Vivo BEE-V002E User manual

Electric Two Frame Stainless Steel Honey Extractor
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/bee-v002e
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: BEE-V002E

2
If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not
exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
WARNING: IMPORTANT SAFETY INFORMATION
READ AND FOLLOW ALL SAFETY REQUIREMENTS
PREPARATION
1. Aer carefully removing the machine from the packing carton, remove
all protective film and clean the honey extractor thoroughly with mild
soap and water BEFORE first use.
2. The honey extractor should be placed on a dry, flat stable surface
KEEP THIS MANUAL IN A SAFE AND DRY PLACE FOR FUTURE REFERENCE
MACHINE STRUCTURE
Clear Lids
Honey Extractor
Drum
Wing Nut
Honey Gate with
Lid and O Ring
Leg Bolt
Leg
CAUTION: SHARP EDGES

3
PACKAGE CONTENTS
1 (x1) Honey Extractor
2 (x1) Honey Gate with Lid
3 (x1) Hex Nut (on Honey Gate)
4 (x1) O Ring (Pre-installed on Honey Gate)
5 (x3) Leg
6 (x6) Leg Bolt
7 (x6) Washer
8 (x2) Lid (with a Safety Switch)
9 (x12) M4 Bolt
10 (x12) M4 Nut
11 (x3) Stability Bolt
STEP 1
Attach legs to extractor using the included bolts (6) and washers (7).
ASSEMBLY STEPS

4
STEP 2
To install honey gate, remove large hex nut from gate piece. Insert gate through
the front side hole and secure backside with hex nut (tighten enough to seal O
ring).
STEP 3
Close both lids to engage safety
switches. Flip the power switch to
the on (I) position, and turn the dial
until the basket is spinning at the
desired speed. Each lid has a built
in safety switch that will cut power
the moment it is opened, and power
will not be restored until both lids
are closed. Turn the dial back to “0”
when frames have been emptied
and remove the frames from the
extractor.

5
STEP 4
Extractor is ready to operate. (see Operating Instructions)
STEP 5
If needed, adjust coupling using the attached bolts.
STEP 6
(Optional) Bolt feet down to floor or surface for added stability (hardware
included).

6
Once the frames have been emptied on one side, remove the
frames, turn the frames around, and place them back in the
extractor. Repeat step 2, then remove the frames from the
extractor.
STEP 4
With the drain positioned over a bucket or other container, open
the honey gate to begin draining honey. Tip the extractor forward
to drain as much honey as possible.
STEP 5
OPERATING INSTRUCTIONS
With the control dial set to “0” and power switch set to o (O),
plug the power cord into a standard AC wall outlet.
STEP 1
STEP 2 Place honey frames in extractor basket. Load two sides to keep
extractor balanced as this will reduce any possible shaking.
STEP 3 Close both lids to engage safety switches. Flip the power switch
to the on (I) position, and turn the dial until the basket is spinning
at the desired speed. The front lid has a built in safety switch that
will cut power the moment it is opened, and power will not be
restored until lid is closed. Turn the dial back to “0” when frames
have been emptied and remove the frames from the extractor.
DISASSEMBLY
To disassemble the extractor, remove the four cap nuts on the top of the extractor
(two on each side), then pull the top brace up and o. The basket can then be lied
out.
A steel ball bearing rests below the basket sha to improve rotation. Set this aside in
a safe place (such as a cup) so it does not roll away and become lost.
WARNING: KEEP HANDS CLEAR OF MOVING
PARTS TO REDUCE RISK OF INJURY

7
WARRANTY
We oer a ONE YEAR warranty for this product. If you have any problems with the
machine, please contact us directly. We have a 30 Day Return Policy.
CARE & MAINTENANCE
QUICK CLEANING
Option 1: Rinse extractor out with cold water from a hose. If available, a pressure
washer is very eective. Empty excess water to prevent possible surface rust.
Option 2: Place open extractor next to hive. Bees will clean it out and use the
materials.
IN-DEPTH CLEANING
Disassemble extractor (see Disassembly instructions). Using mild dish soap and
warm water, scrub drum and basket clean. Completely rinse the parts and dry with a
so cloth. Reassemble the extractor when dry.
NOTE: PLEASE AVOID GETTING MOTOR AND CONTROLLER WET AS THE ELECTRONIC
COMPONENTS ARE NOT FULLY WATERPROOF
CARE
• When not in use, store the extractor in a dry place. Although stainless steel
is highly resistant to rust and corrosion, light surface rust can form in wet
conditions.
• If surface rust forms, clean with a light abrasive to remove rust.
• If the extractor begins making squeaking noises, lightly lubricate all bearings
with a food safe grease or oil. Wipe away any excess.
• If the roller bearing in the crank sha support block does not turn freely,
lubricate with a light grease (such as white lithium) or oil.
• The gearbox is permanently sealed and requires no maintenance.

Last Updated: 06/20/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654