VISIONARY DESIGNS Magellan MOR VK-1078 Manual

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Magellan MOR VK-1078 - General Layout
Plan View
10’
10’

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Part Number
1
2
3
4
5
6a/6b
7a/7b
Qty
2
1
1
1
1
1/1
1/1
Description
Base Plate
47”h Lower Vertical Extrusion
47”h Upper Vertical Extrusion
48.115” Lower Curved Extrusion
48.115” Upper Curved Extrusion
52.476” Horizontal Curved Extrusion
52.476” Horizontal Curved Extrusion
Steps:
1) Attach vertical extrusions to base plates [2 to 1 and 4 to 1].
2) Connect vertical pieces together [2 to 3 and 4 to 5].
3) Connect curved extrusions together [6a to 6b and 7a to 7b].
4) Attach horizontal assembles [6a/6b and 7a/7b] between
Base Plate Attachment
1
1
Connect Vertical Extrusion to
Base Plate by placing lock
into slot and tighten with tool.
2
3
4
5
6a
7b
6b
7a
Connection
Bar
Slide Connection Bar
between Extrusions
and tighten Knobs
to secure.
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of connection bar
with knobs on BACKSIDE of unit.
Rear View of Display
**Do not over tighten Knobs.**
Knob
Knob
Connection
Bar
Connection
Bar
Connection
Bar
Graphic Attachment
Apply graphics to back
of assembled backwall.
Holes for Header Attachment

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Assembly (Cont’d)
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
W
I
N
G
W
I
N
G
Attach Wings to Assembled Frame using A10 Clamps.
Attach Header to Frame using Stand off Caps.
Cap

www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Workstation Assembly
Part Number
8
9
10
11
12
13
Qty
1
1
1
1
1
1
Description
Round Base Plate
47”h Upper Vertical Extrusion
47”h Lower Vertical Extrusion
37.25”h Vertical Extrusion
6”w Horizontal Extrusion
42”w Horizontal Extrusion
Steps:
1) Attach vertical extrusions [9 and 11] to base plate [8] as shown,
see detail D on General Information Page.
2) Attach horizontal extrusion [12] between verticals [9 and 11].
3) Slide counter top on vertical extrusion [9] and set atop vertical
extrusion [11].
4) Connect upper vertical extrusion atop lower extrusion [10].
5) Connect assembled workstation to backwall using horizontal
extrusion [13] as shown.
6) Attach round graphic sign to workstation vertical using stand-offs
and screw caps.
stand off
barrel
Slide stand connector on
back of stand-off barrel
into groove of extrusion
Stand-off Attachment
Flange Plate
Counter Top
8
9
10
11
12
13
Stand-off
Screw Cap

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Case Packing Instruction - Case 1 of 2
Level 1 Level 2
Top View
Level 3
Set of Wings
Lights
Setup Hardware
Base Plates
Extrusion #4
Extrusions # 6a and 7a
Extrusion #5
Extrusions # 2and 3 Extrusions # 6b and 7b

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing Instruction - Case 2 of 2
Level 1 Level 2
Top View
Base Plate
Counter Top
Extrusion #13
Extrusion #12
Extrusion #9, 10 and 11