Visonic Kp-140 pg2 User manual

D-303015 1

KP-140 PG2/KP-141 PG2

Portable Remote Wireless 2-Way Keypad

User’s Guide

1. INTRODUCTION

KP-140 PG2 and KP-141 PG2 are 2-way PowerG wireless keypads

for the PowerMaster family control panels. The KP-141 PG2 is the

same as the KP-140 PG2 but also includes a built-in proximity RFID

tag reader. Both keypads enable most common everyday user

functions:

•Arm and Disarm the alarm system.

•Initiate Emergency, Fire and Panic alarms.

•Control X-10 devices and PGM output.

•Perform one of the AUX (auxiliary) predefined functions.

•Review system Status.

When authorization is required, for example, to arm or disarm the

system, the user can enter his PIN Code via the built-in numerical

keypad or alternatively present a valid proximity tag to the built-in tag

reader (only with KP-141PG2) located at "N" in Figure 1.

In addition, the KP-140 PG2/KP-141 PG2 keypad supports panels

featuring Partitions. Partitioning allows you to have up to three

controllable areas; each partition can be armed and disarmed

independently regardless of the status of the other two partitions by

the same or different users (see buttons marked "E" in Figure 1).

The keypads can be wall mounted using the supplied bracket or be

used as portable units. For compliance with various international

standards, the keypads are equipped with two tamper switches that

can be configured to detect when the cover of the battery

compartment is removed or when the unit is removed from its

mounting bracket.

Other features of the KP-140 PG2/KP-141 PG2 keypad include:

•Status, alarm memory, trouble and Ready / Not-Ready indications.

•Automatic reporting of low battery voltage.

•Keypad back lighting.

•Exit/entry beeps

•Tag reader can also be used to enroll proximity tags into the panel.

•Long-life 4-5 years battery life expectancy (for typical use), 3 VDC

lithium battery.

A. ARM HOME H. AUX / ENROLLMENT

B. ARM AWAY I. EMERGENCY ALARM

C. DISARM J. FIRE ALARM

D. X-10 / PGM K. PANIC ALARM

E. PARTITION SELECTION L. BUZZER INDICATOR

F. ARM INSTANT M. LED INDICATOR

G. STATUS / ESCAPE N. TAG READER

Figure 1 - External View

2. INSTALLATION

2.1 Mounting and Battery Replacement

1. Drill 2 holes in mounting surface, insert wall anchors and fasten the

bracket with 2 screws.

2. Place the "Visual Indications" sticker within the frame.

3. Slide the keypad into the bracket.

A. Magnet (activates back tamper when bracket is removed from the

wall).

Figure 2 - Mounting

1. Slide out the cover.

2. Replace the battery (verify proper polarity) and close the cover.

A. Battery compartment tamper switch

Figure 3 - Battery Replacement

2 D-303015

2.2. ENROLLMENT

Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "Zone / Devices" option of the Installer Menu a general

description of which is provided in the following flow chart.

Step 1 Step 2 Step 3 Step 4 Step 5 Step 6

Enter the Installer menu

and select the “ZONES /

DEVICES”

Select "ADD NEW

DEVICE" Option

See Note [1]

Enroll the device or Enter

the device ID

Select the desired Zone

Number

Configure Location,

Zone Type &

Chime Parameters

Configure

the

Keypad



@ @

@Means scroll and select

See Note

[2]

Notes:

[1] If the keypad is already enrolled you can configure the keypad parameters via the “Modify Devices” option – see Step 2.

[2] Select the "Device Settings" option and refer to section 2.3 to configure the keypad parameters.

2.3. Configuring the Keypad Parameters

Enter the menu and follow the configuration instructions for the KP-140 PG2/KP-141 PG2 keypad as described in the

following table.

Option Configuration Instructions

Here you determine which of the two tampers (i.e. battery compartment cover and wall tamper) will be active.

Optional settings: Disabled (default); Wall only; Battery only.

•

Here you determine whether or not the control panel will monitor supervision messages sent by the keypad or not (see

Note).

Optional settings: ON (default) or OFF.

Note: Every 5 minutes the keypad performs a communication test session with the control panel (i.e. "Supervision

signal) to check the integrity and quality of the Radio link. If the keypad does not report a supervision signal at

least once within a predefined time window, a “MISSING” trouble alert is initiated. Therefore, if you intend to take

the keypad out of the protected premises you must switch the Supervision OFF to avoid the trouble alert.

•

Here you determine whether the keypad will sound the exit and entry beeps, or not, or whether the keypad will sound the

beeps only when the system is armed AWAY and not when it is armed HOME.

Optional settings: ON; OFF (default) and OFF @ Home.

•

Here you select the function of the (AUX) button . Four options are offered:

Not used: No function assigned to AUX button.

Stop Beeps: Pressing the AUX button will cause the control panel and other devices in the system (such as keypads,

sirens etc.) to stop beeping (for example during exit or entry delays).

Skip exit delay: Pressing the AUX button will immediately stop the exit delay.

PGM: Pressing the AUX button will activate the PGM output. The functions of the PGM output is configured at the

corresponding sections of the control panel’s Installer Guide (see “OUTPUTS” menu) and User Guide (see

“SCHEDULER ” menu).

Optional settings: Not Used (default); Stop Beeps; Skip exit delay; and PGM.

2.4 Enrollment of Proximity Tags

The built-in proximity tag reader of the KP-141PG2 can be also used

to enroll proximity tags into the PowerMaster panel via the keypad as

described in the corresponding section of the control panel's User or

Installer Guide.

When the panel display prompts you to enroll the tag ("ENROLL NOW"

is displayed), perform the following:

a) Press the AWAY button ( ) on the KP-141 PG2 keypad -

the AWAY button begins to blink.

b) Present the proximity tag to the KP-141 PG2 keypad within the

timeout period. If the enrollment is successful the display reads

"DEVICE ENROLLED"and then shows the device details.

UTTON (¿

)

XIT

NTRY Beeps

UPERVISION

AMPERS

DEVICE SETTINGS

Z20.DEV SETTINGS

Z20.SET CHIME

Z20.ZONE TYPE

Z20.LOCATION

ID No. 370-XXXX

Z20: Keypad

ENTR ID:XXX-XXXX

ENROLL NOW or

MODIFY DEVICES

ADD NEW DEVICES

02.ZONES/DEVICES

D-303015 3

3. USING THE KEYPAD

3.1 Arming and Disarming the System

Step Basic Arming User Actions Keypad & Panel Response

1 Select a PARTITION (1)

(when Partition is enabled) or or

The selected button lights.

Arm AWAY

Arm HOME

Disarm (OFF)

The selected button starts blinking and

prompts you to enter your "User Code" or

present your Tag. See step 3.

Quick arm AWAY (2) (≈2 sec.)

Quick arm HOME (2) (≈2 sec.)

Enter USER CODE or present

Proximity TAG. (3) (4) [USER CODE] or [present TAG]

[DURESS CODE] (2580 by default) (5)

The keypad's LED blinks red once to indicate

transmission of the arming command to the

control panel. The control panel's response is

then indicated on the keypad via the LED and

the buzzer – see “Panel Response to

Keypad Commands” section 3.5 below.

INSTANT (After arming HOME/ AWAY) (6) (8)

4LATCHKEY (After arming AWAY) (7) (8)

The keypad's LED blinks red once to indicate

transmission of the command to the control

panel. The control panel's response is then

indicated on the keypad via the LED and the

buzzer – see “Panel Response to Keypad

Commands” in section 3.5 below.

Notes:

1. If Partition is disabled at the control panel, skip Step 1.

2. The Quick arm functions only if enabled at the control panel.

3. If Quick arm is selected in Step 2, skip Step 3.

4. (a) Pressing a non-valid code causes the control panel to reject the transmission.

(b) If the action is not completed while the selected arming button is blinking, the desired function will not be executed.

5. To use the Duress Code refer to the respective section in the control panel’s User Guide.

6. Press the INSTANT button within maximum 8 seconds timeout period after completing the previous step. This will delete the entry delay for

the current arming session.

7. Press the AWAY button TWICE within maximum 8 seconds timeout period after completing the previous step. To use the LATCHKEY arming

refer to the respective section in the control panel’s User Guide.

8. You can perform the LATCHKEY and INSTANT functions, one after the other. The order is not important.

3.2 Automation

The functions of the PGM and X-10 outputs is configured at the corresponding sections of the control panel’s Installer Guide (see “OUTPUTS”

menu) and User Guide (see “SCHEDULER ” menu).

Output Function Actions Response

X-10 or PGM device ON [PGM J00]or [X-10J01 to 15]

X-10 or PGM device OFF [PGM J00]or [X-10J01 to 15]

X-10 or PGM device TOGGLE [PGM J00]or [X-10J01 to 15]

The keypad's LED blinks red once to

indicate transmission of the

command to the control panel. The

control panel's response is indicated

on the keypad via the LED and the

buzzer – see “Panel Response to

Keypad Commands” in section 3.5

below.

3.3 Initiating Alarms

Alarm Actions Response

Emergency

alarm (≈2 sec.) See section 3.5.

Fire alarm (≈2 sec.) See section 3.5.

Panic alarm (≈2 sec.)

See section 3.5.

3.4 Other Functions

Function User Actions Response

AUX Function (1) See section 3.5.

Notes:

1. The function of the AUX button is configured in section 2.3 above

3.5 Panel Response to Keypad

Commands

When executing a command, the keypad's LED ("M" in Figure 1)

blinks red once to indicate transmission of the command to the

control panel. If the operation is successfully completed, the green

LED lights momentarily and a "happy tune" is heard. If the operation

fails or cannot be completed, for example, when the system is "not

ready", the red LED lights steadily and a "sad tune" is heard. If a

trouble or alarm memory condition exists in the system, or when the

system is not-ready to arm, the Status button (G in Figure 1) flashes

for several seconds prompting you to press it to retrieve the status

information from the control panel.

4 D-303015

Panel Response Buzzer Indication LED Indication Problem Indication

Success: Operation is

successfully completed

Happy (success) beep Momentary GREEN

Fail: Operation failed Sad (failure) beep Momentary RED

No communication: Control

panel does not respond. None None

If the panel is Not-Ready or if a Trouble or

Alarm Memory conditions exit, the Status

button (G in Fig.1) flashes for few seconds.

To identify the reason, press the button to

retrieve the Status indication - refer to section

3.6 for further information.

3.6 Retrieving and Displaying System Status

Step Status

Request User Actions

Keypad &

Panel

Response

1 Request

Status

The keypad's LED

blinks red once to

indicate

transmission of the

status request to the

control panel.

2 Look at

status / /

The panel's status is

indicated on the

keypad via the LED

and the Arming

Keys and Partition

Keys – see below

Arming Status

The system Arming Status is indicated via the respective

arming/disarming buttons' LED that light for several seconds. For

example, if the system is armed AWAY, the button will light and if

the system is disarmed, the button will also light.

If Partition is enabled, the arming Status of the first partition is

displayed concurrently with the corresponding first partition button

LED ,then the second partition Status is displayed

concurrently with the second partition button LED and then the

third partition Status is similarly displayed.

Indication of Ready/Not Ready & Trouble Status

The Ready/Not Ready, Alarm Memory and Trouble indications are

provided via the keypad LED (see "M" in Figure 1) as follows:

LED

Indication

[1]

System

Status [2] What it Means

Green System

READY You can arm the system

Red System NOT-

READY One of the zones is not secured.

You can not arm the system before

the zone is secured or bypassed. [3]

Yellow Trouble or

Alarm

Memory

There was an alarm or there is

trouble situation that need to be

reviewed and cleared. [3]

Yellow

blinking Keypad Low-

Battery The battery of the keypad must be

replaced as shown in section 2.1.

[1] The LED indication is displayed after the first red blink indicating

the status request.

[2] If there is more than one status indication, the LED will display

them consecutively.

[3] See respective sections in the control panel's User and Installer's

Guides.

APPENDIX: SPECIFICATIONS

Frequency Band (MHz) Europe: 433, 868, USA: 915

Communication Protocol PowerG

Battery type 3V, CR123A type.

Caution!

Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to

manufacturer's instructions.

Battery Life Expectancy 4-5 years (for typical use).

Operating Temperature 0°C to 49°C (32°F to 120°F)

Dimensions (LxWxD) 127x70x24mm (5 x 2-3/4 x 31/32 in)

Weight (including battery) 107g (3.4 oz)

Color White

Compliance with Standards Europe: EN 300220-1, EN 50130-4, EN 50131-1 Grade 2 Class II, EN 50131-3, EN 301489.

USA: CFR 47 part 15, Canada RSS 210

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not

returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2002/96/EC Waste Electrical and Electronic Equipment.