Vivo Blue Kids DESK-V303B User manual

Blue Kids’ Height Adjustable Desk and Chair
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v303b
SKU: DESK-V303B
[email protected]om www.vivo-us.com 309-278-5303

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING!
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF DESK OR CHAIR
• USE TIPOVER RESTRAINT OR ANCHOR DESK TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
B1 (x1)
Chair Leg
B2 (x4)
Feet
B4 (x1)
Side Support Bar
B5 (x1)
Center Support
Bar
B6 (x1)
Seat Bottom
B3 (x1)
Support Bar
B8 (x1)
Desktop
B9 (x1)
Desk Leg
B10 (x1)
LED Lamp
B7 (x1)
Seat Back
A1 (x8)
Lock Washer
A3 (x8)
Plastic Washer
A4 (x4)
1" Screw
A5 (x2)
Knob
A2 (x12)
M6x20
A6 (x4)
M6x40
A8 (x1)
Allen Wrench
A7 (x1)
Hook
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
Phillips
Screwdriver

3
ASSEMBLY STEPS
STEP 1
Adjust sides of chair legs (B1) to equal length.
Place chair legs in feet (B2), making sure legs
are fully seated in openings.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
165lbs
(75kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 220lbs
(100kg)
DESK CHAIR
STEP 2
Secure feet using x4 M6x20 screws (A2) and x4
lock washers (A1). Tighten with Allen wrench
(A8).
STEP 3
Assemble right side support bar (B3) to leg
using x2 M6x20 screws (A2) and x2 plastic
washers (A3), making sure the back of the bar
faces in the same direction as the long ends of
the feet. The support bar has a large hole on
the le side which will face inward. Tighten
with Allen wrench.
STEP 4
Slide center support bar (B5) into large hole
on right side bar. Slide le side support bar
(B4) onto center bar, and secure to legs with x2
M6x20 screws (A2) and x2 plastic washers (A3).
Tighten with Allen wrench.

4
STEP 5
Mount plastic seat bottom (B6)
to assembled chair frame using
1” screws (A4). Tighten with
Phillips screwdriver.
STEP 6
Slide plastic seat back (B7) onto chair frame,
aligning upper or lower holes in seat back with
screw holes in frame depending on the needed
height.
STEP 7
Secure seat back using knobs (A5).
STEP 8
Adjust chair feet to sit level if needed.
STEP 9
Adjust sides of desk legs (B9) to equal length. Place desk legs in
feet (B2), making sure legs are fully seated in openings.

5
STEP 10
Secure feet using x4 M6x20 screws (A2) and x4 lock
washers (A1). Tighten with Allen wrench (A8).
STEP 11
Assemble desktop (B8) to legs using M6x45 screws (A6) and
x4 plastic washers (A3), making sure the front of the desktop
faces in the same direction as the long ends of the feet.
Tighten with Allen wrench.
STEP 12
Squeeze sides of hook (A7) and fit into slot on le or right side of desk.

6
STEP 13
Adjust desk feet to sit level if needed. Place lamp (B10) into le side hole in desktop. Connect power
adapter to lamp and plug into wall outlet.
STEP 14
Loosen knobs on sides of desk to adjust desktop tilt angle, and tighten knobs to secure position.
CAUTION: Do not grip the back of the desktop when adjusting tilt angle. Grip sides of desktop for
safer adjustment.
Lamp Operation: Touch power button to
turn lamp on. Touch button again repeatedly
to change brightness (low, medium, high). To
turn lamp o, hold power button.

7
Height Adjustment
RAISE:
Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it
reaches desired height. Repeat with chair.
LOWER:
Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it
reaches max height. Slowly lower down to desired height. Repeat with chair.
To avoid injury due to
falling, do not lean the
chair backwards or to
the sides while sitting.
Remove large or unstable
objects before tilting the
desktop.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.

LAST UPDATED: 09/16/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M