Vivo DESK-E155TN User manual

Vintage Brown / Black 55" x 24" Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e155tn
SKU: DESK-E155TN
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Drive Rod
B x1)
Motor
C(x2)
Liing Column
D(x1)
Desktop
E(x1)
Sync Rod
F(x1)
Upper Crossbar
G (x1)
Adapter Holder
H x1)
AC Adapter
I(x1)
Crossbar
J(x1)
Power Cord
K(x1)
Controller
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x4)
M8x10 Hex
Head Screw
S-B x4)
M5x60 Hex
Head Screw
S-C (x6)
M6x35 Philips
Head Screw
S-D (x5)
ST3.5x13 Philip
Head Screw
S-E (x4)
M5x8 Philips
Head Screw
S-F (x6)
Washer
S-G x3)
Cable Clip
S-H (x9)
Silicone Pad
S-I (x1)
4mm Allen
Wrench
S-J (x1)
5mm Allen
Wrench
S-K (x1)
8mm Allen
Wrench

3
8m m
S- K
Le ft E nd Righ t En d
Phillips
Sc rew driv er
S- E
C
S- K
A
B
S- H
S- H
88lbs
(40kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Insert the le (short) end of the drive rod (A) into the right side of a liing column (C). Slide the
motor (B) onto the right (long) end of the drive rod, using the 8mm Allen wrench (S-K) to align the
sockets if needed, and secure to the column using the M5x8 Phillips head screws (S-E) with a Phillips
screwdriver. Apply x3 silicone pads (S-H) evenly to the top bar of each liing column.
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
Drive Rod
Upper Crossbar

4
STEP 2
Place the desktop (D) upside down on a flat surface. Assemble the liing columns (C) to the desktop
using x6 M6x35 Phillips head screws (S-C) with washers (S-F) and tighten with a screwdriver.
STEP 3
Loosen the knobs on the sync rod (E) and slide the socket end onto the drive rod. While holding the
sync rod with one hand, extend the hex sha into the non-motorized leg, using the 8mm Allen wrench
(S-K) to align the socket if needed. Tighten both knobs.
Phillips
Sc rewd rive r
C
D
S- C
S- F
E
S- K
8m m
S- K
Co ncave S ide Co nvex S ide
loosen loos en
Socket End Hex Sha

5
STEP 4
Attach the adapter holder (G) and x3 silicon pads to the upper crossbar (F).
Mount the upper crossbar to the liing columns using M5x60 hex head screws
(S-B) and tighten using the 4mm Allen wrench (S-I).
STEP 5
Assemble the crossbar (I) to the back of the liing columns using M8x10 hex head screws (S-A) and
tighten with the 5mm Allen wrench (S-J).
STEP 6
Mount the controller (K) to the underside of the desktop using ST3.5x13 screws (S-D) and tighten with
a screwdriver or drill.
4m m
S- I
F
S- I
S- B G
S- H
S- H Stick th e 3 Si lico ne P ad s
t o th e cr ossbar, and
make s ure th e si lico ne p ads
are fa cing d ow n w hen
assemb ling t he c rossbar
to t he d esktop.
S- H
S- D
K
Dr ill
Apply the silicone pads
(S-H) to the crossbar,
making sure they are facing
down when assembling the
crossbar to the desktop.
IS-A
S- J
5m m
S- J

6
STEP 7
Slide the AC adapter (H) into the adapter holder, making sure the connector cable is on the same side
as the controller.
STEP 8
Connect the AC adapter to the controller, then connect the controller to the motor.
Plug the power cord (J) into the AC adapter. Use the cable clips (S-G) to organize
the cables. Clips are held in place using adhesive pads, but may be secured using
ST3.5x13 screws (S-D) for extra security (drill pilot holes with 1/8” bit).
H
S- G S- D
K
B
J
H

7
STEP 9
Carefully flip the assembled desk right side up and plug the power cord into an AC electrical outlet. If
necessary, adjust foot pads to level the desk.
The desk is now ready for use. Please refer to the Controller User Guide for operational instructions.
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
CAUTION!
Bu bb le L ev el
Bubble Level

LAST UPDATED: 02/02/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303