled
Steps:
1) Attach base plates to lower verticals [16] & [17] using bolts as shown.
2) Connect vertical [16A] to vertical [16] together;
repeat step to connect [17] & [17A].
3) Connect curved horizontals [18] & [18A] together;
repeat step to connect [19] & [19A].
4) Attach curved horizontal assemblies [18/18A] & [19/19A]
between verticals [3/3A] & [16/16A].
5) Connect horizontals [20] & [20A] between verticals [16/16A] & [17/17A]
Item
1
16/16A
17/17A
18/18A
19/19A
Qty.
2
1
1
2
2
Description
Base Plate
48”h Round Vertical Extrusion
48”h Round Vertical Extrusion
38” Curved Horizontal Extrusion
38” Curved Horizontal Extrusion
16 17
16A 17A
18A
18
19A
19
3A
3
20
1
1
20A
Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Attach graphic
to velcro on back of
assembled frame

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 6 of 7
Backwall Attachments Cont’d
When assembled
Monitor Mount Attachment
Slide connectors into groove
of extrusion. Tighten setscrew
to secure in place. Attach
monitor mount to connectors
with screws.
Connectors
Monitor
Mount
Steps:
1) Attach Lights to upper horizontals where indicated.
See Light connection detail.
2) Connect Wings to vertical [17/17A] using A10 clips
See A10 Clamp Attachment detail.
3) Install Monitor Mounts to verticals where indicated.
See Monitor Mount Attachment detail.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
***
***
*
*
*
*
*When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 7 of 7
Backwall Counter Assembly
When assembled
Item
21
22
23
24
25/25A
26/26A
23
Door
Infill Infill Infill
HingeHinge HingeHinge
21
24
25
25A
25A
Shelf
Qty.2
Counter
25
22
Qty.
2
2
2
2
8
8
Description
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
42”h Corner Vertical Extrusion
13”w Horizontal Extrusion
10”w Horizontal Extrusion
Steps:
1) Attach lower horizontals between verticals.
2) Attach door to vertical [24]. Refer to Door Attachment detail.
3) Slide infills between verticals as shown.
4) Attach upper horizontals between verticals.
5) Attach shelf supports to inside of assembled pedestal using velcro.
6) Place shelf on top of shelf supports.
7) Place counter on top of assembled pedestal.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
26
26
26A
26A