Vivo DESK-V102EW User manual

White Electric Single Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v102ew
SKU: DESK-V102EW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
PACKAGE CONTENTS
WARNING!
A (x1)
Telescopic
Crossbar
B(x1)
Sync Rod
C(x1)
AC Adapter
S-A (x16)
M6x12mm
Bolt
S-B x10)
7/8" Screw
S-C (x2)
3/4" Screw
S-D (x1)
Allen Key
H(x1)
Leg
D (x1)
Shelf
E (x2)
Side
Bracket
F (x2)
Foot
G (x2)
Hook
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
S-E (x3)
Cable Clip
S-F (x8)
Rubber
Pad
J (x1)
Power Cord
I (x1)
Leg
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
Controller

3
TOOLS NEEDED
176lbs
(79.83kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Phillips
Screwdriver
STEP 2
Attach the two side brackets (E) to both ends of the frame using four M6x12mm bolts (S-A). Tighten all
screws with allen key (S-D).
Level
Loosen the two screws using the allen key (S-D). Adjust the frame length to suit the desktop. Retighten
all screws. Attach the telescopic crossbar (A) to the legs (H, I) as shown, using M6x12mm bolts (S-A).
NOTE: Insert all necessary screws into holes before completely tightening. Make sure adjusted length
of the telescopic crossbar is no more than 61" (155cm).

4
STEP 3
Loosen and remove the screws from hooks (G) with a screwdriver. Fix the hooks to the shelf (D) with
the previously removed screws. Tighten the screws.
STEP 5
With the frame upside down, place the feet (F)
on the legs as shown. Insert the bolts (S-A) in
the desk legs using an Allen Key (S-D).
STEP 4
Position the frame upright. Loosen the knobs on the sync rod (B) and extend the hex sha. Insert hex
sha into the leg (I), making sure the red bumper makes contact with the leg. While holding the hex
sha with one hand, extend sync rod onto the sha of the motorized leg, making sure the rod makes
contact with the red bumper on the motor sha. Tighten both knobs.

5
STEP 5 (continued)
Hang the shelf onto the center part of the telescopic crossbar. Tighten the screws.
STEP 6
Connect the AC adapter (C) and motorized leg to the controller
(K). Connect the power cord (J) to the AC adapter.
C
K

6
STEP 7
Remove the protective film from the adhesive rubber pads (S-F). Position the rubber pads on the side
brackets as shown.
STEP 8
If you are using a VIVO desktop, Refer to the manual that came with your desktop.
If you are not using a VIVO desktop, place the desktop on the frame, and secure the desktop using the
⅞” screws (S-B).

7
STEP 9
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.
Attach the controller to the underside of the desktop using 3/4"screws (S-C) as shown. Tighten
all screws. Once controller is installed, cable clips (S-E) can be attached to the desk for cable
management. Refer to Controller User Guide for operational instructions.

LAST UPDATED: 12/02/2020
REV4
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303