VISIONARY DESIGNS VK-1032 Manual

© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1032 General Layout
Plan View
10’
10’

© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
www.classicexhibits.com
Order #XXXXX
Crate 1 of 1
Crate Packing
Level 1 Level 2 Level 3 Level 4
Setup Hardware Box
Ceiling
Counter Top
Counter
Top
2
3
Wing
Wings
Sign
Base
Plate
ShelfHeader
Base
Plate
7,8
10,10A
5A,5B
6A,6B
11,11A
5
Setup Hardware
Monitor
Mount
Literature
Holders Graphic
Monitor Mount
Door
Infills
7A,9
4 32

© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 4
Backwall Assembly
Completed Backwall Assembly
Item
1
2
3
4
5
5A/5B
6A/6B
Qty.
1
1
1
1
1
1/1
1/1
Description
Base Plate
84” Vertical Extrusion
84” Vertical Extrusion
84” Vertical Extrusion
35“ Mount Plate
28” Horizontal Extrusion
52” Horizontal Extrusion
1) Slide Connectors into
groove of Extrusions.
Tighten set screws
to secure in place.
2) Connect Mount Plate
[5] to Connectors,
using bolts provided.
5
2
3
Connectors
Connectors
*Mount Plate Attachment
Steps:
1) Attach Vertical Extrusion [4] to Base Plate [1], using bolt.
2) Attach Horizontal Extrusions [5,5A,5B] between Vertical Extrusions [2] and [3].
3) Attach Horizontal Extrusions [6A,6B] between Vertical Extrusions [3] and [4].
4) Attach Mount Plate [5] to Vertical Extrusions [2] and [3].
See Mount Plate Attachment detail.
2
1
5A
5
3
4
5B
6A
6B
Velcro on extrusions
must face to BACK of
assembled Backwall
Connector
Velcro:
Back/Bottom Edge
Velcro:
Back/Top Edge
Velcro
Slide PR37 extrusion into
groove of vertical, then tighten
set screw to secure in place.
PR37
Extrusion
Profile
*PR37 Extrusion Attachment

© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 4
Backwall Counter Assembly
Completed Backwall
Counter Assembly
NOTE:
Vertical Extrusions 7/8 and 7A/9 stay
assembled when packing & shipping.
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Connection
*
*
*
7
7A
9
3
2
10
11
10
8
Door
Infill
Infill
11A
10A
10A
Counter Top
Shelf
Support
Internal Shelf
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
*
*
Steps
1) Attach lower Horizontal Extrusions [10] between Vertical Extrusions [2,7] and [3,7A].
2) Connect lower Curved Horizontal [11] between Verticals [8,9].
4) Connect assembled Door to Vertical Extrusion [9]. See Door Connection detail.
5) Side Infills between Vertical Extrusions [2,7] and [3,7A].
6) Attach upper Horizontal Extrusions [10A] and [11A] between Vertical Extrusions and on top of Infills & Door.
7) Connect Shelf Supports with Velcro to inside of Counter, then set Internal Shelf on top of supports.
8) Place Counter Top on top of assembled Backwall Counter. See Counter Top Attachment detail.
Item Qty Description
7/7A 1/1 38” Vertical Extrusion
8 1 38” 135° Corner Vertical Extrusion w/ Door Stopper
9 1 38” 135° Corner Vertical Extrusion w/ Door Hinges
10/10A 2/2 12.5" Horizontal Extrusion
11/11A 1/1 Curved Horizontal Extrusion

© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 4
Backwall Attachments
Steps
1) Attach assembled Header to Ceiling, using screws and wing nuts.
See Header Attachment detail.
2) Attach Ceiling to top of assembled Backwall, using screws.
3) Attach Wings to A10 Clamps. See A10 Clamp detail.
4) Attach Sign. See Sign Attachment detail.
5) Attach Literature Holders. See Literature Holder Attachment detail.
6) Attach Monitor Mount to [5]. See Monitor Mount Attachment detail.
7) Connect Header Graphic to Velcro on back of assembled Header.
8) Connect SEG Graphic to Velcro on back of assembled Backwall.
Item Qty Description
12 2 5.862” Vertical Extrusion
13 1 80.638” Curved Horizontal Extrusion
14 1 78”w Horizontal Extrusion
NOTE:
Extrusions [12/13/14] stay assembled
when packing and shipping.
Connector
Vertical
[4]
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of Connector to
Literature Holder. Attach flat end of
Connector to Vertical [4]. Tighten
locks to secure.
*
12
12
13
14
5
2
3
4
Ceiling
*
*
*
*
*
*
Header
Monitor Mount Attachment
Attach Monitor Mount to Mount Plate
[5], using bolts and wing nuts.
Wing Nut
Bolt
Monitor
Mount
5
*
*
Screw
Cap
Sign Attachment
Connector
Tighten set screw to
secure A10 to Extrusion.
A10 Clamp
Tighten knob to secure
Wing Panels.
Sign
Slide Connector on back of Standoff
Barrels into groove of Vertical [4]
and twist Standoff to secure. Secure
Graphic to Standoff using Screw Cap.
Standoff
Barrel
Bolt
Header Attachment
*
Ceiling
Panel
Header
Wing Nut

© 2017
www.classicexhibits.com
Order #XXXXX
Step 4 of 4
MOD-1177 Workstation Assembly
Item
1
2
3
Qty.
1
1
1
Steps
1)
Attach Vertical Extrusions [2] and [3] to Base Plate [1], using bolts.
2) Attach Wing to front of Vertical Extrusion [3], using Screw Caps.
3) Attach Counter Top to Vertical Extrusion [3].
4) Attach Monitor Mount to Vertical Extrusion [2], uisng screws.
See Monitor Mount Attachment detail.
5) Attach Sign to Vertical [2], using Stand-off Barrels and Screw Caps.
See Sign Attachment detail.
Description
Base Plate
80” Vertical Extrusion
36” Vertical Extrusion
1
2
3
Screw
Cap
Secure sign to Stand-off
Barrels using Screw Caps.
Sign Attachment
Stand-off
Barrel
Slide Stand-off Barrels
into groove of Vertical
Extrusion.
3
2
Sign
Wing
Counter Top
Stand-off
Barrel
Screw
Cap
Completed Assembly
*
**
Monitor Mount
Slide Connectors into groove
of Vertical extrusion. Tighten
set screws to secure in place.
Attach Monitor Mount back
plate to Connectors, using Bolts.
*
Bolts
Monitor
Mount
Connectors
with Set
Screws