Visonic POWERMAXCOMPLETE PANEL - Assembly instructions

D-300885 1
PowerMaxComplete
Fully Supervised Wireless Alarm Control System Installer Guide
TABLE OF CONTENTS
1. INTRODUCTION.......................................................3
2. SPECIFICATIONS.....................................................3
2.1 General Data.......................................................3
2.2 RF Section ..........................................................3
2.3 Electrical Data.....................................................3
2.4 Communication...................................................4
2.5 Physical Properties .............................................4
3. INSTALLATION.........................................................4
3.1 Unpacking the Equipment...................................4
3.2 Supplying Power to the Unit................................4
3.3 System Planning & Programming.......................4
3.4 Mounting .............................................................4
3.5 Wiring..................................................................4
3.6 Backup Battery Insertion.....................................7
3.7 Optional GSM Module Mounting ...........................7
3.8 DUAL RS-232 Optional Module Mounting..........8
3.9 Optional Expander Module Mounting .................8
3.10 Power Cable Connection..................................8
3.11 Control Panel Final Closure............................10
4. PROGRAMMING.....................................................11
4.1 INTRODUCTION ..............................................11
4.1.1 General Guidance..........................................11
4.1.2 Entering an Invalid Installer Code.....................11
4.1.3 Installer’s Menu..............................................11
4.1.4 Setting a New Installer Code .........................11
4.1.5 Setting a New Installer Code in
PowerMaxComplete that has 2 Installer Codes.......11
4.2 ENROLLING WIRELESS DEVICES AND KEYFOB
TRANSMITTERS.........................................................12
4.2.1 General Guidance..........................................12
4.2.2 Enrolling Type................................................12
4.2.3 Enroll/Delete Sensors ....................................12
4.2.4 Enroll/DeleteKeyfobTransmitters.......................12
4.2.5 Enroll/Delete Wireless Commander......................12
4.2.6 Enroll/Delete 2-Way Keypad ..........................12
4.2.7 Enroll/Delete Wireless Siren...........................12
4.2.8 Enroll/Delete Proximity Tags ..........................12
4.3 DEFINING ZONE TYPES, NAMES & CHIME
ZONES.........................................................................14
4.4 DEFINING CONTROL PANEL PARAMETERS....15
4.4.1 Preliminary Guidance.....................................15
4.4.2 Entry Delays 1&2 ...........................................15
4.4.3 Exit Delay.......................................................15
4.4.4 Bell Time........................................................15
4.4.5 Abort Time......................................................15
4.4.6 Alarm Cancel..................................................15
4.4.7 Quick Arm ......................................................15
4.4.8 Bypass............................................................15
4.4.9 Exit Mode.......................................................15
4.4.10 Piezo Beeps.................................................16
4.4.11 Trouble Beeps..............................................16
4.4.12 Panic Alarm..................................................16
4.4.13 Swinger Stop................................................16
4.4.14 Cross Zoning................................................16
4.4.15 Supervision ..................................................16
4.4.16 NOT READY................................................ 16
4.4.17 AUX Button A............................................... 16
4.4.19 Jam Detect................................................... 16
4.4.20 Latchkey....................................................... 16
4.4.21 “Not Active”.................................................. 16
4.4.22 Back Light.................................................... 17
4.4.23 Duress.......................................................... 17
4.4.24 Piezo Siren................................................... 17
4.4.25 Reset Option................................................ 17
4.4.26 Tamper Option............................................. 17
4.4.27 Siren On Line............................................... 17
4.4.28 Memory Prompt ........................................... 17
4.4.29 Disarm Option.............................................. 17
4.4.30 Bell/Rep. Option........................................... 17
4.4.31 Low-Bat Ack................................................. 17
4.4.32 Screen Saver............................................... 17
4.4.33 Confirm Alarm.............................................. 17
4.4.34 AC FAIL REP............................................... 17
4.4.36 User Permission .......................................... 17
4.4.38 Batttery Type................................................ 17
4.5 DEFINING COMMUNICATION PARAMETERS... 19
Preliminary Guidance.............................................. 19
4.5.1 Autotest Time................................................. 19
4.5.2 Autotest Cycle................................................ 19
4.5.3 Area Code...................................................... 19
4.5.4 Out Access No............................................... 19
4.5.5FirstCentralStationTel....................................... 19
4.5.6 First Account No. ........................................... 19
4.5.7 2ND Central Station Tel..................................... 19
4.5.8 Second Account No....................................... 19
4.5.9 Report Format................................................ 19
4.5.10 4/2 Pulse Rate ............................................. 19
4.5.11 Reporting to Central Stations ......................... 19
4.5.12 Report CNF Alarm......................................... 19
4.5.13 Send 2WV Code............................................ 19
4.5.14 Two-WayVoice Central Stations..................... 20
4.5.15 Ring Back Time ........................................... 20
4.5.16 Dialing Attempts........................................... 20
4.5.17 Set Private Tel. No....................................... 20
4.5.18 Two-Way Voice - Private Phones................... 20
4.5.19 Private Tel. Dialing Attempts ....................... 20
4.5.20 Reporting to Private Telephones.................... 20
4.5.21 Tel. Acknowledge .......................................... 20
4.5.22 Pager Tel. No............................................... 20
4.5.23 Pager’s PIN No............................................ 20
4.5.24 Reporting to a Pager.................................... 20
4.5.25 Recent Closure............................................ 20
4.5.26 Remote Access............................................ 20
4.5.27 Mast. DL Code............................................. 20
4.5.28 Inst. DL Code............................................... 22
4.5.30 Zone Restore............................................... 22
4.5.31 Upload Option.............................................. 22
4.5.32 Dialing Method............................................. 22
4.5.33 Line Failure Report...................................... 22
4.5.34 UL/DL Tel. Number...................................... 22
4.5.35 System Inactivity Report.............................. 22
4.5.38 Ambient Level.............................................. 22
4.5.39 Report 24h Zones........................................ 22

2 D-300885
4.6 DEFINING GSM PARAMETERS ..........................22
4.6.1 GSM Module Installation................................22
4.6.2 1st, 2nd, 3rd & 4th SMS Number.....................22
4.6.3 Reporting to SMS Phone Number ....................22
4.6.4 GSM Line Failure Reporting ..........................23
4.6.5 GSM Line Purpose.........................................23
4.6.6 GSM Auto Test...............................................23
4.8 DEFINING OUTPUT PARAMETERS....................23
4.8.1 Preliminary Guidance.....................................23
4.8.2 Define PGM....................................................23
4.8.3 Defining INT/STRB ........................................23
4.8.4 PGM General Definition.................................23
4.9 DEFINE VOICE .....................................................24
4.9.1 Record Speech ..............................................24
4.9.2 Voice Box Mode.............................................24
4.10 DIAGNOSTIC TEST............................................25
4.11 USER FUNCTIONS.............................................26
4.12 RETRIEVING FACTORY DEFAULTS ................26
4.13 SERIAL NUMBER ...............................................26
4.14 CALLING UPLOAD/DOWNLOAD SERVER.......26
5. TESTING PROCEDURES.......................................27
5.1 Preparations......................................................27
5.2 Diagnostic Test .................................................27
5.3 Keyfob Transmitter Test....................................27
5.4 PGM output ON/OFF Test................................27
5.5 Emergency Transmitter Test.............................27
6. MAINTENANCE.......................................................27
6.1 Dismounting the Control Panel.........................27
6.2 Replacing the Backup Battery...........................27
6.3 Fuse Replacement............................................27
6.4 Replacing/Relocating Detectors .......................27
7. READING THE EVENT LOG .................................. 28
APPENDIX A. Detector Deployment & Transmitter
Assignments................................................................ 29
A1. Detector Deployment Plan.................................. 29
A2. Keyfob Transmitter List....................................... 29
A3. Emergency Transmitter List................................ 30
A4. Non-Alarm Transmitter List................................. 30
APPENDIX B. PGM Output Assignment..................... 30
APPENDIX C. Event Codes........................................ 30
Contact ID Event Codes ......................................... 30
SIA Event Codes..................................................... 30
4/2 Event Codes ..................................................... 31
Understanding the Scancom Reporting Protocol Data
Format..................................................................... 32
APPENDIX D. Programmable Zone Types................. 32
D1. Delay Zones ...................................................... 32
D2. Emergency Zones.............................................. 32
D3. Fire Zones........................................................ 32
D4. Flood Zone....................................................... 32
D5. Gas Zone.......................................................... 32
D6. Interior Zone..................................................... 32
D7. Interior Follower Zones .................................... 32
D8. Non-Alarm Zones............................................. 32
D9. Perimeter Zones............................................... 32
D10. Perimeter Follower Zones.............................. 33
D11. 24-Hour Zones............................................... 33
APPENDIX E. PowerMaxComplete Compatible Devices
..................................................................................... 33
E1. PowerMaxComplete Compatible Detectors...... 33
E2 PowerMaxComplete Compatible Transmitters . 33
E3 PowerMaxComplete Compatible WL Siren........... 34
E4. PowerMaxComplete Compatible GSM Modem34
E5. Optional Speech Box........................................ 34
MESSAGE TO THE INSTALLER
The PowerMaxComplete control panel is supplied with 2 instruction manuals:
Installer Guide (this manual - for your exclusive use)
User’s Guide (for your use during installation only - Must be handed over to the master user after testing the system).
Appendices A.1 and A.2 will help you prepare an installation plan. Please take time to fill out the forms - your job will
become much easier and confusion will be prevented. Filling out the forms will also help you create a list of detectors and
transmitters that must be obtained for the particular application. Compatible detectors and transmitters are listed and
described briefly in Appendix E.
Remember - it is advisable to power up the control panel temporarily after unpacking and program it on the work bench, in
accordance with the installation plan.
The programming flow charts in the programming section show all options available for each parameter. Factory defaults
are marked with a dark box to their right, and other options (that can be selected instead) are marked by clear boxes. This
method allows you to put a checkmark in the appropriate clear box whenever you deviate from the factory defaults.
Most of the programming section paragraph numbers correlate with the programming menu numbers. For example,
paragraph 4.4.19 describes the "Jam detect", that exists in menu 4 (define panel), sub-menu 19 (Jam detect).
Although setting the correct time and date is one of the user tasks, we recommend that you set the time and date in the
course of programming. Access to the “User Settings” for the installer is possible through item 10 on the installer‘s menu or
through the user menu (see User’s manual section 7).
After programming, proceed to install the system as detailed in the Installation Instructions, from paragraph 3.4 onward.
The installer should verify line seizure. Be aware of other phone line services such as DSL. If DSL service is present
on the phone line, you must install a filter. It is suggested to use the DSL alarm filter model Z-A431PJ31X
manufactured by Excelsus Technologies, or equivalent. This filter simply plugs into the RJ-31X jack and allows
alarm reporting without breaking the internet connection.

D-300885 3
1. INTRODUCTION
The PowerMaxComplete is a user and installer-friendly,
30-zone fully-supervised wireless control system. The
system is designed to function in an appealing way to the
user and also offers features that make installers’ life
easier than ever before:
EASY TO INSTALL
•Optional plug-in RS-232 module that enables
connection of an external GSM Module or local
computer.
EASY TO MAINTAIN
•Status, alarm memory and trouble data are displayed
upon request.
•Diagnostic test provides visual and audible indication of
the signal level of each detector.
•Remote control and status verification from distant
telephones.
•Event log stores and displays information.
•Upload / download from distant computer via telephone
line or cellular modem.
QUICK PROGRAMMING
•Simple programming logic, fully menu driven.
•Multiple-choice selection of options for each parameter.
•Unequivocal visual prompts and audible signals.
•Installer access to the user menu.
2. SPECIFICATIONS
2.1 General Data
Zones Number: 28 wireless, 2 hardwired (zones 29 & 30).
Hardwired Zone Requirements: 2.2 kΩ E.O.L. resistance
(max. resistance of wires 220 Ω).
Zone Types: Interior follower, interior, perimeter,
perimeter follower, delay 1, delay 2, 24h silent, 24h
audible, fire, non-alarm, emergency, gas and flood.
User Codes: 8 codes, 4 digits each (9999 different
combinations). Code 0000 is not allowed.
Control Facilities:
- Integral keypad
- PowerCode / Code-Secure™ hand-held transmitters
- Wireless commander
- Remote telephone
- Local or remote computer
Display: Single line, Backlit 16-character LCD.
Arming Modes: AWAY, HOME, AWAY-INSTANT, HOME-
INSTANT, LATCHKEY, FORCED, BYPASS.
Alarm inhibited during a single arming period (swinger
stop) after: 1, 2, 3, alarm/tamper/fault, or not inhibited
(programmable / selectable).
Alarm Types: Silent alarm, siren alarm or sounder
(internal) alarm, in accordance with zone attributes.
Siren Signals: Continuous (intrusion / 24 hours / panic);
triple pulse - pause - triple pulse... (fire).
Siren (bell) Timeout: Programmable (4 min. by default)
Internal Sounder Output: At least 85 dBA at 10 ft (3 m)
Supervision: Programmable time frame for inactivity alert
Special Functions:
- Speech and sound control
- Chime zones
- Diagnostic test and event log
- Remote control by telephone
- Computer control and data download/upload
- Calling for help by using an emergency transmitter
- Tracking inactivity of elderly, physically handicapped and
infirm people
- Family message center (recording and playback)
- Two-way voice communication
Data Retrieval: Status, alarm memory, trouble, event log.
Real Time Clock (RTC): The control panel keeps and
displays time and date.
Compliance with U.S. Standards:
Meets FCC 47 Part 15 and Part 68 requirements.
Compliance with European CE Standards:
EN 50082-1, EN301489-3,7, EN6100-4-6, EN60950,
EN300220, EN50130-4, EN50130-5, EN50131-3
The PowerMaxComplete is compatible with the RTTE
requirements - Directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999.
According to the European standard EN50131-1, the
PowerMaxComplete security grading is 2 – "low to medium
risk" and environmental classification is II – "indoor general"
and the power supply type is A.
GSM standards:
Europe : Complies with CE standards 3GPP TS 51.010-
1, EN 301 511, EN 50361, EN301489-7
USA: FCC 47 Part 22 (GSM850) and Part 24 (GSM
1900). UL1637, UL1635, UL1023, UL985, ULC-S545-02,
ULC C1023.
EMC standard: FCC 47 Part 15.
SAR standards: FCC rule 2.1093, FCC Docket 96-326 &
Supplement C to OET Bulletin 65
2.2 RF Section
Operating Frequencies (MHz): 315 (in USA & Canada),
433, 868.95 or other UHF channel per local requirement in
the country of use.
Receiver Type: Super-heterodyne, fixed frequency
Receiver Range: 600 ft (180 m) in open space
Antenna Type: Spatial diversity
Coding: PowerCode and/or CodeSecure™
2.3 Electrical Data
Power Supply: Internal switching power supply 100VAC
to 240VAC, 50/60 Hz, 0.5A / 12.5 VDC, 1.6A.
Current Drain: Approx. 40 mA standby, 1400 mA at full
load.
Site External Siren Current (EXT): 450* mA max @ 10.5
VDC minimum when powered by AC & DC (battery).
Site Internal Siren Current (INT): 450* mA max. @ 10.5
VDC minimum when powered by AC & DC (battery)
PGM Output Current: 100* mA max.
Wired Detectors (zones 29&30) Total (Sum) Current: 36*
mA max.
High Current / Short Circuit Protection: All outputs are
protected (automatic reset fuse).
* Total PowerMaxComplete output current (of INT & EXT
sirens, PGM output and detectors) cannot exceed 550 mA.

4 D-300885
Backup Battery Options:
Maximum external devices current (1)
Backup
period
1300 mAh
6 Battery
Pack (2)
1800 mAh
8-Battery
Pack (3)
2200 mAh 8-
Battery Pack (4)
4h 210mA 300mA 380mA
8h 90mA 160 mA 200mA
12h 45mA 90 mA 120 mA
24h 0mA 25 mA 45mA
36h (no backup) 5mA 15mA
48h (no backup) (no backup) 0mA
1Devices that are connected between 12V terminal
and GND of PowerMaxComplete, that includes
internal GSM and proximity reader.
27.2V 1300 mAh, rechargeable NiMH battery pack,
p/n GP130AAH6BMX, manufactured by GP.
39.6V 1800 mAh, rechargeable NiMH battery pack,
p/n GP180AAH8BMX, manufactured by GP.
4 9.6V 2200 mAh, rechargeable NiMH battery pack
(special order).
Maximum battery recharge time: 72 hours
Battery Test: Once every 10 seconds.
2.4 Communication
Built-in Modem: 300 baud, Bell 103 protocol
Data Transfer to Local Computer: Via RS232 serial port
Report Destinations: 2 central stations, 4 private
telephones, 1 pager.
Reporting Format Options: SIA, Pulse 4/2 1900/1400 Hz,
Pulse 4/2 1800/2300 Hz, Contact ID, Scancom.
Pulse Rate: 10, 20, 33 and 40 pps - programmable
Message to Private Phones: Tone or voice
Message to Pager: PIN No.Alarm Type Zone No.
Ring Detection: The unit does not support ring detection
without DC voltage present on the telephone lines.
2.5 Physical Properties
Operating Temp. Range: 14°F to 120°F (-10°C to 49°C)
Storage Temp. Range: -4°F to 140°F (-20°C to 60°C)
Humidity: 85% relative humidity, @ 30°C (86°F)
Size: 266 x 206 x 63 mm (10-7/16 x 8-18 x 2-1/2 in.)
Weight: 1.44Kg (3.2 pounds) (with battery)
Color: White
3. INSTALLATION
3.1 Unpacking the Equipment
Open the cardboard packing box and check whether all
items have been included. If you find out that an item is
missing, contact your vendor or dealer immediately.
3.2 Supplying Power to the Unit
Connect power to the PowerMaxComplete temporarily
(see figure 3.10). Alternatively, you may power up from the
backup battery, as shown in figure 3.3.
Disregard any “trouble” indications pertaining to lack of
battery or lack of telephone line connection.
3.3 System Planning & Programming
It pays to plan ahead - use the tables in appendices A and
B at the end of this guide to register the intended location
of each detector, the holder and assignment of each
transmitter.
Gather up all transmitters and detectors used in the
system and mark each one in accordance with your
deployment plan.
Program the system now as instructed in the
programming section.
3.4 Mounting
Required tool: Philips screwdriver #2.
PowerMaxComplete mounting process is shown in figure
3.1 - 3.11.
3.5 Wiring
Required tools: Cutter and slotted screwdriver - 3 mm
blade.
PowerMaxComplete wiring is shown in figure 3.2.

D-300885 5
Back unit
Mark 4 drilling points on mounting surface
3
1
Release
screws
4
Drill 4 holes and insert wall anchors 5
Fasten the back unit with 4 screws
Figure 3.1 – Back Unit Mounting
Connect telephone cable to SET connector and telephone line cable to LINE connector (through the desired wiring cable entry).
PHONE WIRING
PHONE WIRING IN NORTH AMERICA
RJ-31X
CORD
HOUSE
PHONES
RJ-31X
8-POSITION
RJ-31X PLUG
BROWN
GRAY
GRN
RED LINE
FROM
STREET
123
4
5
6
7
RJ-31X JACK
GRAY
BROWN
GREEN
RED

6 D-300885
ZONE 29 & SIREN WIRING
MAGNETIC CONTACT
ORANY OTHER
CONTACT
(NOT A DETECTOR)
SITE EXTERNALSIREN
MG ELECTRONICS
MG441PDS ONLY
Alarm
N.C.
2.2 kΩ
OPTIONAL EXPANDER MODULE
ZONES, SIRENS, AUDIO BOX AND WIRED DETECTORS WIRING
MIC SPK GND PGM EXT.- 12V SRN+ IN.- Z29 GND Z30
SITE
INTERNAL
SIREN OR
STROBE
SITE EXTERNAL
SIREN MG441PDS
ONLY
EXPANDER
VOICE BOX
Note
Regarding zones 29 & 30, the Control
Panel “sees” a specific resistance
according to the event, as follows:
Normal (no alarm & no tamper): 2.2 kΩ
Alarm event: 4.4 kΩ
Tamper event: Infinite resistance
CONNECT WIRED DETECTORS AS FOLLOWS:
(*)
Power
ZONE 29 /
ZONE 30 GND
TAMP
N.C.
12V(*)
Alarm
N.C.
ZONE 29 /
ZONE 30
Power
GND
2.2 kΩ
12V
Alarm
N.C.
Detector with
Tamper switch Detector without Tamper switch
Note
The EXPANDER module
is an optional module.
If this optional module is
not used, a small 4-
terminal strip is used
instead (2 terminals for
zone 29 and 2 terminals
for siren).
Caution:
Whenusing the Expander,
the internal siren and
Zone 29 must be wired
via the Expander
and not via the
control panel.
Figure 3.2 - Wiring
Notes for EXPANDER module wiring:
* Zone 29/GND and Zone 30/GND terminals can be
connected to a normally closed contact of a detector,
switch (for example a Tamper switch of any device), or
a pushbutton, via a 2.2 K
Ω resistor. The 12V terminal
can be used to supply 12V (up to 36mA) to a
detector (if necessary).
** The EXT terminal can be used to trigger an external siren.
The INT terminal can be programmed for an "internal
siren" or "strobe" (see DEFINE OUTPUTS - DEFINE
INT/STRB in par. 4.8).
The 12V and "GND" terminals can be connected to a
siren (for constant DC power supply).
WARNING! When plugging terminals back into place, be
sure to align them carefully with the pins on the PCB.
Misaligned or reverse insertion of terminals may damage
internal PowerMaxComplete circuits!
IMPORTANT! The terminals for internal and external
sirens are DC outputs intended for 12V sirens. Connecting
a loudspeaker to any of these outputs will cause a short
circuit and will damage the unit.

D-300885 7
Notes for UL installations
a. The sirens connected to the sites INTERNAL or
EXTERNAL SIREN in the EXPANDER must be
suitable for burglar alarm applications. If UL fire
installation is required, all installed accessories must
comply with UL fire standards. Any external siren used,
must be UL listed and shall be rated to operate under
the voltage specified in the Specifications.
Note: The siren on the control panel PCB is non-UL
compliant.
b. A device that is connected to PGM terminal should not
exceed the current consumption defined for the 24-hour
backup period listed in the Backup Battery Options table
(see section 2.3).
c. The system shall be installed in accordance with Chapter
2 of the National Fire Alarm Code, ANSI/NFPA 70.
d. All wiring should be acceptable for class 1 systems as
defined by the National Electrical Code, ANSI/NFPA
70. No. 26 AWG or larger telecommunication line cord
shall be used.
e. The system shall be installed in accordance with CSA
C22.1 Canadian Electrical Code, Part 1.
f. A minimum spacing of 1/4 inch shall be maintained
between the telephone wiring and the low voltage wiring
(zones, bell circuit, etc). Do not route the LINE and SET
wires in the same wiring channel with other wires.
3.6 Backup Battery Insertion
Open battery compartment cover (see drawing below).
Insert one 6-battery pack or 8-battery pack and connect its
connector as shown below.
Front unit
Battery cable
Figure 3.3 - Battery Insertion
3.7 Optional GSM Module Mounting
Note: The GSM module can be used with an internal or
external antenna.
Caution: Do not install or remove the GSM module when
the system is powered by AC power or backup battery.
Plug in the GSM Module and fasten it with the screw:
GSM Front
unit
Figure 3.4 - Optional GSM Module Mounting
Insert the SIM card into the GSM module:
Internal
GSM
antenna
Internal GSM
antenna cable
External GSM
antenna cable
GSM antenna (internal /
external) connector
1
Slide top
cover
Lock cover
to close
6
SIM card insertion
IMPORTANT
1.Before inserting SIM
card, deactivate its
PIN code (by using a
cellular telephone).
2.Do not insert or
remove SIM card
when the control
panel is powered by
AC power or battery.
4
Slide SIM
card into
cover
5
Rotate cover
to close
2
Open
cover Align SIM card in cover
(note cover
orientation)
3
Figure 3.5 - SIM Card insertion
For internal antenna only: Remove the paper strip from
the antenna sticker and stick the antenna on the control
panel. Connect the antenna to the control panel GSM
antenna connector

8 D-300885
Antenna cable
Internal
GSM
antenna
Connector
Figure 3.6 - GSM Internal Antenna Mounting
For external antenna only: Connect the external
antenna to the GSM antenna connector. Verify that the
antenna cable routing enables proper closing of the control
panel.
GSM antenna
connector
External
GSM
antenna
Figure 3.7 - GSM External Antenna Connection
3.8 DUAL RS-232 Optional Module
Mounting
The DUAL RS-232 is a Module that enables connection of
any two simultaneous devices, such as Local PC or
external GSM Module.
The external GSM unit enables the PowerMaxComplete
system to operate over a cellular network (for details
regarding the GSM modem features and connections,
refer to the external GSM Modem installation instructions).
To install the DUAL RS-232 module into the control panel,
press it into the marked location (see drawing below) until
a click is heard.
Connect a local PC or external GSM module, to one of the
DUAL RS-232 module connectors, as shown below.
Connector for PC
Connector for external
GSM or PC
DUAL RS-232 MODULE
Figure 3.8 – DUAL RS-232 Module Mounting
3.9 Optional Expander Module
Mounting
The EXPANDER module enables connection of speech
box, site external siren, site internal siren or strobe and
connection of wired detector to zone number 29 and 30.
The EXPANDER module also enables connection of a
desired device to PGM (programmable) output that is
activated according to a predefined conditions.
Mount the Expander module as shown below.
2 Clips
Connect the
Expander
Module flat
cable to the front
panel
EXPANDER
receptacle.
The receptacle
with strain relie
f
clip is for the
front unit - do not
connect to the
back unit!
Strain relief clip
2
1
Press the
EXPANDER
module in the back
panel between its
2 clips.
Figure 3.9 – EXPANDER Module Mounting
3.10 Power Cable Connection
Connect the power cable and close the control panel as
shown in figure 3.10.
Socket-outlet shall be installed near the equipment and
shall be easily accessible.

D-300885 9
Connect the power supply
output cable to the power
connector in the front
panel.
2
Safety
cover
(*)
Power
supply
unit
Power cable clamp
options
For thin
cable For thick cable (reversed clamp)
Insert power cable through the desired wiring
channel (see step 1), route it to the power supply
unit and connect its 2 wires to the power supply
terminal strip with screwdriver. Fasten power cable
by its clamp (see also step 2 - this clamp can be
reversed to fit thick/thin cable) and close the safety
cover.
1
Thick cable
entry: Pull out a
desired wiring
plastic cap (1 of 4).
1
Extract cable clamp
for use in the next
step.
2
Power Connection for all Countries Except USA
Power Cable Clamp Extraction
Connect the power adapter
to the front panel power
connector.
Power Connection for USA Only
Figure 3.10 - Power Cable Connection
* Do not route wiring in this area, to enable proper closure of the control panel.

10 D-300885
3.11 Control Panel Final Closure
Control panel final closure is shown below.
Close the panel and
fasten the 2 screws
1
Connect the flat cables,
between front and back units,
in their respective connectors
(up to 3, according to options).
Figure 3.11 - Final Closure

D-300885 11
4. PROGRAMMING
4.1 INTRODUCTION
4.1.1 General Guidance
We recommend to program the PowerMaxComplete on the
work bench before actual installation. Operating power may be
obtained from the backup battery or from the AC power supply.
The installer’s menu is accessible only to those who know
the installer’s 4-digit code, which is 9999 by factory default.
Note: Access to the installer menu, in PowerMaxComplete
that has "User Permission" enabled (for example in UK) is
accessible only at the end of the user menu. This option
can be changed is necessary (see par. 4.4.36).
For PowerMaxComplete that has 2 installer codes (not
applicable in UK), the default INSTALLER code is 8888
and the default MASTER INSTALLER code is 9999.
The following actions can be done only by using the
master installer code:
•Changing master installer code.
•Resetting the PowerMaxComplete parameters to the
default parameters,
•Defining specific communication parameters, as
detailed in a note in figure 4.5.
Obviously, you are expected to use this code only once for
gaining initial access, and replace it with a secret code
known only to yourself.
You will mainly use 5 control pushbuttons during the entire
programming process:
- to move one step forward in a menu.
- to move one step backward in a menu.
-to enter the relevant menu or confirm data.
- to move one level up in a menu.
- to return to the "OK TO EXIT" state.
The sounds you will hear while programming are:
- Single beep, heard whenever a key is pressed.
- Double beep, indicates automatic return to the
normal operating mode (by timeout).
☺-Happy Melody (- - - –––), indicates successful
completion of an operation.
-Sad Melody (–––––), indicates a wrong move
or rejection.
4.1.2 Entering an Invalid Installer Code
If you enter an invalid installer code 5 times, the keypad
will be automatically disabled for 90 seconds and the
message WRONG PASSWORD will be displayed.
4.1.3 Installer’s Menu
The installer's menu is shown in figure 4.1a. The text in
rectangles represents the current PowerMaxComplete
display.
4.1.4 Setting a New Installer Code
To set an installer code, perform the actions that are
presented in figure 4.1b. When you are instructed to enter
code, enter a 4-digit code.
4.1.5 Setting a New Installer Code in
PowerMaxComplete that has 2
Installer Codes
For PowerMaxComplete with 2 installer codes,
INSTALLER code (default 8888) and MASTER
INSTALLER code (default 9999), set new codes as shown
in figure 4.1c.
For details regarding the different authorization levels
when logging in with installer code and master installer
code, refer to the note inside figure 4.5 (DEFINE COMM).
By using the master installer code, the menu enables
changing both master installer code and installer code.
By using the installer code, the menu enables changing
the installer code only.
(See figure 4.9)
(See figure 4.3)
(See figure 4.4)
(See figure 4.5)
(See figure 4.8 )
(See chapter 7
in User Guide)
(See figure 4.2)
14. START UL/DL
13. SERIAL NUMBER
12. FACTORY DEFLT
11. USER SETTINGS
10. DIAGNOSTICS
9. DEFINE VOICE
8. DEFINE OUTPUTS
5. DEFINE COMM.
4. DEFINE PANEL
3. DEFINE ZONES
2. ENROLLING
1. NEW INSTL CODE
ENTER CODE
INSTALLER MODE
USER SETTING
NORMAL MODE
READY 00:00
[installer code]
(First display is READY
or NOT READY)
(See figure 4.10)
(See fig. 4.1b & 4.1c)
(See par. 4.12)
(Control Panel
serial number
display)
<OK> TO EXIT
(See section 4.14)
(See figure 4.6)
6. DEFINE GSM
(*)
(**)
[master/ user code]
USER CODE
(*)
(*) Applicable only when "USER PERMIT" function is enabled
(see par. 4.4.36 - USER PERMIT)
(**) Optional feature.
Figure 4.1a - Installer’s Menu

12 D-300885
(See fig. 4.1a)
1. NEW INSTL CODE
NEW INST. CODE
INST. CODE xxxx
[code]
Figure 4.1b - Setting a New Installer Code (see note)
By using
INSTALLER CODE
INST. CODE xxxx
NEW INST. CODE
[code]
1. NEW INSTL CODE
(see fig. 4.1a) (see fig. 4.1a)
[code]
1. NEW INSTL CODE
NEW MASTER CODE
MASTER CODE xxxx [code] INST. CODE xxxx
NEW INST. CODE
By using
MASTER INSTALLER CODE
Figure 4.1c - Setting a New Installer Code
in System with Inst. & Master Inst. Codes (see note)
Note: Installer Code should never be programmed as
“0000”. Doing so will lock the user out of the installer menu!
4.2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS
4.2.1 General Guidance
The ENROLLING mode has the following sub-modes:
•ENROLLING TYPE (wireless devices)
•ENROLL SENSORS.
ENROLL KEYFOB (multi-button CodeSecure
transmitters)
•ENROLL WL 1WAY KP (wireless commander MCM-140+)
•ENROLL WL 2WAY KP (wireless 2-way keypad MKP-150/
MKP-151)
•ENROLL WL SIREN (wireless siren)
•ENROLL PROX TAG (proximity tag)
Before beginning, gather all the devices that you intend to
enroll and make sure they all have batteries installed.
Your control panel must recognize the unique identification
code (ID) of each such device in order to supervise them,
receive their signals and respond accordingly.
Attention! CodeSecure transmitters are mainly used for
arming/disarming and can not be enrolled to zones. In
order to enroll to zones, use only non-CodeSecure
wireless devices.
4.2.2 Enrolling Type
Here you determine whether to enroll a wireless device by
normal transmission or by device Tamper function
(opening its cover). Options: normal, or by tamper.
4.2.3 Enroll/Delete Sensors
For PowerMaxComplete without expander module:
Magnetic contact or any other contact (not a detector) can
be enrolled in zone 29.
For PowerMaxComplete with expander module: Wired
detectors can be enrolled in zones 29&30 and wireless
detectors can be enrolled in zones 01-28.
STOP
•Before enrolling, the lens at the front of PIR
and dual-technology sensors should be
masked to prevent inadvertent transmission.
•Make sure that magnetic contact transmitters are
together with their magnets, to prevent them from
sending alarm transmissions.
To enroll / delete wired / wireless sensors, refer to Fig. 4.2.
4.2.4 Enroll/Delete Keyfob Transmitters
Keyfob transmitters are multi-button wireless CodeSecure™
transmitters. Eight system users use them for better,
quicker and safer control over various system functions.
To enroll / delete 1-way or 2-way keyfob transmitters, refer
to figure 4.2.
4.2.5 Enroll/Delete Wireless Commander
The Wireless Commander (MCM-140+) is a remote control
unit that enables the user to remotely control the system.
To enroll / delete up to 8 wireless commanders, refer to
figure 4.2 (Enroll WL 1-way KP).
4.2.6 Enroll/Delete 2-Way Keypad
The 2-way keypad, type MKP-150/MKP-151, enables the
user to remotely control the system and also to receive
data from the system (status, alarm and trouble data). To
enroll up to two 2-way keypads, refer to figure 4.2.
4.2.7 Enroll/Delete Wireless Siren
The wireless siren is a remote siren that is activated upon
predefined events by the PowerMaxComplete system. To
enroll / delete up to 2 wireless sirens, refer to figure 4.2.
4.2.8 Enroll/Delete Proximity Tags
Proximity tags enable authorized people to enter restricted
areas. Presenting valid proximity tag, while the system is
armed, causes the system to disarm. Presenting valid
proximity tag, while the system is disarmed, causes the
system to be armed in AWAY (optional HOME) mode. To
enroll / delete proximity tags, refer to figure 4.2.

D-300885 13
(First display is READY
or NOT READY)
READY 00:00
USER SETTINGS
NORMAL MODE
ENTER CODE
1. NEW INSTL CODE
2. ENROLLING
3. DEFINE ZONES
4. DEFINE PANEL
5. DEFINE COMM
[installer code]
INSTALLER MODE
ENROL WL 1WAY KP
8. DEFINE OUTPUTS
9. RECORD SPEECH
10. DIAGNOSTICS
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
<OK> TO EXIT
14. START UL/DL

[WL 1-way keypad
No. 1 to 8] (e.g. 5)
1way kp No :
1way kp No : 5 1way kp No : 5 (**)
1way kp No: 5
Enrolling a wireless
commander MCM-140+
for next
enrolling action
<OFF> TO DELETE
key until
red LED
lights
TRANSMIT NOW
Deleting a wireless
commander MCM-140+
1way kp No: 5
*
press

ENROL WL 2WAY KP
[MKP-150/MKP-151
No. 1 or 2] (e.g. 2)

2way kp No:
2way kp No : 2 2way kp No : 2 (**)
<OFF> TO DELETETRANSMIT NOW
Enrolling a wireless keypad
MKP-150/MKP-151

for next
enrolling action

ENROL WL SIREN
[WL siren No.
1 or 2] (e.g. 2)

SIREN No :
siren No : 2 siren No : 2 (**)
Momentarily press the
wireless siren self-test
button until a squawk is
heard (1 sec. approx.)
TRANSMIT NOW
Enrolling a
wireless siren
siren No: 2

for next
enrolling action
AWAY
2way kp No: 2
Deleting a wireless keypad
MKP-150/MKP-151
Press MKP-150/
MKP-151
back tamper
switch once
(see MKP-150/
MKP-151
inst. instructions) 2way kp No: 2
6. DEFINE GSM
<OFF> TO DELETE
Deleting a
wireless siren
siren No: 2
Open WL
siren cover
and remove
its battery
ENROLLING TYPE
normal enroll
by tamper
ENROLL KEYFOB
Keyfob No: -
Keyfob No: 5
<OFF> TO DELETE
KEYFOB No: 05
[Keyfob No.]
(e.g. 5)
Deleting a Keyfob
(*)
(**)
ENROLL PROX TAG
Tag No: 5
Tag No: -
PRESENT TAG
Tag No: 5
<OFF> TO DELETE
Tag No: 05Tag No: 05
(Prox tag No.)
(e.g. 5)
for next
enrolling action
Enrolling a Prox tag Deleting a prox tag
(*)
(**)
(**)
Present
tag
Optional
Keyfob No: 5
TRANSMIT NOW
KEYFOB No: 05
for next
enrolling action
Enrolling a Keyfob
(**)
ZONE No: 05
<OFF> TO DELETE
ZONE No: 05
[WL Zone No.
01-28] (e.g. 05)
(**)
Deleting wired/
WL sensor
ZONE No: 05
[Initiate transmission)
ZONE No: 05
TRANSMIT NOW
(**)
Enrolling a WL sensor
(***)
for next
enrolling action
ZONE No: 29
ZONE No: 29
Enrolling wired sensor
for next
enrolling action
[wired Zone No.
29/30] (e.g. 29)

<OK> TO ENROLL
ENROLL SENSORS
ZONE No: - -
SET SENSITIV.
higher sensitivity
lower sensitivity
Select by
or
(****)

[wired/WL Zone No.
01-30] (e.g. 05)
(press
any
key)
Figure 4.2 - Enrolling / Deleting Wireless Devices / Keyfobs / Wireless Commanders / Wireless Sirens
* Keyfob & proximity tags enrolling can be performed by
the installer or by the user (via USER SETTINGS
menu).
** A black box in the display means that a device is
enrolled (the system has learned its ID). No black box
indicates that the device is not enrolled.
*** Initiate either normal transmission or the device tamper
function (see ENROLLING TYPE, Par. 4.2.2).
****Select "higher" sensitivity for far wireless device,
"lower" for near devices.

14 D-300885
4.3 DEFINING ZONE TYPES, NAMES & CHIME ZONES
This mode allows you to assign one of 13 zone types to
each of the system's 30 (wireless & wired) zones. In
addition, it also allows you to assign a name to each zone
and determine whether the zone will operate as a chime
zone (only while the system is in the disarmed or Home
arming state). When a chime zone is triggered, chime
melody or zone name is heard (there are 3 selectable
chime modes - Melody chime, Zone Name Chime or Chime
Off).
A list of factory defaults is printed on table 1. You may fill
out the blank columns even before you start and proceed
to program according to your own list.
Remember!
A delay zone is also a perimeter zone by definition.
Zone types are fully explained in Appendix D.
Selectable Zone Names
Dining room
Downstairs
Emergency
Fire
Front door
Garage
Garage door
Guest room
Hall
Kitchen
Laundry room
Living room
Master bath
Master bdrm
Office
Upstairs
Utility room
Yard
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Attic
Back door
Basement
Bathroom
Bedroom
Child room
Closet
Den
31 zone names can be selected, 26 fixed names and 5
custom names (defined by the installer - see chap. 4.8):
Zxx: CHIME
Zone name-chime
(**)
ZONE No: - -
Zxx: TYPE -
[Zone No.] (e.g. 05)
1. Inter-follow
2. Perimeter Melody-chime
Chime off
Zxx: NAME - -
Attic
Back door
Basement
Bathroom
Bedroom
Child room
Closet
(*)
(*)
(*)
4. Delay 1
5. Delay 2
6. 24h silent
7. 24h audible
8. Fire
9. Non-alarm
10. Emergency
3. Perim-follow
(see list above)
11. Gas
12. Flood
13. Interior
(First display is READY
or NOT READY)
3. DEFINE ZONES
READY 00:00
NORMAL MODE
[installer code]
USER SETTINGS
ENTER CODE
2. ENROLLING
5. DEFINE COMM
INSTALLER MODE
<OK> TO EXIT
10. DIAGNOSTICS
8. DEFINE OUTPUTS
9. DEFINE VOICE
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
14. START UL/DL
6. DEFINE GSM
Figure 4.3 - DEFINE ZONES Flow Chart
* The currently saved option is displayed with a dark box at the right side. To review the options, repeatedly click
or button, until the desired option is displayed, then click (a dark box will be displayed
at the right side).
** Clicking the button in this location brings you to the same zone number that you are dealing with. Press
or to select the next zone.
Table 1 - DEFAULT AND PROGRAMMED ZONE DEFINITIONS
Zone Zone Type Zone Name Chime (melody
No. Default Programmed Default Programmed Zone Name or Off) (*)
1 Delay 1 Front Door
2 Delay 1 Garage
3 Delay 2 Garage Door
4 Perimeter Back Door
5 Perimeter Child Room
6 Interior Office
7 Interior Dining Room
8 Perimeter Dining Room
9 Perimeter Kitchen
10 Perimeter Living Room
11 Interior Living Room
12 Interior Bedroom
13 Perimeter Bedroom
14 Perimeter Guest Room
15 Interior Master Bedroom

D-300885 15
Zone Zone Type Zone Name Chime (melody
No. Default Programmed Default Programmed Zone Name or Off) (*)
16 Perimeter Master Bedroom
17 Perimeter Laundry Room
18 Perimeter Master Bathroom
19 Perimeter Basement
20 Fire Fire
21 Fire Fire
22 Emergency Emergency
23 Emergency Emergency
24 24 h / silent Basement
25 24 h / silent Office
26 24 h / audible Attic
27 24 h / audible Den
28 non-alarm Yard
29 non-alarm Hall
30 non-alarm Utility room
* Note: All zones are Off-chime by default. Enter your own choice in the last column and program accordingly.
4.4 DEFINING CONTROL PANEL PARAMETERS
4.4.1 Preliminary Guidance
This mode allows you to customize the control panel and
adapt its characteristics and behavior to the requirements
of the particular user. An illustrated process is shown in
figure 4.4. In this illustration, each selected option is
displayed with a dark box at the right side. To review the
options, repeatedly click or button, until
the desired option is displayed, then click SHOW/OK button.
4.4.2 Entry Delays 1&2
(Fig. 4.4, location 01, 02). Two different entry delays allow
the user to enter the protected site (while the system is in
the armed state) via 2 specific doors and routes without
causing an alarm.
Following entry, the user must disarm the control panel
before the entry delay expires. Slow-rate warning beeps
start sounding once the door is opened, until the last 10
seconds of the delay, during which the beeping rate
increases. Locations No. 1 (entry delay 1) and 2 (entry
delay 2) allow you to program the length of these delays.
Available options for each delay are: 00s, 15s, 30s, 45s,
60s , 3m and 4m.
Note: For UL installation entry delay should be up to 45 sec.
4.4.3 Exit Delay
(Fig. 4.4 location 03). An exit delay allows the user to arm the
system and leave the protected site via specific routes and
doors without causing an alarm. Slow-rate warning beeps
start sounding once the arming command has been given,
until the last 10 seconds of the delay, during which the
beeping rate increases. Location No. 3 allows programming of
the exit delay length. Available options are: 30s, 60s, 90s,
120s, 3m, 4m.
Note: For UL installation exit delay should be up to 120 sec.
4.4.4 Bell Time
(Fig. 4.4, location 04). Here you select the length of time
the bell (or siren) is allowed to function upon alarm. The
bell time starts upon activation of the siren. Once the bell
time expires, the siren is automatically shut down.
Available options are: 1, 3, 4, 8, 10, 15 and 20 minutes.
4.4.5 Abort Time
(Fig. 4.4 location 05). Here you select the length of time
allowed by the system to abort an alarm (not applicable to
alarms from FIRE, 24H SILENT, EMERGENCY, GAS and
FLOOD zones). The PowerMaxComplete is programmed to
provide an “abort interval” that starts upon detection of an
event. During this interval, the buzzer sounds a warning but
the siren remains inactive and the alarm is not reported. If
the user disarms the system within the allowed abort
interval, the alarm is aborted.
Available options are: 00s, 15s, 30s, 45s, 60s, 2m, 3m,
4m.
4.4.6 Alarm Cancel
(Fig. 4.4, location 06). Here you determine the ”cancel
alarm” period that starts upon reporting an alarm to the
central station. If the user disarms the system within that
time period, a “cancel alarm” message is sent to the
central station.
Available options are: 1, 5, 15, 60 minutes, 4hours and
also cancel inactive.
4.4.7 Quick Arm
(Fig. 4.4, location 07). Here you determine whether the
user will be allowed to perform quick arming or not. Once
quick arming is permitted, the control panel does not
request a user code before it arms the system.
The two options are: quick arm ON and quick arm OFF.
4.4.8 Bypass
(Fig. 4.4, location 08). Here you permit either manual
bypassing of individual zones (through the USER SETTINGS
menu), or allow the system to "force arm" (perform automatic
bypassing) of open zones during the exit delay. If desired,
press the arming key twice if you want to eliminate the delay
beeps that continue during a force arming. If a zone is open
and forced arming is not permitted, “NOT READY” is
displayed and the system does not arm (the “Sad Melody” will
sound). If "no bypass" is selected, neither manual bypassing
nor force arming is allowed.
Options: manual bypass, force arm and no bypass.
4.4.9 Exit Mode
(Fig. 4.4, location 09). Here you determine whether the exit
delay will restart if the exit / entry door is reopened before
the exit delay expires. Restarting the exit delay is helpful if
the user re-enters immediately after going out to retrieve
an item that he left behind. Three types of exit mode are
available:
Restart Exit - Exit delay restarts when the door is
reopened during exit delay. The restart occurs once only.
Off by door - When the door is closed, the exit delay is
automatically terminated (even if the defined exit delay
was not completed).
Normal - The exit delay is exactly as defined, regardless
of whether the door is open or closed.

16 D-300885
4.4.10 Piezo Beeps
(Fig. 4.4, location 10). Here you determine whether warning
beeps will sound or muted during exit and entry delays. An
additional option is to mute the warning beeps only when the
system is armed “HOME”.
Options: enable beeps, off when home and disable beeps.
4.4.11 Trouble Beeps
(Fig. 4.4, location 11). Under trouble conditions, the
sounder emits a series of 3 short beeps once per minute.
Here you determine whether this special beeping
sequence will be active, inactive, or just inactive at night
(the range of “night” hours is defined in the factory). The 3
options are: enable beeps, off at night (8 PM through 7
AM) and disable beeps.
4.4.12 Panic Alarm
(Fig. 4.4, location 12). Here you determine whether the
user will be allowed to initiate a panic alarm by
simultaneous pressing either the two panic buttons (on
the keypad / wireless commander) or away + home (on a
keyfob transmitter). Audible panic activates the siren and
simultaneously transmits a message via telephone. Silent
panic only transmits a message via telephone. The
options are: silent panic, audible panic and disable
panic.
4.4.13 Swinger Stop
(Fig. 4.4, location 13). Here you determine how many times
each zone is allowed to initiate an alarm within a single
arming period (including tamper & power failure events of
detectors, PowerMaxComplete and wireless siren). If the
alarms number from a specific zone exceeds the
programmed number, the control panel automatically
bypasses the zone to prevent recurrent siren noise and
nuisance reporting to the central station. The zone will be
reactivated upon disarming, or 48 hours after having been
bypassed (if the system remains armed).
Available options are: shut after 1, shut after 2, shut
after 3 and no shutdown.
4.4.14 Cross Zoning
(Fig. 4.4, location 14). Here you determine whether cross
zoning will be active or inactive. Cross zoning is a method
used to counteract false alarms - an alarm will not be
initiated unless two adjacent zones are violated within a
30-second time limit.
This feature is active only when arming AWAY and only
with zone couples from zone No. 18 to 27 (18 and 19, 20
and 21, etc.). You may use any one of these zone couples
to create a “cross-zoned” area.
Note: If one of two crossed zones is bypassed (see Para.
4.4.8), the remaining zone will function independently.
Note: Every 2 crossed zones must be of the allowed zone
type (Interior, Perimeter, Perimeter follower).
The options are: cross zone ON and cross zone OFF.
Cross zoning is not applicable in Entry/ Exit zones and
24h zones (Fire, Emergency, 24h audible, 24h silent).
4.4.15 Supervision
(Fig. 4.4, location 15). Here you determine the time limit for
reception of supervision reports from various supervised
wireless devices. If any device does not report at least once
within the selected time limit, an “INACTIVITY” alert is
initiated. The options are: 1, 2, 4, 8, 12 hours and disable.
4.4.16 NOT READY
(Fig. 4.4, location 16). Here you determine if the system will be
NOT READY status when there is a supervision failure. In the
"in supervision" mode, the system will be in NOT READY
status if during the last 20 minutes a supervision message
was not received. Options: normal and in supervision.
4.4.17 AUX Button A
(Fig. 4.4, location 17). Here you select the function of the
AUX button on keyfob transmitters and wireless
commanders MCM-140+. Four options are offered for
each AUX button:
Status (applicable only to control panel that includes voice
option):Pressing the AUX button will cause the control
panel’s voice module to announce the system status.
Instant: Pressing the AUX button while the exit delay is in
progress will cause the system to arm “instant” (the entry
delay is canceled).
Skip exit delay: Pressing the AUX button will immediately
cause the system to arm “instant”.
PGM: Pressing the AUX button will activate the PGM
output (see further programming under “DEFINE
OUTPUTS”, par. 4.8).
4.4.19 Jam Detect
(Fig. 4.4, location 19). Here you determine whether
jamming (interfering trans- missions, on the radio channel
used by the system) will be detected and reported or not.
If a jam detection option is selected, the system does not
allow arming under the relevant jamming conditions.
Jam Detection Options
Option Detection and Reporting when
UL (20/20)
(USA standard) There is continuous 20 seconds of jamming
EN (30/60)
(Europe standard) There is an accumulated 30 seconds of jamming within 60 sec.
class 6 (30/60)
(British standard) Like EN (30/60) but the event will be reported only if the jamming duration
exceeds 5 minutes.
Disabled (no jamming detection and reporting).
4.4.20 Latchkey
(Fig. 4.4, location 20). Here you determine whether the
system can be armed in the latchkey mode. If the system
is armed this way, a “latchkey” message will be sent to
specific telephones upon disarming by a “latchkey user”
(users 5-8 or keyfob transmitters 5-8). This mode is useful
when parents at work want to be informed of a child’s
return from school. You can record a name for latchkey
users.
The options are: Latchkey ON and Latchkey OFF.
4.4.21 “Not Active”
(Fig. 4.4, location 21). Here you determine the time limit for
reception of signals from sensors used to monitor the
activity of sick, elderly or disabled people. If no device
detects and reports movement at least once within the
defined time limit, a “not-active” alert is initiated.
Options: 3, 6, 12, 24, 48, 72 hours and no act disable.

D-300885 17
4.4.22 Back Light
(Fig. 4.4, location 22). Here you determine whether the
keypad back lighting will remain on at all times or will come
on when a key is pressed and go off within 10 seconds if
no further keystrokes are sensed.
The two options are: always on and off after 10 s.
4.4.23 Duress
(Fig. 4.4, loc. 23). A duress alarm (ambush) message can
be sent to the central station if the user is forced to disarm
the system under violence or menace. To initiate a duress
message, the user must disarm the system with the duress
code (2580 by default). Here you can change the code
digits or enter "0000" to disable the duress feature. The
system does not allow the user to program the duress
code saved in this memory location as an existing user
code.
4.4.24 Piezo Siren
(Fig. 4.4, location 24). Here you determine whether the
internal siren will sound or remain silent upon alarm
(according to the user preference). Options: piezo siren
on, piezo siren off.
4.4.25 Reset Option
(Fig. 4.4, location 25) (Not applicable in the USA)
Here you determine whether the system can be rearmed
(after an event) by the user or only by the installer.
Options: user reset or engineer reset.
If Engineer Reset is selected, the system can be rearmed
only by the installer; by entering and exiting the installer
menu, by entering and exiting the event log (see section 7),
or by remote telephone. To perform Engineer Reset via the
telephone, establish communication with the
PowerMaxComplete (see user guide, par. 6.3A, steps 1-5)
and continue as follows:
a. [*], [installer code], [#]
b. Wait for 2 beeps
c. [*], [1], [#]
d. [*], [99], [#]
4.4.26 Tamper Option
(Fig. 4.4, location 26). Here you determine whether zone
tamper will be reported or ignored. Available options are:
zone tamper ON and zone tamper OFF.
4.4.27 Siren On Line
(Fig. 4.4, location 27). Here you determine whether the siren
will be activated or not when the telephone line fails during
system armed state. Available options are: enable on fail,
disable on fail.
4.4.28 Memory Prompt
(Fig. 4.4, location 28). Here you determine whether the user
will receive indication that an alarm has been activated.
Available options are: enable and disable.
4.4.29 Disarm Option
(Fig. 4.4, location 29). Here you determine when it is possible
to disarm the system:
A. Any time.
B. In AWAY mode, during entry delay, by using the
PowerMaxComplete keypad or wireless device (keyfob).
C. In AWAY mode, during entry delay, by using a wireless
device (keyfob) only (this is set as a default in UK to
comply with DD423).
D. During entry delay, or by using the PowerMaxComplete
keypad in AWAY mode.
Options: any time, on entry all, on entry wireless, or
entry + away kp.
4.4.30 Bell/Rep. Option
(Fig. 4.4, location 30). Here you determine whether an
alarm will be initiated (siren / report) when there is a
supervision / jamming failure during AWAY arming state.
Available options are: EN standard and other. When "EN
standard" is selected, if there is supervision / jamming
failure during AWAY arming, the siren is activated and the
events are reported as tamper events. When "Other" is
selected, there is no such activity during AWAY arming.
4.4.31 Low-Bat Ack
(Fig. 4.4, location 31). Here you determine whether the user
will hear or will not hear low battery sound when he tries to
disarm the system with a keyfob whose battery voltage is
low.
Available options are: keyfob L-B on (the user has to
acknowledge the keyfob low battery message) or keyfob
L-B off (the user does not have to acknowledge the keyfob
low battery message).
4.4.32 Screen Saver
(Fig. 4.4, location 32). Here you can determine that if no
key is pressed during more than 30 seconds, the display
will be “PowerMax” (to prevent possible intruder of
knowing the system status). You can determine that
normal display will return after pressing the button
followed by entering user code (Refresh by Code) or after
pressing any key (Refresh by Key).
If Refresh by Key is selected, the first pressing of any key
(except Fire and Emergency) will cause normal display
return and the second press will perform the key function.
Regarding the Fire and Emergency keys, the first key
press will cause normal display return and also will perform
the Fire/Emergency function.
Options: scrn saver OFF, refresh by code, refresh by key.
4.4.33 Confirm Alarm
(Fig. 4.4, location 33). Here you determine that if 2
successive alarms will occur during a specific period, the
second alarm will be considered as a confirmed alarm
(for confirmed alarm reporting, see par. 4.5.12 REPORT
CNF ALARM).
Options: disable 30 min, 45 min, 60 min, or 90 min.
4.4.34 AC FAIL REP
(Fig. 4.4, location 34). Here you determine the time interval
between AC power failure occurrence and the failure
reporting. Options: 5 minutes, 30 minutes, 60 minutes or
180 minutes.
4.4.36 User Permission
(Fig. 4.4, location 36). Here you determine whether the
access to the INSTALLER MODE requires user permission.
If you select ENABLE, the installer mode will be accessible
only through the user menu after entering the user code.
Options: Enable, Disable.
4.4.38 Batttery Type
(Fig. 4.4, location 38). Here you determine which type of
battery pack is used, so that the system will supply proper
charge current.
Options: 7.2V or 9.6V.

18 D-300885
READY 00:00
USER SETTINGS
NORMAL MODE
ENTER CODE
1. NEW INSTL CODE
2. ENROLLING
3. DEFINE ZONES
5. DEFINE COMM
[installer code]
INSTALLER MODE
05: ABORT TIME
09: EXIT MODE
13: SWINGER STOP
17: AUX BUTTON A
status
instant
01: ENTRY DELAY 1 02: ENTRY DELAY 2 03: EXIT DELAY 04: BELL TIME
06: ALARM CANCEL 07: QUICK ARM
quick arm ON
quick arm OFF
08: BYPASS
manual bypass
no bypass
force arm
10: PIEZO BEEPS 11: TROUBLE BEEPS 12: PANIC ALARM
cross zone ON
cross zone OFF
14: CROSS ZONING 15: SUPERVISION
superv time 1 h
superv time 2 h
superv time 4 h
superv time 8 h
16: NOT READY
normal
in supervision
4. DEFINE PANEL
entry dly2 00 s
entry dly2 15 s
entry dly2 30 s
entry dly2 45 s
entry dly2 60 s
entry dly2 3 m
entry dly2 4 m
exit delay 30 s
exit delay 60 s
exit delay 90 s
exit delay 120 s
exit delay 3 m
exit delay 4 m
bell time 1 m
bell time 4 m
bell time 8 m
bell time 10 m
bell time 15 m
bell time 20 m
cancel time 1 m
cancel time 5 m
cancel time 15 m
cancel time 60 m
cancel time 4 h
cancel inactive
enable beeps
off when home
disable beeps enable beeps
off at night
disable beeps silent panic
audible panic
disable panic
shut after 1
shut after 2
shut after 3
no shutdown superv time 12 h
disable
PGM
entry dly1 00 s
entry dly1 15 s
entry dly1 30 s
entry dly1 45 s
entry dly1 60 s
entry dly1 3 m
entry dly1 4 m
abort time 00 s
abort time 15 s
abort time 30 s
abort time 45 s
abort time 60 s
abort time 2 m
abort time 3 m
restart exit
off by door
normal
bell time 3 m
abort time 4 m
Note: The currently saved
options are displayed with
dark box at the right side of
the display. To review the
options, repeatedly click
or until the
desired option is displayed,
then click OK (a dark box
will be displayed at the right
side).
Note: Force arm is not
applicable to the UK.
6. DEFINE GSM
in
USA
in
USA
in
USA in USA
8. DEFINE OUTPUTS
9. DEFINE VOICE
10. DIAGNOSTICS
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
<OK> TO EXIT
14. START UL/DL
skip exit delay
19: JAM DETECT
UL (20/20)
EN (30/60)
class 6 (30/60)
disabled
21: NOT ACTIVE
no act time 3 h
no act time 6 h
no act time 12 h
no act time 24 h
no act time 48 h
no act time 72 h
no act disable
22: BACK LIGHT
always on
off after 10 s
23: DURESS
duress code 2580
(Change the code or
enter 0000 to disable
duress function)
Note: Duress code is not
applicable to the UK.
24: PIEZO SIREN
piezo siren on
piezo siren off
25: RESET OPTION
user reset
enginner reset
Not applicable
in the USA
26: TAMPER OPTION
zone tamper on
zone tamper off
27: SIREN ON LINE
enable on fail
disable on fail
28:MEMORY PROMPT
enable
disable
29: DISARM OPTION
any time
on entry wrless
entry + awake kp
on entry all
Not applicable
in the USA in
UK
30: BELL/REP. OPT
EN standard
other
31: LOW-BAT ACK
keyfob L-B on
keyfob L-B off
32: SCREEN SAVER
scrn saver OFF
refresh by code
refresh by key
34: AC FAIL REP
5 minutes
30 minutes
60 minutes
180 minutes
33: CONFIRM TIME
disable
30 minutes
45 minutes
60 minutes
90 minutes
20:LATCHKEY
latchkey on
latchkey off
(*)
36: USER PERMIT
Disable
Enable in
UK
38: BATTTERY TYPE
7.2V
9.6V
Figure 4.4 - DEFINE PANEL Flow Chart

D-300885 19
4.5 DEFINING COMMUNICATION PARAMETERS
Preliminary Guidance
This mode allows you to adapt the telephone
communication parameters to the local requirements.
Compatible central station receivers are:
Osborne-Hoffman model 2000, Ademco Model 685,
FBII Model CP220, Radionics Model D6500, Sur-Gard
Model SG-MLR2-DG and Silent Knight Model 9500.
IMPORTANT: In telephone / pager number locations and
account number locations, you may be required to enter
hexadecimal digits. In telephone number locations, these
digits are used as codes to control the dialer:
Hex.
Digit Keying Sequence Code Significance
A <#>
⇒
<0> Applicable only at the beginning of a
number - the dialer waits 10 seconds
or waits for dial tone, whichever
comes first and then dials.
B <#>
⇒ <1> Inserts an asterisk (J)
C <#>
⇒
<2> Inserts a pound sign (#)
D <#>
⇒
<3> Applicable only at the beginning of a
number - the dialer waits 5 seconds
for dial tone and goes on hook if none
is received.
E <#>
⇒
<4>
A
pplicable only in the middle of the
number - the dialer waits 5 seconds
F <#>
⇒
<5> Not applicable in phone numbers
To enter a series of digits, use the following keys:
<Numeric keypad> - to enter the number
- moves the cursor from left to right
- moves the cursor from right to left
- deletes everything after the cursor (to the right).
4.5.1 Autotest Time
(Fig. 4.5, location 01). Here you determine the time at which the
telephone line will be tested and reported to the central station.
4.5.2 Autotest Cycle
(Fig. 4.5, location 02). Here you determine the time interval
between consecutive telephone line test messages sent to
the central station. The control panel performs this at
regular intervals to verify proper communications.
The options are: test every 5 hours, test every 1, 5, 7, 14,
30 days and test off.
4.5.3 Area Code
(Fig. 4.5, location 03). Here you enter the system tel. area
code (up to 4 digits).
4.5.4 Out Access No
(Fig. 4.5, location 04). Here you enter the number that is used
as a prefix to access an outside telephone line (if exists).
4.5.5 First Central Station Tel.
(Fig. 4.5, loc. 05). Here you program telephone number of the 1st
central station (including area code, 16 digit max) to which
the system will report the event groups defined in memory
location 11 (see note in Fig. 4.5).
4.5.6 First Account No.
(Fig. 4.5, location 06). Here you enter number that will
identify your specific alarm control system to the first
central station. The number consists of 4 or 6 hexadecimal
digits (see note in Fig. 4.5).
4.5.7 2ND Central Station Tel
(Fig. 4.5, loc. 07). Here you program telephone number of the
2nd central station (including area code, 16 digit max) to which
the system will report the event groups defined in memory
location 11 (see note in Fig. 4.5).
4.5.8 Second Account No.
(Fig. 4.5, loc. 08). Here you enter number that will identify
your system to the 2nd central station. The account number
consists of 4 or 6 hexadecimal digits (see note in Fig. 4.5).
4.5.9 Report Format
(Fig. 4.5, location 09). Here you select the reporting format
used by the control panel to report events to central stations
(see note in figure 4.5).
The options are: Contact-ID SIA 4/2 1900/1400 
4/2 1800/2300 Scancom (see Appendix C - code lists).
4.5.10 4/2 Pulse Rate
(Fig. 4.5, location 10). Here you select the pulse rate at
which data will be sent to central stations if any one of the
4/2 formats has been selected in Location 09 REPORT
FORMAT (see note in Fig. 4.5). The options are: 10, 20,
33 and 40 pps.
4.5.11 Reporting to Central Stations
(Fig. 4.5, location 11) (see note in Fig. 4.5).
Here you determine which types of event will be reported
to central stations. Due to lack of space in the display,
abbreviations are used: alarm is “alrm”, alert is “alrt” and
open/close is “o/c”. The asterisk (J) is a separator
between events reported to central station 1 and events
reported to central station 2.
Messages are divided by type into three groups:
GROUP EVENTS REPORTED
Alarms Fire, Burglary, Panic, Tamper
Open/Close Arming AWAY, Arming HOME, Disarming
Alerts No-activity, Emergency, Latchkey
"Alarm" group has the highest priority and "Alert" group
has the lowest priority.
The selectable options are as follows:
Plan name Sent to center
1 Sent to center 2
all -o/c Jbackup All but open/close All but open/close if center 1
doesn’t respond
all Jall All All
all-o/c Jall -o/c All but open/close All but open/close
all –o/c Jo/c All but open/close Open/close
all (–alrt) Jalrt All but alerts Alerts
Alrm Jall (–alrm) Alarms All but alarms
Disable report Nothing Nothing
all Jbackup All All if cent. 1 doesn’t respond
Note: “All” means that all 3 groups are reported and also
trouble messages - sensor / system low battery, sensor
inactivity, power failure, jamming, communication failure etc.
4.5.12 Report CNF Alarm
(Fig. 4.5, location 12). Here you determine whether the
system will report whenever 2 or more events (confirmed
alarm) occur during a specific period (see par. 4.4.33 and
note in figure 4.5).
Available options are: enable report, disable report,
enable + bypass (enabling report and bypassing the
detector - applicable to PowerMaxComplete that is
compatible with DD423 standard).
4.5.13 Send 2WV Code
(Fig. 4.5, location 13). Here you determine whether the
system will send two-way voice code to the central station
(to turn the central station from data communication to voice
communication state) by using pre-selected SIA or Contact-
ID communication format only (see note in Fig. 4.5).
Options: send and don't send.

20 D-300885
4.5.14 Two-Way Voice Central Stations
(Fig. 4.5, loc. 14). (See note in Fig. 4.5) - Optional -
applicable only in PowerMaxComplete that includes
"voice" feature.
Here you select the timeout for 2-way voice
communication with Central Stations, or enable the central
station to ring back for 2-way voice function. This option is
applicable only after reporting an event to the central
station. (The central station person can press [3] for listen-
in", [1] for "speak out" or [6] for listening and speaking).
The options are: 10, 45, 60, 90 seconds, 2 minutes, ring
back and disable (no two-way voice communication).
Note: If "Ring Back" is selected, you should select
"Disable Report" for private telephone (see par. 4.5.20 -
Reporting to Private Telephones), otherwise the central
station will establish communication with the
PowerMaxComplete (after an event occurrence) in the
normal manner (and not after one ring).
4.5.15 Ring Back Time
(Fig. 4.5, location 15). Here you determine the period during
which the central station can establish 2-way voice
communication with the PowerMaxComplete (after 1 ring), if:
A. Alarm type message was received by central station.
B. Ring Back function was selected (see par. 4.5.14).
The options are: 1, 3, 5or 10 min. (see note in Fig. 4.5).
4.5.16 Dialing Attempts
(Fig. 4.5, location 16). Here you determine how many
times the communicator will dial the central station’s
number. (see note in Fig. 4.5).
The options are: 2, 4, 8, 12, and 16 attempts.
Attention! A maximum of 2 dialing attempts is permitted
by the Australian Telecommunication Authority.
For UL installation, dialing attempts should be not less
than 5 and not more than 10 attempts.
4.5.17 Set Private Tel. No.
(Fig. 4.5, location 17). Here you program the four
telephone numbers (including area code) of the private
subscriber to which the system will report the event groups
defined in Location 20.
4.5.18 Two-Way Voice - Private Phones
(Fig. 4.5, location 18) - Optional - applicable only in
PowerMaxComplete that includes "voice" feature.
Here you determine whether 2-way voice communication
with private telephones will be allowed or not.
The two options are: enable 2-way and disable 2-way.
4.5.19 Private Tel. Dialing Attempts
(Fig. 4.5, location 19)
Here you determine how many times the communicator will
dial the called party’s number (private telephone).
The options are: 1, 2, 3 and 4attempts.
Attention! A maximum of 2 dialing attempts is permitted
by the Australian Telecommunication Authority.
4.5.20 Reporting to Private
Telephones
(Fig. 4.5, location 20)
Here you determine which event groups will be reported to
private telephone subscribers. The options are as follows:
Term Description
all All messages
all (-op/cl) All messages, except open/close
all (-alerts) All messages, except alerts
alarms Alarm messages
alerts Alert messages
op/cl Open/close
disable report No message will be reported
Note: “All” means all events including the L. BAT and AC
FAIL trouble messages.
4.5.21 Tel. Acknowledge
(Fig. 4.5, location 21). Here you determine whether the
system will use the single acknowledge or the all
acknowledge mode when reporting to private telephones.
Note: In the single acknowledge mode, receiving an
acknowledge signal from a single telephone is sufficient to
consider the current event closed and call off the
communication session. The remaining telephones serve
for backup purposes only. In the all acknowledge mode, an
acknowledge signal must be received from each telephone
before the current event is considered reported.
The options are: single ack and all ack.
4.5.22 Pager Tel. No.
(Fig. 4.5, location 22). Here you program the telephone
number (including area code) of the pager to which the
system will report (if any).
4.5.23 Pager’s PIN No.
(Fig. 4.5, location 23). Here you enter the pager’s PIN
code - a digital sequence that is the pager’s address. The
paging company’s computer needs this input for routing
messages to the specific pager. The PIN sequence
precedes any digital message that the PowerMaxComplete
sends to the pager to report an event. It may include digits,
pauses and special characters (
∗ or #). Call the paging
company to find out what the pager’s PIN code should
consist of.
Important! In this location, special characters can be
entered as shown below:
To Insert Keying Sequence Character Displayed
∗ <#>
⇒ <1> B
# <#>
⇒
<2> C
5 sec pause <#>
⇒
<3> E
Enter the pager’s PIN number (up to 16 digits, including
special characters, depending on pager system protocol).
4.5.24 Reporting to a Pager
(Fig. 4.5, loc. 24). Here you determine which event groups
will be reported to the pager. (For the abbreviations, refer
to par. 4.5.11).
The options are: all alarms + alerts all (- op/cl) 
trbl + op/cl trbl op/cl disable report
4.5.25 Recent Closure
(Fig. 4.5, location 25). Here you enable or disable the
“recent closing” report, that is sent to the central station if
an alarm occurs within 2 minutes from the expiry of the exit
delay.
The options are: recent close ON and recent close OFF.
4.5.26 Remote Access
(Fig. 4.5, location 26). Here you give or deny permission to
access the system and exercise control from a remote
telephone.
The options are: rem. access ON and rem. access OFF.
4.5.27 Mast. DL Code
(Fig. 4.5, location 27). Here you determine the master
installer 4-digit password for downloading/uploading data
into/from the PowerMaxComplete memory. (See note in
Fig. 4.5).
Attention! If "0000" is used, it will not enable connection of
the PowerMaxComplete to the PC for upload/download
purpose.