VISIONARY DESIGNS MOD-1176 User manual

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2010
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1176 - Counter Assembly
Description
42”h Vertical Extrusion
34.7” Curved Vertical Extrusion
4”w Shelf Support
42”h Vertical Extrusion w/ Door HInges
42”h Vertical Extrusion w/ Door Stop
20.6”w Horizontal Extrusion
11.5”w Horizontal Extrusion
Item
1/2
1A/2A
1B/2B
3
4
5
6
Qty.
1/1
1/1
2/2
1
1
4
4
Steps:
1) Attach curve pieces [1A and 2A] to vertical extrusions [1 and 2 ]
using V10 connectors as shown.
2) Connect shelf supports to curve extrusions [2A and 1A] as shown.
3) Connect lower horizontal extrusions [5 and 6] between verticals [1, 2, 3 and 4].
4) Place infills and attach door where indicated.
5) Connect upper horizontal extrusions [5 and 6] between verticals [1, 2, 3 and 4].
6) Velcro shelf supports to inside of assembled base.
7) Please internal shelf atop supports.
8) Set lower tier counters atop curve verticals and secure
to straight verticals using thumbscrews and washers.
9) Set counter top on assembled base.
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
1
2
3
4
2A
6
1A
5
Hinges
Door Stop
6
5
Tighten
Screw
Slide V10 between
grooves of extrusions.
V10 Pressure Screw
V10 Attachment
Use hex key tool to
tighten in place.
Velcro Strip
Shelf Support
Holes
Holes
Holes
Lower Tier Counter Attachment
Use thumbscrews and washers to
secure counter top vertical.
6
5
6
5
Door
Infill: 12”w x 38.918”h
Infill: 12”w x
38.918”h
Front Infill:
12”w x 38.918”h
Internal Shelf
Holes
2B
2B
1B 1B

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2010
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews
NOTE :
PDF copies of your Setup Instructions are available @ classicexhibits.com
See the search tool on the lower left hand corner of the Home page.
Enter the 5 digit Order #.
Search for Setup Instructions
search