Vivo DESK-SF01W User manual

White Wall Mounted Desk with Drawer
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-sf01w
SKU: DESK-SF01W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
STEP 2
Insert x2 Cam Lock Screws (M) into front of Rear Panel (B) as shown. Insert x4 Wood Dowel
Pins (N) into top and sides of Rear Panel, and x4 Pins into rear and sides of Bottom Panel (D).
Assemble Rear Panel to Bottom Panel.
PACKAGE CONTENTS
TOOLS NEEDED
33lbs
15kg
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Desktop
B(x1)
Rear Panel
C(x1)
Le Panel
D (x1)
Bottom Panel
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1
Pull open Slider (K), then attach Slider to Le Panel (C) using x2 Screws (P), making sure the
arrow is pointing towards the front. Repeat for Right Panel (E).
E (x1)
Right Panel
F(x1)
Back Drawer
Panel
G(x1)
Right Drawer
Panel
H (x1)
Front Drawer
Panel
I (x1)
Drawer Floor
Panel
J (x1)
Le Drawer Panel
K(x2)
Slider
L (x10)
Mounting Hole
Cover
M (x32)
Cam Lock Screw
N(x24)
Wood Dowel Pin
O(x32)
Cam Lock Nut
P (x12)
ST4x16
W-A (x10)
ST4x35
W-B (x10)
Anchor
W-C (x10)
D6 Washer
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [email protected], or call us at 309-278-5303.
Q (x4)
ST5.5x50

4
STEP 7
Insert x2 Cam Lock Screws (M) into front of Back Drawer Panel (F). Insert x2 Wood Dowel Pins
(N) into sides of Back Drawer Panel (F), and x6 Wood Dowel Pins (N) into edges of Floor Panel
(I). Assemble Rear Drawer Panel to the Floor Panel.
STEP 8
STEP 9
Assemble the Right and le Drawer Panels (G,J) to the Rear and Floor Panel assembly as
shown below. Assemble the Front Drawer Panel (H) to the drawer assembly.
Insert x4 Cam Lock Screws (M) and x1 Wood Dowel Pin (N) into Right Drawer Panel (G). Repeat
for Le Drawer Panel (J). Insert x6 Cam Lock Screws into Front Drawer Panel (H).
STEP 3
Insert x4 Cam Lock Screws
(M) into Le Panel (C), and
x2 Wood Dowel Pins (N) into
top of Le Panel. Repeat for
Right Panel (E). Assemble Le
and Right Panels to previously
assembled Rear and Bottom
Panels (B, D).
STEP 5
Insert x6 Cam Lock Screws (M) into bottom of Desktop (A).
Place Desktop onto frame assembly.
STEP 4
Insert x6 Cam Lock Nuts (O) into top of Bottom Panel (D) and x4 Nuts into back of Rear Panel
(B). Turn all Nuts clockwise using a Phillips screwdriver to lock Panels together.
STEP 6
Insert x2 Cam Lock Nuts (O) into Le Panel (C), x2 Nuts into Right Panel (E), and x2 Nuts into
Rear Panel (B). Turn all Nuts clockwise using a Phillips screwdriver to secure Desktop (A).
J
G
H
5

Determine desired location of desk on wall. Use a stud finder to determine if any vertical
set of holes can be mounted into a wood stud or not. With the help of a partner, hold desk
against wall and mark (10X) mounting locations through Rear Panel (B). Use of a level is
recommended. Then proceed to Options A or B below.
Note: This desk is designed to mount securely in drywall only. However, it is still
recommended to install at least one set of vertical mounting points in a wood stud. Two
sets of mounting points are spaced 16” apart for the most secure mounting option (Option A
below).
Option A: Wood Stud Installation Only
For all locations that line up with a stud, drill 1.75” (45mm) deep holes using a 1/8” (3mm)
bit. If attaching desk with the 4X locations for wood studs, mount desk to wall using (4X)
ST5.5x50mm screws (Q) with (4X) washers (W-C). Install mounting hole covers (L) over all
holes on rear panel (B).
STEP 12
Pull Sliders (K) all the way forward. Secure assembled drawer to Sliders using x4 Screws (P).
Push drawer back into desk.
STEP 10
Insert Cam Lock Nuts (O) into all of the drawer panels shown below. Turn all Nuts clockwise
using a Phillips screwdriver to lock Panels together.
STEP 11
Option B: Drywall Installation
For all locations that do not line up with a stud, insert self-tapping drywall anchors (W-B)
using phillips screwdriver. If attaching desk with the 10X locations in drywall, mount desk to
wall using (10X) ST4x35mm screws (W-A) with (10X) washers (W-C). Install mounting hole
covers (L) over all holes on rear panel (B).
Note: If attaching desk with 2X locations in wood stud, refer to Option A for wood stud drilling
instructions. The remaining 6X mounting points should still be installed in drywall.
STEP 11 (Continued)
76

LAST UPDATED: 09/25/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303