Visonic Mkp-150 User manual

DE2462U 1

MKP-150, MKP-151

2-Way Wireless Keypad User's Guide

1. INTRODUCTION

NOTE: RELEVANT TO POWERMAX+ VERSION B AND ABOVE

The MKP-150 / MKP-151 (different color) operates using two-way

encrypted coded transmission and provides aural and visual

indications. For each PowerMax+ control panel, a maximum of

two MKP-150/MKP-151 keypad devices may be enrolled.

The MKP-150/MKP-151 may be operated either by AC power

supply or by battery power. If AC power is used, the device

operates continuously and the system status is constantly

updated. If powered by batteries, the keypad enters sleep mode

15 sec after last key press. The keypad immediately becomes

operational again upon pressing of any key.

Note: In the event of an AC power failure, the MKP-150/MKP-151

operates on batteries as described above.

The device enables the user to arm/disarm the alarm system, to

initiate emergency/fire/panic alarms and to turn lighting devices

on and off.

The main features of the MKP-150/MKP-151 are:

•Status, alarmmemory, and trouble dataretrievalfromPowerMax+.

•Automatic reporting to PowerMax+ of low battery voltage, AC

failure, tamper.

•Visual indications by red/green/amber LED and LCD display.

•Keypad and LCD backlighting activation.

•Light dim / brightness

•Various audible signals sounded by the speaker in response to

specific actions.

•Automatic supervision messages.

•Diagnostic test of PowerMax+.

•Two long-life 3 Volt Lithium batteries.

•Wall mounting.

•Friendly programming.

The Power (green) LED lights when operated using AC power. The

Trouble (amber) LED lights if a "trouble" state is currently detected

within the PowerMax+. The Chime (green) LED lights when the

chime function is active. The Arm (red) LED lights when the

system is in armed state (away mode), or flashes (home mode).

A periodic supervision message is transmitted, at regular intervals,

from the MKP-150/MKP-151 to the PowerMax+ control panel. This

ensures active participation of the MKP-150/MKP-151 in the

system.

Operating power is obtained from two 3 Volt Lithium batteries, or

by AC. A weak battery causes a "low battery" message to be sent

to the PowerMax+.

A Screen Saver appears on the display (if enabled by the installer

on the PowerMax+ unit) when no key is pressed for more than 30

seconds. The display reads “POWERMAX” and the LEDs do not

light (to prevent an intruder of knowing the system status). The

normal display returns after pressing the OFF button followed by

entering user code (Refresh by Code) or after pressing any key

(Refresh by Key), depending on the PowerMax+ settings of the

installer. If Refresh by Key was selected, the first key press (except

for Fire and Emergency) causes the normal display to return while a

second press performs the key function. In the case of the Fire and

Emergency keys, the first key press causes the normal display to

return and also performs the Fire/Emergency function.

AWAY

MICROPHONE

PLAY MESSAGE

VOLUME UP /

LIGHT BRIGHT

VOLUME DOWN /

LIGHT DIM

CHIME ON/OFF

MUTE SPEAKER

NO ENTRY DELAY

RECORD MESSAGE

LIGHT OFF

TESTING

ARMING

“AWAY”

ARMING “HOME”

DISARMING

BYPASS

LIGHT ON

EMERGENCY

(Hold for 2 sec.)

FIRE

PANIC

(press both buttons)

“SHOW / OK”

BUTTON

“ESCAPE”

BUTTON

“NEXT”

BUTTON

LCD

WINDOW

“BACK”

BUTTON

SPEAKER

AWAY

Figure 1: External View

2 DE2462U

2. SPECIFICATIONS

ELECTRICAL

Battery Power Source: Two 3 Volt Lithium batteries, type

CR123A (Sanyo or equivalent).

Battery Life Expectancy: 2 years (for typical use).

AC Power Supply (optional): Plug-in transformer.

120 VAC, 60 Hz / 9 VAC, 0.35 A min. (in the U.S.A.)

230 VAC, 50 Hz / 9 VAC, 0.35 A min.

UL installation: Use transformer type OH-35048AT,

manufactured by Oriental Hero Electrical Factory.

In Europe and elsewhere: Use only Safety National Approved

AC adapter, mains-to-9 VAC, 0.35 A min.

AC Current Drain: Approx. 30 mA standby, 300 mA max. at full

load.

Display: Single line, backlighted 16-character LCD and 4 LED

indicators.

Control Functions: Home Arming, Away Arming, Bypass,

Disarming, Latchkey, Light ON / OFF, Light Dim / Brightness,

Recording, Forced Arming, Panic, Fire and Emergency calls.

Sleep Mode: Used to minimize current consumption. The unit

enters sleep mode 15 seconds after last use (applies only when

using batteries or when there is a power failure).

Supervision: A periodic supervision message (programmable) is

transmitted automatically once every 15 minutes (Europe), once

every 60 minutes (USA), or according to the local standards. This

function can be disabled.

Panic Alarm Message: Activated by simultaneously pressing the

and keys.

Tamper Switch: Normally closed. A tamper signal is transmitted

in three ways: when the MKP-150/MKP-151 case is opened;

when the keypad assembly is separated from the bracket; or if

the MKP-150/MKP-151 unit is ripped from the wall.

Compliance with Standards: FCC part 15, EN 50131-1 Grade 2

Class II, TS 50131-3 and Directive 1999/5/EC

RF SECTION

Operating Frequencies: 315 MHz (in USA & Canada) or other

UHF channels per local requirement in the country of use.

Receiver Type: Super-heterodyne, fixed frequency

Receiver Range: 600 ft (180 m) in open space

Antenna Type: Spatial

Coding: Two-way wireless protocol

ENVIRONMENTAL

For indoor use only.

Operating Temp. Range: 0°C to 49°C (32°F to 120°F)

Storage Temp. Range: -20°C to 60°C (-4°F to 140°F)

Humidity: 85% relative humidity, @ 30°C (86°F)

PHYSICAL

Dimensions: 172 x 99 x 39 mm (6 7/8 x 3 15/16 x 1 9/16 in.)

Weight: 375 g. (13 oz)

Mounting: Surface-mounted

Color: Light gray

3. INSTALLTION AND WIRING

Perform the procedures as illustrated in the following Figures.

Note: Mount the unit inside the secured premises, in a location providing optimum signal reception from the PowerMax+ unit, (refer to

Installing Wireless Systems Installation Guide – The Right Way, document no. DE2000W, for further details).

After removing

the screw,

pull down the

bracket fully

Remove

the bracket

Figure 2: Bracket Removal

Mark and drill 4

holes in mounting

surface. Insert wall

anchors and fasten

the bracket to the

mounting surface

with 4 screws.

Screw

Holes

Screw

Hole

IMPORTANT !

The back tamper

switch will not

activate a tamper

alarm unless this

segment is secured

to the wall with

a screw.

Screw

Hole

Note: Leave at least 3 cm (1.25 in.) free space around the

bracket.

Figure 3: Bracket Mounting

ess the tab inwa

and remove the cover

Insert

batteries

(verify proper

polarity) and

close cover

Back

Tamper

Switch

Figure 4: Battery Insertion

VAC

Wiring

Inlets

Connect the 9 VAC

power supply to the

terminal block. Route

the wiring through the

wiring channels.

Note:

The transformer

is optional

Figure 5: Wiring

Match the panel with

the bracket projections.

Pull downward and

secure the bracket with

the locking screw

Figure 6: Panel Mounting

DE2462U 3

4. ENROLLING/DELETING THE KEYPAD FROM THE POWERMAX+ MEMORY

To enroll all the MKP-150/MKP-151 functions (for complete list see PowerMax+ Installer Guide), enter the PowerMax+ Installer Mode

from the PowerMax+ keypad, and proceed as shown in the following illustration.

Note: Refer to PowerMax+

Installer Guide for details on

performing a diagnostic test

(First display is READY

or NOT READY)

READY 00:00

USER SETTINGS

NORMAL MODE

ENTER CODE

1. NEW INSTL CODE

2. ENROLLING

[installer code]

INSTALLER MODE



ENROL WL 2WAY KP

ENROLL WL DEVICEENROLLING TYPE

[KEYPAD No. 1 to 2]

(e.g. 2)

2way kp No :

2way kp No : 2 2way kp No : 2

2way kp No: 2

Enrolling a wireless

Keypad

for next

enrolling action

<OFF> TO DELETE

press back

tamper

switch

once

(see Fig. 4)

TRANSMIT NOW

Deleting a wireless

Keypad

2way kp No: 2

ENROLL KEYFOB

Black rectangle means

that the KEYPAD No. 2

is already enrolled.

AWAY



NEXT



NEXT NEXT NEXT

ENROL WL 1WAY KP NEXT

9. DIAGNOSTICS



Figure 7: Enrolling / Deleting a MKP-150/MKP-151 Device from PowerMax+ Memory

5. DEFINING MKP-150/MKP-151 PARAMETERS

5.1 Installer Menu Functions

Important: All installer settings affect only the specific keypad on

which the settings were performed.

The Installer menu enables you to perform the following

functions:

SUPERVISION

The keypad transmits supervision reports periodically to the

PowerMax+.

The options are: 15 minutes, 1hour and disable.

Note: In FCC installations, the keypad must be set to 1 hour.

PIEZO BEEP

Here you determine whether warning beeps will sound or be

muted during exit and entry delays.

Options: enable beeps, off when home and disable beeps.

BACK LIGHT

The keypad and LCD back light can be activated in one of two ways:

•By key press: back light is activated for ten seconds by a long

press (2 sec) of any key.

•Always on: back light remains on continuously. (Enabled only

when the unit is connected to the AC supply.)

The options are: OFF after 10s and always ON.

JAM DETECTION

Note: This feature is enabled only with PowerMax+ version

3.3.14 and above.

Here you determine whether jamming (interfering transmissions

on the radio channel used by the system) will be detected.

The options are: UL 20/20, EN 30/60, class 6 (30/60), or

disable.

RECORD SPEECH

This mode allows you to record up to 5 custom zone names.

SERIAL NUMBER

Enables reading the system serial number for support purposes only.

5.1.1 To Set Supervision Time

Make sure the system is not in Arm mode.

The installer’s menu is accessible only to those who know the

installer’s code, which is 9Î9Î9Î9by factory default.

A. Press the next button (►) repeatedly until the display reads:

INSTALLER MODE

B. Press the Show / OK button (√). The display should read:

ENTER CODE: ___

Note: For PowerMax+ that has two installer codes, the default

INSTALLER code is 8888 and the default MASTER

INSTALLER code is 9999.

C. Enter the installer code. The display will change to:

SUPERVISION

D. Press <√>.

E. Press <►> repeatedly to select one of the available options.

F. Press <√> to set the selected option.

5.1.2 To Activate the Recording Mode

A. Upon gaining access to the installer menu (see section 5.1.1

A to C), the display will read “SUPERVISION”.

B. Press <►>; RECORD SPEECH is displayed.

C. Press <√>. The display will change to:

USER TERM #1

Note: User Term refers to the name assigned to the recorded

zone.

Note: It is recommended to assign custom names that are

identical to the custom names defined in the PowerMax+.

D. Press the key until this is displayed briefly:

RECORD A MESSAGE

4 DE2462U

Immediately thereafter, the display will change to:

TALK NOW

E. Do not release the key and start talking immediately (for

example, living room or library), while facing the front panel.

The dark square boxes will slowly disappear one by one, from

right to left. When the last one disappears (5 seconds later)

the following message will be displayed:

RECORDING ENDED

F. Release the key. To check the message, press the

key and listen to the playback.

G. Press <►>. The display will change to:

USER TERM #2

H. Repeat the procedure for User Terms #2 - #5 to record the

names of zones 2 - 5.

5.1.3 To Enable/Disable Piezo Beeps

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> twice; PIEZO BEEP is displayed.

C. Press <√>.

D. Press <►> to select between enable beeps, off when home

and disable beeps.

E. Press <√> to set the selected option.

5.1.4 Keypad Back Light

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until BACK LIGHT is displayed.

C. Press <√>.

D. Press <►> to select between OFF after 10s and always ON.

E. Press <√> to set the selected option.

5.1.5 Jam Detection

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until JAM DETECTION is displayed.

C. Press <√>.

D. Press <►> to select between UL 20/20, EN 30/60, class 6

(30/60), disable and other.

E. Press <√> to set the selected option.

5.1.6 To Read the Device Serial Number

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until SERIAL NUMBER is displayed.

C. Press <√> to read the serial number assigned to the unit.

RECORD SPEECH

user term #1



user term #2

user term #3

user term #4

user term #5

READY 00:00

USER SETTING

NORMAL MODE

ENTER CODE

[installer code]

INSTALLER MODE



SUPERVISION

superv time 15m

superv time 1h



disable

PIEZO BEEP

enable beeps

disable beeps



off when home

(*)

In Canada, “disable”

must be selected.

JAM DETECT

UL 20/20



EN 30/60

class 6 (30/60)

disable

SERIAL NUMBER

xxxxxxxxxxxxxxxx



BACK LIGHT

OFF after 10s



always ON

Note: The currently saved options are displayed with

a dark box at the right side of the display.To review

the options, repeatedly click or until the desired

option is displayed, then click (a dark box will

be displayed at the right side).

xxxxxxxxxxxxxxxx

Figure 8: Defining MKP-150/MKP-151 Functions

5.2 User Setting Functions

The user settings on your MKP-150/MKP-151 keypad include the

following functions (for instructions see PowerMax+ User Guide):

•Set Bypass

•Show Bypass

•Recall Bypass

•Set Phone Number

•Set User Codes

•Set Voice Option

•Auto Arm Option

•Auto Arm Time

•Squawk Option

•Light by Timer (for further details, see PowerMax+ User Guide,

Para. 4.5 Automatic ON/OFF Control).

•Light by Sensor (for further details, see PowerMax+ User

Guide, Para. 4.5 Automatic ON/OFF Control).

Make sure the system is not in Arm mode. The display should read:

READY

TO SET FUNCTIONS

The user's menu is accessible only to those who know the master

user code, which is 1Î1Î1Î1by factory default.

Use this code for initial access, and replace it with a new code

known only to you, (see PowerMax+ User's Guide).

A. Press the ►button twice.

The display should read:

USER SETTING

B. Press the √. The display should read:

ENTER CODE: ___

C. Enter your code. The display will change to:

SET BYPASS

Note: If the bypass function is disabled, the display will

change to:

SET PHONE NUMBER

D. Having gained access to the user's menu, you may now select

any other item on the User Settings menu as detailed in

Figure 9.

DE2462U 5

NOTES

(1) Function inside black rectangles are accessible only if master user code was entered.

(2) Press OK to display the number, state and name of first bypassed zone. Press NEXT/BACK repeatedly to view all the bypassed zones.

(3) To enter “A” (AM) press ( or one of the 3 keys above it), to enter “P” (PM) press (or one of the 3 keys above it). (Not

functional if the time format has been set to the 24 hour clock via the PowerMax+.)

(4) SET/SHOW/RECALL BYPASS menus are accessible only if “manual bypass” has been selected by the installer via the PowerMax+.

(5) In the SET VOICE OPTION, if you select “enable prompts”, the PowerMax+ mute speaker button is active.

SHOW BYPASS

RECALL BYPASS

BYPASS LIST

<OK> TO RECALL

(2)

SET BYPASS

NORMAL MODEREADY

<OK> TO BYPASS Z01: BYPASSED

Z01: OPEN

KITCHEN

Alternating

KITCHEN

Alternating

(for checking state of next zone)

ENTER CODE _ _ _ _

INSTALLER MODE

(4)

(4) (example)

SET PHONE NUMBER

)

SET USER CODES user code 1 0 0 0 0

(for next user code 2, 3....8)

[code]

user code 1 user code1

(example)

(1)

AUTO ARM OPTION disable autoarm enable autoarm

(if it is the current option)

)[time]

AUTO ARM TIME arm time _ _: _ _A

SQUAWK OPTION

(1)

SET VOICE OPTION enable prompts

(if it is the current option)

(1)(5)

)[4-digit master/user code]

if not satisfied

)

if not satisfied

)

disable prompts disable prompts

enable autoarm

(First display is READY

or NOT READY)

)

)))

)

))

)

BACK

Moving one level

up in the menu

To move within the menus, the

following keys can be used:

SHOW / OK

squawk disable

sqwk low volume

sqwk mid volume

sqwk hi volume

(To review options, use

NEXT or BACK button)

Tel. No .



1st private tel#

Tel. No .



2nd private tel#

Tel. No.



3rd private tel#

Tel. No.



4th private tel#

)))

LIGHT BY TIMER

LIGHT BY SENSOR

enable disable disable

)

if not satisfied

)

enable disable disable

)

if not satisfied

USER SETTINGS

(1)

(3)

(1)

ESC

Figure 9: User Settings Flow Chart

6. OPERATION

Function Actions

Arming HOME (1) (3)

Arming HOME INSTANT (1)

Arming AWAY

AWAY

(1)

Arming AWAY INSTANT

AWAY

(1)

Forced Arming HOME (1)

Forced Arming AWAY

AWAY

(1)

AWAY

Disarming (1)

X-10 device (1-15) ON unit # [1-15]

X-10 device (1-15) OFF unit # [1-15]

Light dim / brightness unit # [1-15]



6 DE2462U

Emergency alarm (≈2 sec.) (5)

Fire alarm (≈2 sec.) (5)

Panic alarm

Latchkey arming

AWAY

[user code](1)

AWAY AWAY

(2)

Quick arm / HOME /

AWAY

(operates only if enabled in

PowerMax+)

Chime ON/OFF (press again to select

option)

Local Recording (press continuously while

talking)

Playback

Local Voice On / Off

Testing (1) (3)

Bypass (1)

Duress [duress code] (2580 by

default)

Notes

1. The factory default master user code is 1 1 1 1. The code is not

required if quick arming has been permitted by the installer.

2. For LATCHKEY arming function, press the AWAY key, and

then press the AWAY key again.

3. Pressing a non-valid code combination (not master / user

code) causes a long failure beep.

4. If a keying sequence is not completed within a five second

period, the desired function will not be executed.

5. Emergency, Fire or Panic buttons become active only if

enabled in the PowerMax+.

7. COMPLIANCE WITH STANDARDS

This device complies with the essential requirements and provisions of

Directive 1999/5/EC of the European Parliament and of the Council of 9

March 1999 on radio and telecommunications terminal equipment.

Frequency Allocations for Wireless Devices in European

Countries:

•315 MHz is not allowed in any EU member state.

•433.92 MHz has no restriction in any EU member state.

•868.95 MHz (wide band) is allowed in all EU member states.

•869.2625 MHz (narrow band) is not restricted in any EU

member state.

The user is cautioned that changes or modifications to the unit,

not expressly approved by Visonic Ltd., could void the user's FCC

or other authority to operate the equipment.

The 315 MHz model of this device complies with Part 15 of the

FCC Rules and RSS-210 of Industry and Science Canada.

Operation is subject to these two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesirable operation.

The digital circuit of this device had been tested and found to

comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in residential

installations. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio and television reception. However, there is no guarantee

that interference will not occur in a particular installation. If this

device does cause such interference, which can be verified by

turning the device off and on, the user is encouraged to eliminate

the interference by one or more of the following measures:

- Re-orient or re-locate the receiving antenna.

- Increase the distance between the device and the receiver.

- Connect the device to an outlet on a circuit different from the

one which supplies power to the receiver.

- Consult the dealer or an experienced radio/TV technician.

WARRANTY

Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its products hereinafter

referred to as "the Product" or "Products" to be in conformance with its own plans and specifications and to

be free of defects in materials and workmanship under normal use and service for a period of twelve months

from the date of shipment by the Manufacturer. The Manufacturer's obligations shall be limited within the

warranty period, at its option, to repair or replace the product or any part thereof. The Manufacturer shall not

be responsible for dismantling and/or reinstallation charges. To exercise the warranty the product must be

returned to the Manufacturer freight prepaid and insured.

This warranty does not apply in the following cases: improper installation, misuse, failure to follow

installation and operating instructions, alteration, abuse, accident or tampering, and repair by anyone other

than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations or liabilities, whether

written, oral, express or implied, including any warranty of merchantability or fitness for a particular purpose,

or otherwise. In no case shall the Manufacturer be liable to anyone for any consequential or incidental

damages for breach of this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any

person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall

apply to the Product only. All products, accessories or attachments of others used in conjunction with the

Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall

not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or

otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of others,

including batteries, used in conjunction with the Products.

The Manufacturer does not represent that its Product may not be compromised and/or circumvented, or that

the Product will prevent any death, personal and/or bodily injury and/or damage to property resulting from

burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or

protection. User understands that a properly installed and maintained alarm may only reduce the risk of

events such as burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such

will not occur or that there will be no death, personal damage and/or damage to property as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury and/or damage

to property or other loss whether direct, indirect, incidental, consequential or otherwise, based on a

claim that the Product failed to function. However, if the Manufacturer is held liable, whether directly or

indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or

origin, the Manufacturer's maximum liability shall not in any case exceed the purchase price of the Product,

which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive

remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among other things test the

Product and the whole system at least once a week. For various reasons, including, but not limited to,

changes in environmental conditions, electric or electronic disruptions and tampering, the Product may not

perform as expected. The user is advised to take all necessary precautions for his /her safety and the

protection of his/her property.

6/91

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not

returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2002/96/EC Waste Electrical and Electronic Equipment.