Visonic Mkp 150 User manual

DE2462U 1

MKP-150, MKP-151

2-Way Wireless Keypad User's Guide

1. INTRODUCTION

NOTE: RELEVANT TO POWERMAX+ VERSION B AND ABOVE

The MKP-150 / MKP-151 (different color) operates using two-way

encrypted coded transmission and provides aural and visual indications.

For each PowerMax+, PowerMax Pro, PowerMaxComplete,

PowermaxExpress control panel, a maximum of two MKP-150/MKP-151

keypad devices may be enrolled.

The MKP-150/151 includes an optional partition feature. Partitioning

allows you to have up to three independently controllable areas with

different user codes assigned to each partition or one user code

assigned to up to three partitions. A partition can be armed or disarmed

regardless of the status of the other partitions within the system.

Note: The Partition feature appears only after Partitioning is enabled

via the control panel.

The MKP-150/MKP-151 may be operated either by AC power supply

or by battery power. If AC power is used, the device operates

continuously and the system status is constantly updated. If powered

by batteries, the keypad enters sleep mode 15 sec after last key

press. The keypad immediately becomes operational again upon

pressing of any key.

Note: In the event of an AC power failure, the MKP-150/MKP-151

operates on batteries as described above.

The device enables the user to arm/disarm the alarm system, to initiate

emergency/fire/panic alarms and to turn lighting devices on and off.

The main features of the MKP-150/MKP-151 are:

•Status, alarmmemory, and troubledataretrievalfrom the control panel.

•Automatic reporting to the control panel of low battery voltage, AC

failure, tamper.

•Visual indications by red/green/amber LED and LCD display.

•Keypad and LCD backlighting activation.

•Light dim / brightness

•Various audible signals sounded by the speaker in response to

specific actions.

•Automatic supervision messages.

•Diagnostic test of the control panel.

•Two long-life 3 Volt Lithium batteries.

•Wall mounting.

•Friendly programming.

The Power (green) LED lights when operated using AC power. The

Trouble (amber) LED lights if a "trouble" state is currently detected

within the control panel. The Chime (green) LED lights when the chime

function is active. The Arm (red) LED lights when the system is in

armed state (away mode), or flashes (home mode).

A periodic supervision message is transmitted, at regular intervals, from

the MKP-150/MKP-151 to the control panel. This ensures active

participation of the MKP-150/MKP-151 in the system.

Operating power is obtained from two 3 Volt Lithium batteries, or by

AC. A weak battery causes a "low battery" message to be sent to the

control panel.

A Screen Saver appears on the display (if enabled by the installer on the

control panel unit) when no key is pressed for more than 30 seconds.

The display reads “POWERMAX” and the LEDs do not light (to prevent

an intruder of knowing the system status). The normal display returns

after pressing the OFF button followed by entering user code (Refresh

by Code) or after pressing any key (Refresh by Key), depending on the

control panel settings of the installer. If Refresh by Key was selected,

the first key press (except for Fire and Emergency) causes the normal

display to return while a second press performs the key function. In the

case of the Fire and Emergency keys, the first key press causes the

normal display to return and also performs the Fire/Emergency function.

AWAY

MICROPHONE

PLAY MESSAGE

VOLUME UP /

LIGHT BRIGHT

VOLUME DOWN /

LIGHT DIM

CHIME ON/OFF

MUTE SPEAKER

NO ENTRY DELAY

RECORD MESSAGE

LIGHT OFF

PARTITION

SELECTION

ARMING

“AWAY”

ARMING “HOME”

DISARMING

BYPASS

LIGHT ON

EMERGENCY

(Hold for 2 sec.)

FIRE

PANIC

(press both buttons)

“SHOW / OK”

BUTTON

“ESCAPE”

BUTTON

“NEXT”

BUTTON

LCD

WINDOW

“BACK”

BUTTON

SPEAKER

Figure 1: External View

2 DE2462U

2. SPECIFICATIONS

ELECTRICAL

Battery Power Source: Two 3 Volt Lithium batteries, type CR123A

(Sanyo or equivalent).

Battery Life Expectancy: 2 years (for typical use).

AC Power Supply (optional): Plug-in transformer.

120 VAC, 60 Hz / 9 VAC, 0.35 A min. (in the U.S.A.)

230 VAC, 50 Hz / 9 VAC, 0.35 A min.

UL installation: Use transformer type OH-35048AT, manufactured by

Oriental Hero Electrical Factory.

In Europe and elsewhere: Use only Safety National Approved AC

adapter, mains-to-9 VAC, 0.35 A min.

AC Current Drain: Approx. 30 mA standby, 300 mA max. at full load.

Display: Single line, backlighted 16-character LCD and 4 LED indicators.

Control Functions: Home Arming, Away Arming, Bypass, Disarming,

Latchkey, Light ON / OFF, Light Dim / Brightness, Recording, Forced

Arming, Panic, Fire and Emergency calls.

Sleep Mode: Used to minimize current consumption. The unit enters

sleep mode 15 seconds after last use (applies only when using

batteries or when there is a power failure).

Supervision: A periodic supervision message (programmable) is

transmitted automatically once every 15 minutes (Europe), once every

60 minutes (USA), or according to the local standards. This function

can be disabled.

Panic Alarm Message: Activated by simultaneously pressing the

and keys.

Tamper Switch: Normally closed. A tamper signal is transmitted in

three ways: when the MKP-150/MKP-151 case is opened; when the

keypad assembly is separated from the bracket; or if the MKP-

150/MKP-151 unit is ripped from the wall.

Compliance with Standards: FCC part 15, EN 50131-1 Grade 2

Class II, TS 50131-3 and Directive 1999/5/EC

RF SECTION

Operating Frequencies: 315 MHz (in USA & Canada) or other UHF

channels per local requirement in the country of use.

Note: At 315 MHZ the MKP-150 complies with UL 1023.

Receiver Type: Super-heterodyne, fixed frequency

Receiver Range: 600 ft (180 m) in open space

Antenna Type: Spatial

Coding: Two-way wireless protocol

ENVIRONMENTAL

For indoor use only.

Operating Temp. Range: 0°C to 49°C (32°F to 120°F)

Storage Temp. Range: -20°C to 60°C (-4°F to 140°F)

Humidity: 85% relative humidity, @ 30°C (86°F)

PHYSICAL

Dimensions: 172 x 99 x 39 mm (6 7/8 x 3 15/16 x 1 9/16 in.)

Weight: 375 g. (13 oz)

Mounting: Surface-mounted

Color: Light gray

3. INSTALLTION AND WIRING

Perform the procedures as illustrated in the following Figures.

Note: Mount the unit inside the secured premises, in a location providing optimum signal reception from the control panel unit, (refer to Installing

Wireless Systems Installation Guide – The Right Way, document no. DE2000W, for further details).

After removing

the screw,

pull down the

bracket fully

Remove

the bracket

Figure 2: Bracket Removal

Mark and drill 4

holes in mounting

surface. Insert wall

anchors and fasten

the bracket to the

mounting surface

with 4 screws.

Screw

Holes

Screw

Hole

IMPORTANT !

The back tamper

switch will not

activate a tamper

alarm unless this

segment is secured

to the wall with

a screw.

Screw

Hole

Note: Leave at least 3 cm (1.25 in.) free space around the bracket.

Figure 3: Bracket Mounting

ess the tab inwa

and remove the cover

Insert

batteries

(verify proper

polarity) and

close cover

Back

Tamper

Switch

Figure 4: Battery Insertion

VAC

Wiring

Inlets

Connect the 9 VAC

power supply to the

terminal block. Route

the wiring through the

wiring channels.

Note:

The transformer

is optional

Figure 5: Wiring

Match the panel with

the bracket projections.

Pull downward and

secure the bracket with

the locking screw

Figure 6: Panel Mounting

DE2462U 3

4. ENROLLING/DELETING THE KEYPAD FROM THE POWERMAX+ MEMORY

To enroll all the MKP-150/MKP-151 functions (for complete list see PowerMax+ Installer Guide), enter the PowerMax+ Installer Mode from the

PowerMax+ keypad, and proceed as shown in the following illustration.

Note: For PowerMax Pro, PowerMaxComplete and PowerMaxExpress control panels, please refer to the respective Installer Guide.

Note: Refer to PowerMax+

Installer Guide for details on

performing a diagnostic test

(First display is READY

or NOT READY)

READY 00:00

USER SETTINGS

WALK TEST

ENTER CODE

1. NEW INSTL CODE

2. ENROLLING

[installer code]

INSTALLER MODE



ENROL WL 2WAY KP

ENROLL WL DEVICEENROLLING TYPE

[KEYPAD No. 1 to 2]

(e.g. 2)

2way kp No :

2way kp No : 2 2way kp No : 2

2way kp No: 2

Enrolling a wireless

Keypad

for next

enrolling action

<OFF> TO DELETE

press back

tamper

switch

once

(see Fig. 4)

TRANSMIT NOW

Deleting a wireless

Keypad

2way kp No: 2

ENROLL KEYFOB

Black rectangle means

that the KEYPAD No. 2

is already enrolled.



NEXT



NEXT NEXT NEXT

ENROL WL 1WAY KP NEXT

9. DIAGNOSTICS



AWAY

Figure 7: Enrolling / Deleting a MKP-150/MKP-151 Device from PowerMax+ Memory

5. DEFINING MKP-150/MKP-151 PARAMETERS

5.1 Installer Menu Functions

Important: All installer settings affect only the specific keypad on

which the settings were performed.

The Installer menu enables you to perform the following functions:

SUPERVISION

The keypad transmits supervision reports periodically to the control

panel.

The options are: 15 minutes, 1hour and disable.

Note: In FCC installations, the keypad must be set to 1 hour.

PIEZO BEEP

Here you determine whether warning beeps will sound or be muted

during exit and entry delays.

Options: enable beeps, off when home and disable beeps.

BACK LIGHT

The keypad and LCD back light can be activated in one of two ways:

•By key press: back light is activated for ten seconds by a long

press (2 sec) of any key.

•Always on: back light remains on continuously. (Enabled only

when the unit is connected to the AC supply.)

The options are: OFF after 10s and always ON.

JAM DETECTION

Note: For PowerMax+ control panel, this feature is enabled only with

version 3.3.14 and above.

Here you determine whether jamming (interfering transmissions on

the radio channel used by the system) will be detected.

The options are: UL 20/20, EN 30/60, class 6 (30/60), or disable.

RECORD SPEECH

This mode allows you to record up to 5 custom zone names.

SERIAL NUMBER

Enables reading the system serial number for support purposes only.

5.1.1 To Set Supervision Time

Make sure the system is not in Arm mode.

The installer’s menu is accessible only to those who know the

installer’s code, which is 9Î9Î9Î9by factory default.

A. Press the next button (►) repeatedly until the display reads:

INSTALLER MODE

B. Press the Show / OK button (√). The display should read:

ENTER CODE: ___

Note: For control panels with two installer codes, the default

INSTALLER code is 8888 and the default MASTER INSTALLER

code is 9999.

C. Enter the installer code. The display will change to:

SUPERVISION

D. Press <√>.

E. Press <►> repeatedly to select one of the available options.

F. Press <√> to set the selected option.

5.1.2 To Activate the Recording Mode

A. Upon gaining access to the installer menu (see section 5.1.1 A to

C), the display will read “SUPERVISION”.

B. Press <►>; RECORD SPEECH is displayed.

C. Press <√>. The display will change to:

USER TERM #1

Note: User Term refers to the name assigned to the recorded

zone.

Note: It is recommended to assign custom names that are

identical to the custom names defined in the control panel.

D. Press the key until this is displayed briefly:

RECORD A MESSAGE

Immediately thereafter, the display will change to:

TALK NOW

4 DE2462U

E. Do not release the key and start talking immediately (for

example, living room or library), while facing the front panel.

The dark square boxes will slowly disappear one by one, from

right to left. When the last one disappears (5 seconds later) the

following message will be displayed:

RECORDING ENDED

F. Release the key. To check the message, press the key

and listen to the playback.

G. Press <►>. The display will change to:

USER TERM #2

H. Repeat the procedure for User Terms #2 - #5 to record the names

of zones 2 - 5.

5.1.3 To Enable/Disable Piezo Beeps

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> twice; PIEZO BEEP is displayed.

C. Press <√>.

D. Press <►> to select between enable beeps, off when home and

disable beeps.

E. Press <√> to set the selected option.

5.1.4 Keypad Back Light

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until BACK LIGHT is displayed.

C. Press <√>.

D. Press <►> to select between OFF after 10s and always ON.

E. Press <√> to set the selected option.

5.1.5 Jam Detection

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until JAM DETECTION is displayed.

C. Press <√>.

D. Press <►> to select between UL 20/20, EN 30/60, class 6

(30/60), disable and other.

E. Press <√> to set the selected option.

5.1.6 To Read the Device Serial Number

A. Upon gaining access to the installer menu (see section 5.1.1

points A to C) the display will read “SUPERVISION”.

B. Press <►> repeatedly until SERIAL NUMBER is displayed.

C. Press <√> to read the serial number assigned to the unit.

RECORD SPEECH

user term #1



user term #2

user term #3

user term #4

user term #5

READY 00:00

USER SETTING

WALK TEST

ENTER CODE

[installer code]

INSTALLER MODE



SUPERVISION

superv time 15m

superv time 1h



disable

PIEZO BEEP

enable beeps

disable beeps



off when home

(*)

In Canada, “disable”

must be selected.

SERIAL NUMBER

xxxxxxxxxxxxxxxx



xxxxxxxxxxxxxxxx

JAM DETECT

UL 20/20



EN 30/60

class 6 (30/60)

disable

BACK LIGHT

OFF after 10s



always ON

PIEZO BEEP



Partition disabled Partition enabled

Def:P1 P2 P2

Note: The currently saved options are

displayed with a dark box at the right

side of the display.To review the

options, repeatedly click or until

the desired option is displayed, then

click (a dark box will be displayed

at the right side).

Figure 8: Defining MKP-150/MKP-151 Functions

5.2 User Setting Functions

Note: The Partition feature appears only after Partitioning is enabled

via the control panel.

The user settings on your MKP-150/MKP-151 keypad include the

following functions (for instructions see PowerMax+, PowerMax Pro,

PowerMaxComplete, PowerMaxExpress User's guide):

•Set Bypass

•Show Bypass

•Recall Bypass (applicable when Partition is disabled)

•Set Phone Number

•Set User Codes

•Set Voice Option

•Auto Arm Option

•Auto Arm Time

•Squawk Option

•Light by Timer (for further details, refer to the control panel User's

Guide).

•Light by Sensor (for further details, refer to the control panel User's

Guide).

•Make sure the system is not in Arm mode. The display should

read:

READY

TO SET FUNCTIONS

The user's menu is accessible only to those who know the master

user code, which is 1Î1Î1Î1by factory default.

Use this code for initial access, and replace it with a new code known

only to you, (see PowerMax+, PowerMax Pro, PowerMaxComplete,

PowerMaxExpress User's Guide).

A. Press the ►button twice.

The display should read:

USER SETTING

B. Press the √. The display should read:

ENTER CODE: ___

C. Enter your code. The display will change to:

SET BYPASS

Note: If the bypass function is disabled, the display will change to:

SET PHONE NUMBER

D. Having gained access to the user's menu, you may now select

any other item on the User Settings menu as detailed in Figure 9.

DE2462U 5

NOTES

(1) Function inside black rectangles are accessible only if master user code was entered.

(2) Press OK to display the number, state and name of first bypassed zone. Press NEXT/BACK repeatedly to view all the bypassed zones.

(3) To enter “A” (AM) press ( or one of the 3 keys above it), to enter “P” (PM) press (or one of the 3 keys above it). (Not

functional if the time format has been set to the 24 hour clock via the PowerMax+.)

(4) SET/SHOW/RECALL BYPASS menus are accessible only if “manual bypass” has been selected by the installer via the PowerMax+.

(5) In the SET VOICE OPTION, if you select “enable prompts”, the PowerMax+ mute speaker button is active.

(6) RECALL BYPASS is applicable when Partition is disabled.

SHOW BYPASS

RECALL BYPASS

BYPASS LIST

<OK> TO RECALL

(2)

SET BYPASS

NORMAL MODEREADY

<OK> TO BYPASS Z01: BYPASSED

Z01: OPEN

KITCHEN

Alternating

KITCHEN

Alternating

(for checking state of next zone)

ENTER CODE _ _ _ _

INSTALLER MODE

(4)

(4) (example)

SET PHONE NUMBER

)

SET USER CODES user code 1 1 1 1 1 [code]

user code 1

(1)

AUTO ARM OPTION disable autoarm enable autoarm

(if it is the current option)

)[time]

AUTO ARM TIME arm time _ _: _ _A

SQUAWK OPTION

(1)

SET VOICE OPTION enable prompts

(if it is the current option)

(1)(5)

)[4-digit master/user code]

if not satisfied

)

if not satisfied

)

disable prompts disable prompts

enable autoarm

(First display is READY

or NOT READY)

)

)))

)

))

)

BACK

Moving one level

up in the menu

To move within the menus, the

following keys can be used:

SHOW / OK

squawk disable

sqwk low volume

sqwk mid volume

sqwk hi volume

(To review options, use

NEXT or BACK button)

Tel. No .



1st private tel#

Tel. No .



2nd private tel#

Tel. No.



3rd private tel#

Tel. No.



4th private tel#

))

LIGHT BY TIMER

LIGHT BY SENSOR

enable disable disable

)

if not satisfied

)

enable disable disable

)

if not satisfied

USER SETTINGS

(1)

(3)

(1)

ESC

(6)

)

user code 2

)

to select next

user codes (3....8)

)user code 2 1 1 1 1 [code]

)access to part

)

U02:P1 P2 P3 (y=yes)

(for next user codes)

enter partition numbers (e.g.

for partitions 2 & 3 enter 23) U02:P1 P2 P3

Figure 9: User Settings Flow Chart

6. OPERATION

Function Actions

Partition selection

(when enabled) [Partition No.]

Arming HOME (1) (3)

Arming HOME INSTANT (1)

Arming AWAY

AWAY

(1)

Arming AWAY INSTANT

AWAY

(1)

Forced Arming HOME (1)

Forced Arming AWAY

AWAY

(1)

AWAY

Disarming (1)

X-10 device (1-15) ON unit # [1-15]

6 DE2462U

X-10 device (1-15) OFF unit # [1-15]

Light dim / brightness unit # [1-15]



Emergency alarm (≈2 sec.) (5)

Fire alarm (≈2 sec.) (5)

Panic alarm

Latchkey arming

AWAY

[user code](1)

AWAY AWAY

(2)

Quick arm / HOME /

AWAY

(operates only if enabled in

the control panel)

Chime ON/OFF (press again to select option)

Local Recording (press continuously while talking)

Playback

Local Voice On / Off

Testing (1) (3)

Bypass (1)

Duress [duress code] (2580 by

default)

Notes

1. The factory default master user code is 1 1 1 1. The code is not

required if quick arming has been permitted by the installer.

2. For LATCHKEY arming function, press the AWAY key, and then

press the AWAY key again.

3. Pressing a non-valid code combination (not master / user code)

causes a long failure beep.

4. If a keying sequence is not completed within a five second period,

the desired function will not be executed.

5. Emergency, Fire or Panic buttons become active only if enabled

in the control panel.

7. COMPLIANCE WITH STANDARDS

This device complies with the essential requirements and provisions of

Directive 1999/5/EC of the European Parliament and of the Council of 9

March 1999 on radio and telecommunications terminal equipment.

Frequency Allocations for Wireless Devices in European Countries:

•315 MHz is not allowed in any EU member state.

•433.92 MHz has no restriction in any EU member state.

•868.95 MHz (wide band) is allowed in all EU member states.

•869.2625 MHz (narrow band) is not restricted in any EU member state.

The user is cautioned that changes or modifications to the unit, not

expressly approved by Visonic Ltd., could void the user's FCC or

other authority to operate the equipment.

The 315 MHz model of this device complies with Part 15 of the FCC

Rules and RSS-210 of Industry and Science Canada. Operation is

subject to these two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesirable operation.

The digital circuit of this device had been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable protection

against harmful interference in residential installations. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio and television reception. However, there is

no guarantee that interference will not occur in a particular installation. If

this device does cause such interference, which can be verified by

turning the device off and on, the user is encouraged to eliminate the

interference by one or more of the following measures:

- Re-orient or re-locate the receiving antenna.

- Increase the distance between the device and the receiver.

- Connect the device to an outlet on a circuit different from the one

which supplies power to the receiver.

- Consult the dealer or an experienced radio/TV technician.

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser

only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a

period of twelve (12) months from the date of shipment by the Manufacturer.

This Warranty is absolutely conditional upon the Product having been properly installed, maintained and

operated under conditions of normal use in accordance with the Manufacturers recommended installation

and operation instructions. Products which have become defective for any other reason, according to the

Manufacturers discretion, such as improper installation, failure to follow recommended installation and

operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or

tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty.

The Manufacturer does not represent that this Product may not be compromised and/or circumvented or

that the Product will prevent any death and/or personal injury and/or damage to property resulting from

burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or

protection. The Product, properly installed and maintained, only reduces the risk of such events without

warning and it is not a guarantee or insurance that such events will not occur.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR

OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER

WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE,

INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY

ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR

DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY

INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT,

INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT

FAILED TO FUNCTION.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising

under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN

ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated

damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer.

When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and

warranty and he recognizes having been informed of.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these

limitations may not apply under certain circumstances.

The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning

of any telecommunication or electronic equipment or any programs.

The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the

Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or

replacement shall not extend the original Warranty period. The Manufacturer shall not be responsible for

dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the

Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the

Purchaser and are not included in this Warranty.

This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any

person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall

apply to the Product only. All products, accessories or attachments of others used in conjunction with the

Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall

not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially

or otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of

others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original

Purchaser and is not assignable.

This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is

contrary to the Law in the state or country were the Product is supplied shall not apply.

Warning:The user must follow the Manufacturer’s installation and operational instructions including testing

the Product and its whole system at least once a week and to take all necessary precautions for his/her

safety and the protection of his/her property.

1/08

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not

returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2002/96/EC Waste Electrical and Electronic Equipment.